FCC ID: OSZ3163B1 WLAN PCMCIA NETWORK Adapter

PRELIMINARY Data Sheet November 1999 File Number 4794 HWB3163-EVAL

[ /Title

(HWB 3163-

EVAL

)

/Sub-

ject

(PRIS M II 11Mbp s Wire-

less Local Area Net-

work PC Card)

/Autho r ()

/Key-

words

(Inter-

sil Corpo-

ration, semi-

con-

ductor, Wire-

less Com-

muni-

cations

, RF, Radio Fre-

quency PRISM II 11Mbps Wireless Local Area Network PC Card The Intersil HWB3163 WLAN PC Card

(Note 1) is a complete wireless high speed Network Interface Card (NIC) utilizing the Intersil PRISM II Direct Sequence Spread Spectrum Wireless Transceiver chip set. It provides a complete evaluation platform of hardware and software to system providers or integrators requiring wireless data communications capability and is ideal for integration into computer platforms. Evaluation kits include two WLAN PC cards, a Microsoft Windows 95/98/NT Driver, LANEVAL software, PRISM Transmitter Test Utilities (PTTU) software (Note 3) and documentation to get your evaluation started quickly. Supporting the IEEE 802.11 network specication for Direct Sequence Spread Spectrum DSSS signaling, the card is packaged in a PCMCIA Type II extended cover set. The card provides data rates of 1, 2, 5.5 and 11Mbps. Access Points will be available from a number of suppliers, enabling a total wireless network solution. TYPICAL OPERATING RANGE (NOTE 2) DATA RATE

(Mbps) 11 5.5 2 1 INDOOR RANGE OUTDOOR RANGE 120 feet (37 meters) 400 feet (122 meters) 200 feet (61 meters) 600 feet (183 meters) 240 feet (73 meters) 750 feet (228 meters) Features FCC Certied Under Part 15 to Operate in 2.4GHz ISM Band (Approval Pending) Support for 11, 5.5, 2 and 1 Megabit Per Second (Mbps) Data Rates Supports the lEEE 802.11 Direct Sequence Specication Driver Supports Microsoft Windows 95, 98, 2000, NT, CE and LINUX Integrated Microstrip Dual Diversity Antennas Advanced RAKE Receiver Design with AGC Uses 50% of the Power of Previous Devices Provides Wireless Data Communications at Full Ethernet Speed Completely Covered Assembly is Designed to Fully Support PCMCIA Type II Dened Mechanical and Environmental Stress Conditions Intelligent Power Control, Including Low Power Standby Mode Complete Reference Design, the HWB3163-CD Available to Ensure Minimum Time-to-Market NOTES:

1. Throughout this document, all references to PC Card, WLAN adapter, adapter, or card refer to a covered card assembly conforming to the mechanical size specifications of the PCMCIA Standard Release 2.0, Type Il Extended (5.0mm) definition. 2. The range will vary in different operating environments due to 300 feet (91 meters) 1000 feet (305 meters) effects such as building construction. Ordering Information PART NUMBER DESCRIPTION CARDS/SET HWB3163-EVAL WLAN Evaluation Kit 2 Packaging 3. At present, PTTU supports Windows 95 and 98. An upgrade is in process which will add support for NT. 169 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright Intersil Corporation 1999. PRISM and PRISM II logo are trademarks of Intersil Corporation. Microsoft and Windows and Windows NT are registered trademarks of Microsoft Corporation. LINUX is a registered trademark of Linux Torvalds. HWB3163-EVAL Functional Overview The WLAN PC Card is designed to operate in the 2.4GHz ISM frequency band, channels 1 to 11, as specified by the FCC in the USA. The Card will also operate on channels 12 through 14, where permitted by local regulatory authorities (refer to Table 2). Radio equipment must be certified in a country prior to use. Refer to Table 3 for a list of countries and agencies that have approved the HWB3163-EVAL for operation. The Intersil PRISM Chip Set allows for high level integration for reduced size, increased throughput, improved radio performance and faster time to market. The WLAN PC card implements Direct Sequence Spread Spectrum DSSS technology providing superior noise and signal jamming immunity including less severe impact from unintentional radiators such as microwave ovens. The user can connect the PC Card in an ad-hoc peer to peer networking scheme, allowing for instant network setup in any ofce environment. By using an access point, the wireless LAN can be set up to allow for a greater number of users to interconnect, and to increase the coverage area. With a portal (i.e., Access Point), the wireless LAN can be easily connected into an existing wired LAN, allowing for easy expansion of the service. Compared to the rst generation PRISM I chip set, the PRISM II generation offers:

The HFA3841 Media Access Controller

(MAC) Protocol Handler The HFA3841 MAC and its rmware are responsible for running the IEEE 802.11 protocol in the WLAN card. This section describes the features of IEEE 802.11 that are implemented. The functions supported by the STA (station) Firmware are:

CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) with Random Backoff WEP Security Short/Long Preamble with multirate RTS/CTS Handshake (Ready To Send/Clear To Send) and NAV Management (Network Allocation Vector) MAC Level Acknowledgments (Media Access Control) Re-Transmission of Unacknowledged Frames Duplicate Detection and Rejection Broadcast and Multicast Frames Fragmentation and Re-Assembly Power Management (Planned) Timestamp Synchronization 3.3V operation for reduced power dissipation DCF (Distributed Coordination Function) 50% reduction in current drain for extended battery life PCF (Point Coordination Function) Transmitter Automatic Level Control (ALC/AGC) to provide constant RF power output Sophisticated RAKE receiver and Automatic Gain Control (AGC) for improved multipath performance Higher level of chip integration and less peripheral components to yield 30% reduction in material cost Support of optional IEEE 802.11 Short Preamble for signicantly increased data throughput A complete Reference Design CD, the HWB3163-CD is available to ensure minimum time-to-market. This CD contains detailed information for manufacturing a PCMCIA WLAN assembly, including Gerber PC board les, an accurate Bill of Material with component sourcing and complete mechanical drawings. Related Literature To learn more about what the IEEE 802.11 is, refer to:

Tech Brief TB337, Intersil Corporation, A Brief Tutorial on Spread Spectrum and Packet Radio [1]. For a more detailed description of radio operation, please refer to:

Application Note AN9864, Intersil Corporation, HWB3163-EVAL PRISM II 11Mbps WLAN PCMCIA Card Users Guide [2]

170 Beacon Generation in an Ad-Hoc Network Probe Response Generation in an Ad-Hoc Network Card Information Structure The standard Intersil WLAN PC Card will be supplied with the following information embedded in the CIS. It should be noted that in most systems this information is displayed when the card is inserted. Customization of the CIS for specic customer requirements is available upon request, to enable customer information to be displayed when the card is inserted. TABLE 1. FUNCTION NAME CONTENT Manufacturers ID 00 Function ID Network Adapter Product Revision 1 Manufacturer Intersil Corporation Product PROG LOT HFA3841 HWB3163-EVAL The HWB3163 is shipped with USA-compliant rmware. In order to ensure regulatory-compliant channel usage in a particular country, special geographic-specic rmware is available for customer production assemblies which restricts channel usage. Examples include ETSI-compliant rmware, etc. Since the end user does not have the ability to alter this rmware, regulatory compliance is ensured. Agency and Regulatory Body Approvals The WLAN PC Card will comply to the following standards:

TABLE 3. COUNTRY APPROVAL NOTES USA FCC part 15, Sec. 15.247, Sec. 15.107 and 15.109 Approval pending for Intentional Radiators Computer Peripheral Canada ICAN RSS-210 Designed for compliance Europe ETSI 300.328 Nov 96 EMC prETS 300.826 Designed for compliance Japan MKK Designed for compliance 3V PCMCIA Interface Standard CAUTION: This assembly is designed to operate with a supply voltage of 3.3V in laptop computers supporting the dual 3V/5V PCMCIA standard. As such, it is mechanically keyed with a wide tab to prevent insertion in older laptops only capable of supplying 5V power. Do not therefore force engagement of the card in the PCMCIA slot of the laptop as the computer might not be supporting the newer standard. Permanent damage may occur if operated on 5V. IEEE 802.11 International Agreement and Frequency Assignments The IEEE 802 LAN committee has forged an international agreement providing for wireless data communication standards for the frequency range of 2.4GHz to 2.4835GHz, as allocated by the FCC in the USA, and in the 2.471GHz to 2.497GHz frequency range, as specified by the regulatory authority in Japan. These standards are designed to focus the industry to develop highly integrated, low cost, interoperable WLAN equipment, of which the HWB3163-EVAL is a prime example. In the U.S., there are 11 channels specied by the FCC in the 2.412GHz to 2.462GHz range. In Japan, one channel at 2.484GHz is authorized. The ETSl (European) regulatory body conforms to the USA (FCC) channel assignments with the exception that channels 12 and 13 are also allowed. Some countries in Europe, notably France and Spain have unique channel restrictions. Although information contained in Table 2 is deemed to be accurate, local regulatory authorities should be consulted before using such equipment. The available channels of operation in the 2.4GHz to 2.4835GHz and 2.471GHz to 2.497GHz ranges are as follows:

TABLE 2. IEEE 802.11 CHANNELS CHANNEL NUMBER CHANNEL FREQUENCY GEOGRAPHIC USAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2412MHz 2417MHz 2422MHz 2427MHz 2432MHz 2437MHz 2442MHz 2447MHz 2452MHz 2457MHz 2462MHz 2467MHz 2472MHz 2484MHz US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI US, CA, ETSI, FR, SP US, CA, ETSI, FR, SP ETSI, FR ETSI, FR Japan KEY: US = United States, CA = Canada, ETSI = ETSI countries

(except France and Spain), FR = France, SP = Spain. In Japan, authorization for Channels 1 through 11 is pending. 171 HWB3163-EVAL Absolute Maximum Ratings Supply Voltage . -0.3V to 4.0V (Max) Storage Temperature (Note 4) . -20oC to 65oC Operating Conditions Temperature Range . 0oC TA 55oC Supply Voltage Range . 3.0V to 3.6V Caution: These are the absolute maximum ratings for the PC Card product. Exceeding these limits could cause permanent damage to the card. NOTE:

4. All temperature references refer to ambient conditions. Electrical Specications Test Conditions: Supply Voltage (VCC) = 3.3V, Ambient Temperature (TA) = 25oC, Unless Otherwise Specied PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS CURRENT CONSUMPTION Average Current

(Without Power Saving Mode) (Note 5) Average Current

(With Power Saving Mode) (Note 5) Continuous Transmit Mode Continuous Receive Mode Standby (Note 5) PC CARD LOGIC LEVELS Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Input Leakage Current PC CARD LOADING CAPACITANCE Input Capacitance Output Capacitance ENVIRONMENTAL SPECIFICATIONS Vibration Drop Torque ESD X-RAY UV Humidity EMI RF SYSTEM SPECIFICATIONS Antenna Gain Transmitter Power Output EIRP 172 ICC ICC ICC ICC ICC VIH VIL VOH VOL IIH or IIL CIN COUT Vib Drop T 2% Transmit 98% Receive 2% TX 90% Standby 8% RX Sourcing 1mA Sinking 2mA 10 to 2000Hz, VCC = 0 10o Max ESD Non-Operating Wavelength 254nm X-RAY UV RH EMI AG POUT EIRP

-

-

-

-

-

0.7VCC 0.0 VCC-0.2 0

-10

-

-

-

-

-

-

-

-

-

-

-

-

-

218 40

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

+2.5

+12.5

+15

-

-

380 215 17 VCC +0.2 VCC/3 VCC 0.2 10 15 15 15 75 11 mA mA mA mA mA V V V V A pF pF G cm Lb/Ft2 1500 V 10K 15K 98 1K

-

-

-

Roentgen W/cm

%

Oersted dBi dBm dBm HWB3163-EVAL Electrical Specications Test Conditions: Supply Voltage (VCC) = 3.3V, Ambient Temperature (TA) = 25oC, Unless Otherwise Specied (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Receive Sensitivity RX_S 5.5Mbps, 8% PER or 1E-5 BER 11Mbps, 8% PER or 1E-5 BER Maximum Receive Level RX_MAX PER <8%

Third Order Intercept Point (Input) IIP3_90

-90 dBm input Image Rejection IF Rejection Adjacent Channel Rejection Data Rate (Physical Layer) IIP3_25

-25 dBm input PER <8%

PER <8%

PER <8% (Note 6) IR IFR ACR Rate

-

-

-4

-16

+10

-

60

-

-

-87

-84

-

-3

+20 60 100 46 1, 2, 5.5 and 11

-

-

-

-

-

-

-

-

-

dBm dBm dBm dBm dBm dB dB dB Mbps NOTES:

5. Refer to Application Note PRISM Power Management Modes AN9665 [5]. 6. The adjacent channel measurement is carried out on two channels separated by 25MHz (5 channels). PIN 34 TOP (LED, THIS SIDE) PIN 1 3V KEY PIN 68 BOTTOM PIN 35 VIEW, LOOKING INTO 68 PIN FEMALE CONNECTOR FIGURE 1. EDGE VIEW, PCMCIA CARD Back PC Card Label References For Intersil documents available on the internet, see web site http://www.intersil.com/

Intersil AnswerFAX (321) 724-7800.

[1] TB337 Tech Brief, Intersil Corporation, A Brief Tutorial on Spread Spectrum and Packet Radio, AnswerFAX document No. 82337.

[2] AN9864 Application Note, Intersil Corporation, HWB3163-EVAL PRISM II 11Mbps WLAN PCMCIA Card Users Guide Further information can be found in the following:

Intersil PRISM II datasheets, web home page, http://www.intersil.com/prism/prism.asp IEEE 802.11 Standards Project (available from the IEEE, New York, USA). PC Card V2.1 Standard. 173 HWB3163-EVAL Notices Electronic Emission Notices This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement The wireless LAN PC card is subject to the rules of the Federal Communications Commission (FCC). This card is considered an intentional radiator as per the FCC guidelines. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced ratio/TV technician for help WARNING! Any changes or modications of equipment not expressly approved by Intersil could void the users authority to operate the equipment. All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certication. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-

out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Ofce Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 174 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029