LANDO BLUETOOTH SPEAKER ONOFF PACKAGE CONTENTS 1, LANDO Bluetooth Speaker 2. User's Manual 3. USB cable 4. Audio cable MIMI USB PORT i 6mm WOK act ie CHARGING THE SPEAKER:
Before using the speaker for the first time, charge it for at least 12 hours. 1. Plug the USB cable into the port on the speaker, plug the other end into the USB port on the computer. 2. Red LED will turn on to indicate that the unit is charging. 3. Red LED will tum off when fully charged. PAIRING THE DEVICE 1. Place the speaker near the Bluetooth-enabled device. 2. Slide the ON/OFF button to ON. The blue LED will flash 3 times slowly then flash quickly. The speaker is now in pairing mode. 3. Follow the instructions of your device to search for the speaker. 4, The speaker is called "LANDO "; enter the PIN "0000" if needed. 5. The blue LED will flash slowly when pairing is complete. BASIC INSTRUCTIONS To turn the speaker on, slide the ON/OFF button to ON. The Speaker will emit a beep and a blue LED will flash slowly. The blue LED will stay on when playing music. The speaker will emit a beep every 20 seconds when the battery is low. To turn the speaker off, slide the ON/OFF button to OFF. TECHNICAL SPECIFICATIONS:
Bluetooth standard: 2.1+EDR Bluetooth agreement: A2 DP Working distance: 30ft. Frequency range: 220Hz - 20KHz SIN Ratio: >80d8 Distortion Factor: <1.0%
Playing time: 2 hours Charge time: 2 hours , 3 hours first time. LED INDICATOR Charging: Red LED on Fully Charged: Red LED off Pairing Mode: Blue LED will flash quickly Connected: Blue LED will flash slowly Playing: Blue LED will remain on SAFETY AND GENERAL INFORMATION:
Do not expose the device to water or attempt to disassemble the device. If the device is exposed to water or disassembled, the user may be risking an electric short. Handle this product with care, without proper care the device may not function properly. Do not use this product in an aircraft or in a hospital. Do not expose the device to direct sunlight. Device may become warm while charging. NOTE: This equipment hes been tested and found to comply withthe requtements for @ Cass B gta dees under Bart 19 tthe Federal Communicators Commission FCC les, These eturemenis are intended 0 proude reasons provectonsonrat harm nicterenceina Rete and used in acrordsnce wrth 2 nerucbons, may ease harm wisrarsnce rae"
However there is na guarantee that interference wil nt occur ina pariculrinstalton, If this Squpmett dose eaves harmful intrlranoe oasis or few recneeon which canbe determines by ina Pe earn olson heuer rcersgd oy tcc he rears by ove mare the flown measures smn xrlocate me ecevng artenne soace ths soparsvon betwoon the equroment and receiver Conect ths eapment moan auton a cat erent Horm tat to which the adie: 710083 Ecncult the doair or an experienced radia/TV technician for help. Sonor onan Fe Maden China LANDO ENCEINTE BLUETOOTH CONTENU DE L'EMBALLAGE 1. LANDO Enceinte Bluetooth 2. Mode d'emploi 3. Cable USB. 4. Cable audio PORT MINIUSB JACK 35mm LED (ROUGEBLEUE) CHARGEMENT DE L'ENCEINTE Avant dutiliser enceinte pour la premire fois, chargez-la pendant au moins 12 heures. 1. Branchez le cable USB dans le port de enceinte, branchez l'autre extrmit dans le port USB de ordinateur. 2. LaLLED rouge sallume pour indiquer que l'appareil est en charge. 3. LaLED rouge steint lorsque l'appareil est compltement charg. APPAIRAGE DE L'APPAREIL Posez l'enceinte prs de l'appareil Bluetooth. Faites basculer linterrupteur marche/arrt sur ON . La LED rouge clignote 3 fois lentement et clignote ensuite rapidement. L'enceinte est a prsent en mode d'appairage. Suivez les instructions de votre appareil afin disoler votre enceinte Leenceinte est appele LANDO , entrez le code d'accs 0000 si ncessaire. La LED bleue ciignote lentement lorsque 'appairage a rus:
gee Ve INSTRUCTIONS DE BASE Pur allumer lenceinte, faites basculer linterrupteur marche/arrt sur ON . L'enceinte met un signal sonore et la LED bleue ciignote lentement. La LED bleue reste allume lorsque vous coutez de la musique. Lenceinte met un signal sonore toutes les 20 secondes lorsque le niveau de la batterie est faible. Pour teindre renceinte, faites basculer linterrupteur marche/arrt sur OFF . Tmoin LED Chargement : LED rouge allume Entigrement charge : LED rouge teinte Mode d'appairage : la LED rouge clignote rapidement Connexion : la LED rouge clignote lentement Mode lecture : LED bleve reste allume SPECIFICATIONS TECHNIQUES Norme Bluetooth : 2.1 +EDR Convention Bluetooth : A2 DP Distance de fonctionnement : 9 m Bande de frquence 220 Hz - 20 KHz Rapport S/B : > 80 dB Facteur de distorsion : <1,0%
Dure de lecture : 2 heures Temps de charge : 2 heures, 3 heures avant la toute premire utilisation. INFORMATIONS GENERALES ET RECOMMANDATIONS DE SECURITE Evitez d'exposer appareil a reau et ne tentez pas de le dmonter. Si 'appareil est expos a eau ou sil est dmont, rutiisateur peut provoquer un court-circuit lectrique. Manipulez cet appareil avec prcaution afin d'viter un mauvais fonctionnement. Cet appareil ne doit pas tre utilis dans un avion ou un hpital. Nrexposez pas directement 'appareil aux rayons du soleil Lappareil peut devenir chaud en cours de chargement. NtNo: 7190-55, ade in China