Shutter Control (SCM-1ZBS) Introduction SCM-1ZBS is a ZigBee Shutter Control. The user can control the SCM via ZigBee network at a remote distance or manually by linking a switch to the Shutter Control. The Shutter Control utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal transmission. The Shutter Control serves as an end device in the ZigBee network. It can be included in the ZigBee network to transmit or receive signal, but cannot permit any other ZigBee device to join the network through the Shutter Control. Parts Identification 1. LED indicator The LED indicator is used to indicate Shutter Control status:
- Flashes once: The Shutter Control has reset.
- Flashes twice: The Shutter Control has successfully joined a ZigBee network.
- Flashes once every 20 minutes:
The Shutter Control has lost connection to its current ZigBee network. 2. Function Button
- Press once: Transmit a supervision signal.
- Press and hold for 3~10 seconds: Enter calibration mode.
- Press and hold for 10 seconds: Reset the Shutter Control to join ZigBee network. 3. Insertion Hole Clipper Opener Press the button to open the clipper of the respective insertion hole 4. Wire Insertion Holes (With clippers) 5. Power Input Terminal L (Live Lead) 6. Power input Terminal N (Neutral Lead) 7. Local Switch Terminal S1 (Open Direction) Connect an external switch to this terminal. Activate this switch to control the shutter to roll toward Open direction by activating the Motor Output O1 Activating this switch when the shutter is rolling towards the Close direction will stop the shutter. 8. Local Switch Terminal S2 (Close Direction) Connect an external switch to this terminal. Activate this switch to control the shutter to roll toward Close direction by activating the Motor Output O2 Activating this switch when the shutter is rolling towards the open direction will stop the shutter. 9. Motor Output O1 (Open Direction) Connect to the Open terminal of the Shutter Motor. 10. Motor Output O2 (Close Direction) Connect to the Close terminal of the Shutter Motor. ZigBee Network Setup ZZiiggBBeeee DDeevviiccee GGuuiiddeelliinnee ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and are coordinated for data exchange and signal transmission. 1 JJooiinniinngg tthhee ZZiiggBBeeee NNeettwwoorrkk As a ZigBee device, the Shutter Control needs to join a ZigBee network to receive commands. Please follow the steps bellow to join the Shutter Control into a ZigBee network. 1. Connect the power cable to AC Input connector on Shutter Control. 2. Press and hold the function button for 10 seconds as the Shutter Control resets and starts searching for existing ZigBee network. Please make sure the permit-to-join feature on the router or coordinator of your ZigBee network is enabled. If the Shutter Control successfully joins a ZigBee network, the LED Indicator will flash twice to confirm. 3. 4. After joining the ZigBee network, the Shutter Control will be registered in the network automatically. Please check the ZigBee network coordinator, system control panel or CIE (Control and Indicating Equipment) to confirm if joining and registration is successful. 5. After joining the ZigBee network, if the Shutter Control loses connection to the current ZigBee network, the LED indicator will flash every 20 minutes. Please check your ZigBee network condition and Shutter Control signal range to correct the condition. Removing Device from ZigBee Network (Factory Reset) To remove the Shutter Control from current ZigBee network, the Shutter Control must be put to Factory Reset to complete device removal. Factory Reset function will clear the Shutter Control of its stored setting information and prompt the device to search for new ZigBee network. Before removing device, make sure the Shutter Control is within current ZigBee network signal range 1. Press and hold the function button for 10 seconds, then release the button to reset Shutter Control. 2. Upon reset, the Shutter Control will clear current ZigBee network setting and transmit signal to ZigBee coordinator to remove itself from current ZigBee network. It will then actively search for available ZigBee network again and join the network automatically. Installation Please use the recommended wire size of AWG 16-26 or 1.31-0.129 (mm). Connect SCM according to the diagram below:
Connect L terminal of SCM to the L terminal of Power Supply. Connect N terminal of SCM to the N terminal of Power Supply. Connect O1 terminal of SCM to the Open terminal of the Shutter Motor. Connect O2 terminal of SCM to the Close terminal of the Shutter Motor.
(Optional local switch) Connect S1 and S2 terminals of SCM to the L terminal of Power Supply. Operation CCaalliibbrraattiioonn The Shutter Control default activation time is 4 minutes. When the Up/Down button is pressed or the ZigBee network coordinator transmits Up/Down command, it will activate the Shutter Motor for 4 minutes. For the Shutter Control to work properly, its activation time must be calibrated. There are two ways to adjust the activation time:
ZigBee Command: The activation time can be adjusted by sending command from the ZigBee network coordinator. (See Appendix Level Cluster Attribute OnTransitionTime
/
OffTransitionTime, minimum adjustable unit 100ms) 2 Manual Calibration: Calibrate the activation according to procedure below:
1. Before calibration, the external local switches must be connected to the Shutter Control. 2. Press and hold the Function button for 3~10 seconds and release to enter Calibration mode. The Shutter Control will roll toward the Open direction for 4 minutes upon entering Calibration mode. 3. Wait for 4 minutes for Shutter Control to stop rolling to Open direction, then activate the connected external local Close switch to close the shutter. 4. Activate the Open external local switch the moment the shutter is fully closed. The Shutter control will record to time it took between step 3 and 4 as the new close time. 5. The Shutter Control will roll toward open direction after step 4. 6. Activate the Close external local switch the moment the shutter is fully opened. The Shutter control will record to time it took between step 5 and 6 as the new open time. Example If it takes 30 seconds for the shutter to move from Open to Close, and 40 seconds to move from Close to Open, the new close time will be 30 seconds and new open time will be 40 seconds. After calibration, whenever the Shutter Control receives close command, it will roll toward close direction for 30 seconds. When it receives open command, it will roll toward open for 40 seconds. The activation time will be reset to 4 minutes whenever the Shutter Control joins a ZigBee network. SShhuutttteerr CCoonnttrrooll ZigBee Network After the Shutter Control has successfully joined a ZigBee network, the coordinator can remotely control the shutter to open, close or stop by transmitting command though ZigBee network. When the Shutter Control receives open/close signal from coordinator, it will roll toward open/close direction according to calibrated activation time to fully open/close the shutter. The Shutter status can also be adjusted by percentage from 0%, 10%, 20%... to 100% through ZigBee Coordinator. The current open percentage is also transmitted to ZigBee coordinator. Local Switch If an optional Local Switch is connected, users can also press the switch button to open/close the shutter. Press and release the switch for less than 1 second will control the shutter to fully open or close. Press and hold the switch for more than 1 second will control the shutter to open and close until the switch is released. When the switch is released, the shutter will stop. Pressing the switch when the shutter is moving to opposite direction will stop the shutter. Press the switch again to open/close the shutter. For example, pressing the down switch when the shutter is opening will stop the shutter, press down switch again to start closing the shutter. MMaaxxiimmuumm OOppeerraattiioonn LLooaadd For 110V: the maximum operation load is 440W and 4A. For 230V: the maximum operation load is 920W and 4A. Appendix (For developers only) PPoowweerr RReellaayy SShhuutttteerr CCoonnttrrooll wwiitthh MMeetteerr CClluusstteerr IIDD Device ID: Shade :0x0200 Endpoint:0x01 Server Side Basic (0x0000) Identify(0x0003) On/Off(0x0006) Level Control(0x0008) Shade Config(0x0x0100) Groups(0x0004) Scenes(0x0005) Mandatory Optional 3 Client Side None None AAttttrriibbuuttee ooff BBaassiicc CClluusstteerr IInnffoorrmmaattiioonn Identifier Name Type Range Access Default None Mandatory
/ Optional M O O O O O M O O M Mandatory
/ Optional Mandatory
/ Optional M Mandatory
/ Optional M O O Mandatory
/ Optional M M 0x0000 0x0001 0x0003 0x0004 0x0005 0x0006 0x0007 0x0010 0x0011 0x0012 ZCLVersion ApplicationVersion HWVersion ManufacturerName ModelIdentifier DateCode PowerSource LocationDescription PhysicalEnvironment DeviceEnabled Unsigned 8-bit integer Unsigned 8-bit integer Unsigned 8-bit integer Character String Character String Character String 8-bit Character String 8-bit Boolean Unsigned 16-bit integer 0x00 0xff Read only 0x00 0xff Read only 0x00 0xff Read only 0x01 0x00 0 0 32 bytes 0 32 bytes 0 16 bytes 0x00 0xff 0 32 bytes 0x00 0xff 0x00 0x01 Read only Read only Read only Read only Read / Write Read / Write Read / Write Climax Technology
(Model Version) 0x00 0x01 AAttttrriibbuuttee ooff IIddeennttiiffyy CClluusstteerr IInnffoorrmmaattiioonn Identifier Name Type Range Access Default 0x0000 IdentifyTime 0x00 0xffff Read / Write 0x0000 M AAttttrriibbuuttee ooff OOnn//OOffff CClluusstteerr IInnffoorrmmaattiioonn Identifier 0x0000 Identifier Name OnOff Type Boolean 0x00 0x01 AAttttrriibbuuttee ooff LLeevveell CClluusstteerr IInnffoorrmmaattiioonn Range Name Type Range 0x0000 0x0012 0x0013 CurrentLevel OnTransitionTime OffTransitionTime Unsigned 8-bit integer Unsigned 16-bit Unsigned 16-bit integer integer 0x00 0xff 0x0000 0xFFFF 0x0000 0xFFFF Access Read only Default 0x00 Access Default Read only Read / Write Read / Write 0x00 0x0960 0x0960 AAttttrriibbuutteess ooff tthhee SShhaaddee cclluusstteerr IInnffoorrmmaattiioonn Identifier 0x0002 0x0010 0x0011 Name Status ClosedLimit Mode Type Range 8-bit bitmap Unsigned 16-bit integer 8-bit Enumeration 0000xxxx B 0x0001 0xfffe 0x00 0xfe Access Read / Write Read / Write Default 00000000 B 0x0001 Read / Write 0x00 M Name AAttttrriibbuutteess ooff tthhee GGrroouuppss cclluusstteerr IInnffoorrmmaattiioonn Access Read only AAttttrriibbuutteess ooff tthhee SScceenneess cclluusstteerr IInnffoorrmmaattiioonn Access Range x0000000 NameSupport 8-bit bitmap Range Name Type Type Identifier 0x0000 Identifier 0x0000 0x0001 0x0002 0x0003 0x0004 SceneCount CurrentScene CurrentGroup SceneValid NameSupport Unsigned 8-bit integer Unsigned 8-bit integer Unsigned 16-bit integer Boolean 8-bit bitmap 0x00 0xff Read only 0x00 0xff 0x0000 0xfff7 0x00 0x01 x0000000 Read only Read only Read only Read only 4 Default
-
Default 0x00 0x00 0x00 0x00
-
Mandatory
/ Optional M Mandatory
/ Optional M M M M M Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 5