CO-8ZBS Carbon Monoxide Detector Introduction CO-8ZBS is a ZigBee Carbon Monoxide Detector. It is capable of sending wireless signals to the coordinator in the ZigBee network upon detection of Carbon Monoxide concentration. The Carbon Monoxide Detector utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable and has low power consumption and high transmission efficiency. Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal transmission. The Carbon Monoxide Detector Serves as an end device in the ZigBee network. It can be included in the ZigBee network to transmit signal upon activation, but cannot permit any other ZigBee device to join the network through the Carbon Monoxide Detector. Parts Identification 1. Dual Color LED indicator (Amber/Red) The LED indicator lights up in the following conditions:
- Red LED flashes twice The Carbon Monoxide Detector has successfully joined a ZigBee network.
- Red LED Flashes once every 20 minutes:
The Carbon Monoxide Detector has lost connection to its current ZigBee network.
- Amber LED flashes every second:
The Carbon Monoxide Detector is in Alarm Silence mode. 2. Function Button
- Press the button once to send a supervision signal.
- Press the button once during alarm to silence the alarm.
- Press and hold the button for 10 seconds then release to reset the Carbon Monoxide Detector. 3. Battery Compartment The Carbon Monoxide Detector is powered by three AA Alkaline 1.5V batteries. 4. Mounting Hole 5. Mounting Bracket Features CCaarrbboonn MMoonnooxxiiddee DDeetteeccttiioonn The Carbon Monoxide Detector will be activated according to the following table when CO concentration is detected. CO concentration level 30 ppm 50 ppm 100 ppm 300 ppm Time taken before alarming None 60-90 minutes 10-40 minutes Under 3 minutes Once the CO concentration level exceeds the threshold and persists for the time length as listed in the above table, the Carbon Monoxide Detector will transmit the signal to ZigBee network coordinator and raise alarm with its built-in siren. After the alarm has been activated, the Carbon Monoxide Detector will continue to send the alarm signal every 2 minutes as long as CO concentration remains above 30 ppm. If the CO concentration drops below 30 ppm, the Carbon Monoxide Detector will stop alarming and transmit a restore signal 1 AAllaarrmm SSiilleennccee When the Carbon Monoxide Detector is alarming, you can press the Function button once on Carbon Monoxide Detector to enter Alarm Silence mode for 10 minutes Under Alarm Silence mode, the Carbon Monoxide Detector will not sound alarm; the Amber LED Indicator will flash every second to indicate it is under Alarm Silence mode. After 10 minutes, if CO concentration still exceeds 30ppm, the Carbon Monoxide Detector will raise alarm and send alarm signal again. BBaatttteerryy aanndd LLooww BBaatttteerryy DDeetteeccttiioonn The Carbon Monoxide Detector uses three 1.5V Alkaline batteries as its power source. The batteries are included in the package. The Carbon Monoxide Detector feature Low Battery Detection function. When low battery voltage is detected, the Carbon Monoxide Detector will transmit Low Battery signal to notify the user. When changing batteries, after removing the old batteries, press the Function Button twice to fully discharge before inserting new batteries. SSuuppeerrvviissiioonn The Carbon Monoxide Detector will transmit a supervision signal to report its condition regularly according to user setting. The factory default interval is 30 minutes. The user can also press the Function Button once to transmit a supervision signal manually. ZigBee Network Setup ZZiiggBBeeee DDeevviiccee GGuuiiddeelliinnee ZigBee is a wireless communication protocol that is reliable and has low power consumption and high transmission efficiency. Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal transmission. Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join network after powering on. Since performing a task in connecting network may consume some power, it is required to follow the instructions to avoid draining battery of a ZigBee device
- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the ZigBee device.
- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee device is in use.
- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing the battery from a ZigBee device. JJooiinniinngg tthhee ZZiiggBBeeee NNeettwwoorrkk As a ZigBee device, the Carbon Monoxide Detector needs to join a ZigBee network to transmit signal when smoke concentration is detected. Please follow the steps bellow to join the Carbon Monoxide Detector into the ZigBee network. 1. Insert the batteries into the battery compartment to power on the Carbon Monoxide Detector. 2. The Carbon Monoxide Detector will emit two short beeps when it is powered on. 3. Press and hold the function button for 10 seconds then release to join ZigBee network. Please make sure to enable the permit-join feature on the router or coordinator of your ZigBee network 4. After joining the ZigBee network, the Carbon Monoxide Detector will be registered in the network automatically. Please check the ZigBee network coordinator, system control panel or CIE
(Control and Indicating Equipment) to confirm if joining and registration is successful. If the Carbon Monoxide Detector successfully joins the ZigBee network, the Red LED will flash twice to confirm. 5. After joining the ZigBee network, if the Carbon Monoxide Detector loses connection with its current ZigBee network, the Red LED will flash every 20 minutes to indicate. Please check your ZigBee network condition and Carbon Monoxide Detector signal range to correct the situation. RReemmoovviinngg DDeevviiccee ffrroomm ZZiiggBBeeee NNeettwwoorrkk ((FFaaccttoorryy RReesseett)) To remove the Carbon Monoxide Detector from current ZigBee network, the device must be put to Factory Reset to complete device removal. Factory Reset function will clear the Carbon Monoxide Detector of its stored setting information and prompt the device to search for new ZigBee network. Before removing device, make sure the Carbon Monoxide Detector is within current ZigBee network signal range 1. Press and hold the function button for 10 seconds, then release the button to reset Carbon Monoxide Detector. 2 2. Upon reset, the device will clear current ZigBee network setting and transmit signal to ZigBee coordinator to remove itself from current ZigBee network. It will then actively search for available ZigBee network again and join the network automatically. Installation IInnssttaallllaattiioonn GGuuiiddeelliinnee It is recommended to install the Carbon Monoxide Detector in following locations. Install the Carbon Monoxide Detector in your bedrooms to protect your safety. For houses with garage, also mount near the internal door to garage and the room above the garage for protection in case when car engin is not turned off. Avoid mounting in following locations. Inside kitchen and garage to avoid false alarm when Corner or location with stagnant air to avoid false alarm Fireplace Keep at least 4.5 meters of distance to avoid false alarm. IInnssttaallllaattiioonn A mounting bracket is provide in the package for mounting the Carbon Monoxide Detector on the wall. 1. Refer to Control Panel manual and put the Control Panel into Walk Test mode. 2. Put the Carbon Monoxide Detector at desired installation location, press the Learn/Test button to transmit signal to panel. 3. If the panel receives signal, it will display the device signal strength. Check and make sure the panel can receive signal normally from device at current location. If signal reception is unsatisfactory, relocate the Carbon Monoxide Detector and repeat Step 1~3 until an ideal installation location is found. 4. Use the mounting bracket as template to mark the two holes on the wall at chosen location for 5. Screw the mounting bracket onto the wall according to marked location. Install wall plugs if installing screws. necessary. 6. Hook the Carbon Monoxide Detector onto the mounting bracket. Installation is now complete. UUssiinngg CCaarrbboonn MMoonnooxxiiddee DDeetteeccttoorr wwiitthh ZZiiggBBeeee RRoouutteerr IMPORTANT NOTE If the Carbon Monoxide Detector installation location is away from your system control panel and requires ZigBee routers to improve signal strength. DO NOT use a ZigBee Router without backup battery. A ZigBee router without battery will be powered down during AC power failure and the Carbon Monoxide Detector connected to the router will lose connection with ZigBee network. You should plan your Carbon Monoxide Detector installation location using only ZigBee router with backup battery. Appendix (For developers only.) CCaarrbboonn MMoonnooxxiiddee DDeetteeccttoorr CClluusstteerr IIDD Device ID: IAS Zone 0x402 Endpoint: 0x01 Server Side Basic (0x0000) Identify(0x0003) IAS Zone(0x0500) None Mandatory Optional AAttttrriibbuuttee ooff BBaassiicc CClluusstteerr IInnffoorrmmaattiioonn Range Name Type Identifier Access Default 0x0000 0x0003 ZCLVersion HWVersion Unsigned 8-bit integer Unsigned 8-bit integer 3 0x00 0xff Read only 0x01 0x00 0xff Read only 0 Client Side None None Mandatory
/ Optional M O 0x0004 0x0005 0x0006 0x0007 0x0010 ManufacturerName ModelIdentifier DateCode PowerSource LocationDescription 0x0011 PhysicalEnvironment Character String Character String Character Character String 8-bit String 8-bit 0x0012 DeviceEnabled Boolean 0 32 bytes Read only 0 32 bytes Read only 0 16 bytes Read only Read only 0x00 0xff Read /
0 32 bytes Write Read /
Write Read /
Write 0x00 0x01 0x00 0xff Climax Technology
(Model Version) 0x00 0x01 O O O M O O M AAttttrriibbuuttee ooff IIddeennttiiffyy CClluusstteerr IInnffoorrmmaattiioonn Identifier Name Type Range 0x0000 IdentifyTime Unsigned 16-bit integer 0x00 0xffff Access Read /
Write Default 0x0000 Mandatory
/ Optional M Default Mandatory
/ Optional 0x00 0x00 0xFF M M M M M AAttttrriibbuuttee ooff IIAASS ZZoonnee CClluusstteerr IInnffoorrmmaattiioonn Range All All All Valid 64bit IEEE address All Access Read only Read only Read only Read /
Write Read only Identifier Name 0x0001 0x0002 0x0003 ZoneState ZoneType ZoneStatus 0x0010 IAS_CIE_ADDRESS 0x0011 ZONE_ID Type 8-bit 8-bit Enumeration Enumeration 16-bit bitmap IEEE ADDRESS Unsigned 8-bit integer 4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 5