FCC ID: R33C4EA3 Controller for home automation system

Control4 EA-3 Controller Installation Guide Supported model C4-EA3 Entertainment and Automation Controller, 3 Zone Introduction The low-cost EA-3 Controller in the Entertainment and Automation line of controllers lets you control lights, home theaters, audio and video, and other devices controlled by infrared (IR), IP, or serial connections. The controller has a fast processor, dual-spectrum built-in WiFi, HDMI output for Control4 On-Screen Navigator, and ZigBee radio. The EA-3 is perfect for single rooms or smaller homes. The controller also includes extensive media management for audio and video content: CDs, DVDs, and Blu-ray Discs; digital media stored on connected devices and streaming audio services, such as Rhapsody, TuneIn, and others. Use an external storage device, such as an external USB drive or NAS (network-

attached storage), to store music and photos. The EA-3 Controller mounts easily on a wall behind the TV. After you install and configure the controller with other Control4 devices, your customers can control their system using popular Control4 interfaces (sold separately). Box contents The following items are included in the box:

Control4 EA-3 Controller (C4-EA3) EA-3 Wall-Mount Bracket (C4-WMEA3) AC power cord IR emitters (6) Dual-band antennas (2) Single-position terminal block for contact/relay Warranty card Accessories sold separately Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B) Rack Mount Kit (C4-XXXX) EA-3 Wall-Mount Bracket (C4-WMEA3) Warnings Caution! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. Avertissement ! Pour rduire le risque de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. Caution! In an over-current condition on USB or contact output the software disables the output. If the attached USB device or contact sensor does not appear to power on, remove the device from the controller. Avertissement ! Dans une condition de surintensit sur USB ou sortie de contact le logiciel dsactive sortie. (additional translation needed) For more information, visit the Products pages at www.control4.com. Requirements and specifications Note: We recommend using Ethernet instead of WiFi for the best network connectivity. Note: The Ethernet or WiFi network should be installed before you install the EA-3 Controller. Composer Pro is required to configure this device. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. Specifications Model number Video out Video Audio out Audio in Audio playback formats Ethernet Power over Ethernet Built-in Ethernet switch Wireless Wireless security Wireless antenna ZigBee Pro ZigBee antenna USB port IR OUT IR capture SERIAL OUT Contact Relay Power requirements Power consumption Operating temperature Storage temperature C4-EA3 Inputs / Outputs 1 video out1 HDMI HDMI 1.4 output; HD 720p/1080p, 50-60 Hz 3 audio out1 HDMI, 1 stereo analog (3.5 mm), 1 digital coax 2 audio in1 stereo analog (3.5 mm), 1 digital coax MP3: 32 kbps to 320 kbps, iTunes Plus, WMA, WMA lossless, Apple lossless, CBR, VBR, AAC, FLAC, and uncompressed WAV and AIFF. Network 10/100/1000BaseT compatible (required for controller setup). PoE+ supported. 802.3af / 12.95W 1 Ethernet/PoE in + 1 Ethernet switch port Dual-Band Wireless-N (2.4GHz, 5GHz, 802.11n/g/b) WEP, WPA, and WPA2 External reverse SMA connector 802.15.4 External reverse SMA connector 1 USB 2.0 port, 500mA minimum, 600mA maximum Control 6 IR out, 5V 27mA max output 1 IR blaster, front 1 IR receiver, front; 0-60 KHz 3 Serial out (shared with IR out 1-3) 1 contact sensor36V DC maximum operation. The available current for 12V contact output is 1.25A maximum. 1 relayAC: 36V, 2A; DC: 24V, 2A maximum operation. Power 100-240 VAC, 60/50Hz or PoE+

Max: 18W, 61 BTUs/hour Idle: 9W, 30 BTUs/hour Other 32 - 104 F (0 - 40 C) 4 - 158 F (-20 - 70 C) Fan dB level Dimensions (H x W x D) Max: 35 dB 8.75" (221 mm) x 5.875" (149 mm) x 1.25"

(31 mm) Weight 1.60 lbs (0.74 kg) Shipping weight Additional resources The following resources are available for more support. 2.75 lbs (1.26 kg) Control4 Knowledgebase: kb.control4.com and Dealer Forums:

forums.control4.com Control4 Technical Support Control4 website: www.control4.com Composer Pro documentation in online help or PDF format available on the Dealer Portal under Support: ctrl4.co/docs Front view A B C D E A Data LEDThe LED indicates that the controller is streaming audio. B IR windowIR blaster and IR receiver for learning IR codes. C Caution LEDThis LED shows solid red, then blinks blue during the boot process. Note: The Caution LED flashes yellow during the factory restore process. See Factory Restore in this document. D Link LEDThe blue LED indicates that the controller has been identified in a Control4 Composer project and is communicating with Director. E Power LEDThe blue LED indicates that AC power is connected. The controller turns on immediately after power is applied to it. Back view A B C D E F G H I KJ L NM A WIFIReverse SMA connector for WiFi antenna. B Power plug portAC power receptacle for an IEC 60320-C5 power cord. C Contact/Relay portConnect one relay device and one contact sensor device to the terminal block connector. Relay connections are COM, NC (normally closed), and NO (normally open). Contact sensor connections are +12, SIG (signal), and GND (ground). D Serial and IR OUT3.5 mm jacks for up to six IR emitters or for a combination of IR emitters and serial devices. Ports 1, 2, and 3 can be configured independently for serial control or for IR control. See Connect IR/serial ports in this document for more information. E DIGITAL COAX INAllows audio to be shared over the local network to other Control4 devices. F AUDIO IN and OUTStereo audio input and output ports (3.5 mm stereo audio jack). Allows audio to be shared (AUDIO IN) over the local network to other Control4 devices. Outputs audio (AUDIO OUT) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn). G DIGITAL COAX OUTOutputs audio (AUDIO OUT) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn). H HDMI OUTAn HDMI port to display navigation menus. Also an audio out over HDMI. ID buttonButton to identify the device in Composer Pro. I J FACTORY RESTORERestores the controller to its factory defaults. This also reboots the controller. K USBOne port for an external USB drive. See Set up external storage devices in this document. L EthernetEthernet port that can be used as a network switch to connect another local Ethernet device to the network. M Ethernet/POERJ-45 jack for a 10/100/1000 BaseT Ethernet connection. Use this port as the uplink port to your local network. If using PoE+ to power the controller, this port must be used. N ZIGBEEReverse SMA connector for ZigBee antenna. Installing the controller To install the controller:

1 Ensure that the home network is in place before starting system setup. The controller requires a network connection, Ethernet

(recommended) or WiFi, to use all of the features as designed. When connected, the controller can access web-based media databases, communicate with other IP devices in the home, and access Control4 system updates. 2 Mount the controller behind a TV, on a wall, placed in a rack, or stacked on a shelf. See Wall mount options below if mounting the controller on a wall or behind a TV. 3 Connect the controller to the network. EthernetTo connect using an Ethernet connection, plug the data cable from the home network connection into the controllers RJ-

45 port (labeled ETHERNET/POE) and the network port on the wall or at the network switch. Note: If using PoE+ to power the controller, make all connections prior to plugging in the PoE injector or switch. WiFiTo connect using WiFi, first connect the controller to Ethernet, and then use Composer Pro System Manager to reconfigure the controller for WiFi. Important: Do not install your EA controller on a 172.18.xxx.xxx subnet. 4 Connect system devices. Attach IR and serial devices as described in Connect the IR ports/serial ports and Set up IR emitters. 5 Set up any external storage devices as described in Setting up external storage devices in this document. 6 Power up the controller. Plug the power cord into the controllers power plug port and then into an electrical outlet. Mounting the controller behind a TV or on the wall Using the included Wall-Mount Bracket (C4-WMEA3), the EA-3 can easily be mounted behind a TV, on the wall using a 1- or 2-gang wall box, or mounted directly on the wall. See the EA-3 Wall-Mount Bracket Installation Guide for details. Pluggable terminal block connectors For the contact and relay ports, the EA-3 makes use of a pluggable terminal block connector which is a removable plastic part that locks in individual wires (included). To connect a device to the pluggable terminal block:

1 Insert one of the wires required for your device into the appropriate opening in the pluggable terminal block you reserved for that device (see Figure 3). 2 Insert the wire:

If using solid-core wire, insert the wire into the hole below the slotted retention tab, and ensure that the wire is tightly secured. If using stranded wire, press the slotted retention tab in using a small, flat-blade screwdriver. Insert the wire into the hole below the tab, and then release the tab to secure the wire. Example: If you add a motion sensor (see Figure 5), connect its wires to the following contact openings:

Power input to +12V Output signal to SIG Ground connector to GND Note: If you connect dry contact closure devices, such as doorbells, connect the switch between +12V (Power) and SIG (Signal). Power cycle the controller Press and hold the ID button for five seconds. The controller will reset. Reset the network settings To reset the controller network settings to the default:

1 Disconnect power to the controller. 2 While pressing and holding the ID button on the back of the controller, reconnect power to the controller. 3 Hold the ID button until the data, link and power LEDs are solid blue, then immediately release the button. 4 If the caution LED stays orange during the boot sequence, press and hold the ID button until the caution LED blinks blue, and then release it. Regulatory/Safety information To review regulatory information for your particular Control4 products, see the information located on the Control4 website at www.control4. com/regulatory/. Warranty Visit www.control4.com/warranty for details. More help For the latest version of this document and to view additional materials, open the URL below or scan the QR code on a device that can view PDFs. MOST RECENT VERSION MORE INFO ON EA CONTROLLERS ctrl4.co/ea3-ig ctrl4.co/ea Connecting the contact port The EA-3 provides one contact port for the included pluggable terminal block. See Figures 3 through 5 to learn how to connect the device to the contact port. Figure 3. Contact Port for Voltage Source ( Motion Sensor) Figure 4. Contact for Dry Contact ( Door Contact Sensor) Figure 5. Contact for Self-Powered Voltage Source Device Connecting the relay port The EA-3 provides one relay port for the included pluggable terminal block. With most applications, attach one wire to the COM terminal and the other to the NO terminal. The relay switch closes when the relay is activated. Figure 7. Relay Port, Normally Open Figure 8. Relay Port, Normally Closed Connecting the IR ports/serial ports (optional) The controller provides six IR ports. Ports 1, 2, and 3 can be reconfigured independently for serial communication. If not used for serial, they can be used for IR. Connect a serial device to the controller using the Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B, sold separately). 1 The serial ports support many different baud rates (acceptable range: 1200 to 115200 baud for odd and even parity). The serial ports do not support hardware flow control. 2 See Knowledgebase article #268 (kb.control4.com/questions/268) for pinout diagrams. 3 To configure a port for serial or IR, make the appropriate connections in your project using Composer Pro. See the Composer Pro User Guide for details. Note: The serial ports can be configured as straight-through or null with Composer Pro. Serial ports by default are configured straight-through and can be changed in Composer by selecting the option Enable Null-Modem Serial Port (1/2/3). Set up IR emitters Your system may contain third-party products that are controlled through IR commands. The included IR emitters can send commands from the controller to any IR-controlled device. 1 Connect one of the included IR emitters into an IR OUT port on the controller. 2 Remove the adhesive backing from the emitter (round) end of the IR emitter and affix it to the device to be controlled over the IR receiver on the device. Set up external storage devices You can store and access media from an external storage device, for example, a USB drive, by connecting the USB drive to the USB port and configuring or scanning the media in Composer Pro. A NAS drive can also be used as an external storage device, see the Composer Pro User Guide (ctrl4.co/cpro-ug) for more details. Note: We support only externally powered USB drives or solid-

state USB drives (USB thumb drives). USB hard drives that do not have a separate power supply are not supported. Note: When using USB storage devices on an EA-3 Controller, you can use only one partition with a 2TB maximum size. USB storage devices should be formatted FAT32. This limitation also applies to USB storage on all other controllers. Composer Pro driver information Use Auto Discovery and SDDP to add the driver to the Composer project. See the Composer Pro User Guide for details. Troubleshooting Reset to factory settings Caution! The factory restore process will remove the Composer project. Back up the project with Composer Pro before you start the factory restore process To restore the controller to the factory default image:

1 Insert a straightened paper clip into the small hole on the back of the controller labeled FACTORY RESTORE. 2 Press and continue to hold the FACTORY RESTORE button, the controller will reset and the caution LED will turn solid red. 3 Continue to hold the button for about five to seven seconds until the caution LED blinks twice yellow. After the caution LED blinks twice yellow, release the button and the factory restore process will begin. The caution LED will blink orange while the factory restore is running. When complete, the caution LED turn offs and the device will reset. Copyright 2015, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Store, 4Sight, Control My Home, Everyday Easy, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/

or other countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. A 200-00381-A 2015-07-06 DH control4.com | 888.400.4070 Regulatory Compliance & Safety Information for Control4 Model C4-EA3 Electrical Safety Advisory Scurit lectrique consultatif Important Safety Information Informations de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. fabricant. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 13. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement , ou s'il est tomb. 15. Use the circuit breaker to disconnect the apparatus from the AC mains. The circuit breaker shall remain readily accessible. 15. Utiliser le disjoncteur pour dconnecter l'appareil de l'alimentation secteur. Le disjoncteur doit rester facilement accessible. 16. To completely disconnect unit power from the AC mains, turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. 16. Pour couper entirement l'alimentation appareil de l'alimentation secteur, teignez le disjoncteur. Pour rtablir le courant, mettez le disjoncteur aprs les consignes de scurit et des lignes directrices. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Partie 15, sous-section B Unintentional Dclaration sur les interfrences des missions Cet quipement a t test et jug conforme aux limites tablies pour un dispositif numrique de classe B, conformment la Partie 15 des rglements de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles lorsque l'quipement est utilis dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de l'nergie rayonnent frquence et, s'il n'est pas install et utilis conformment aux instructions, il peut causer des interfrences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en mettant l'quipement hors et sous tension, l'utilisateur est encourag essayer de corriger l'interfrence par une ou plusieurs des mesures suivantes:

Rorienter ou dplacer l'antenne de rception. Augmenter la distance entre l'quipement et le rcepteur. Connecter l'quipement une prise sur un circuit diffrent de celui sur lequel le rcepteur est branch. Consulter le revendeur ou un technicien radio / tlvision qualifi pour obtenir de l'aide. This device complies with part 15 of the FCC rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: R33C4EA3 IC: 7848A-C4EA3 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: R33C4EA3 IC: 7848A-C4EA3 Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. This radio transmitter (WiFi Module Model: AEH-AR9462 certified under IC:20662-AEHAR9462 and C4-EA3 Zigbee transceiver certified under IC:7848A-C4EA3) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Manufacturer: OxfordTec Model: WAND2DBI-SMA Maximum Gain: 2.4-2.5 GHz (2 dBi), 4.9-5.825 GHz (3 dBi) Manufacturer: Cirocomm Technology Model: 03A153040379240 Maximum Gain: 2.4-2.5 GHz (-5 dBi) Le prsent metteur radio (identifier le dispositif par son numro de certification) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Fabricant: OxfordTec Modle: WAND2DBI-SMA Gain maximum: 2.4-2.5 GHz (2 dBi), 4.9-5.825 GHz (3 dBi) Fabricant: Cirocomm Technology Modle: 03A153040379240 Gain maximum: 2.4-2.5 GHz (-5 dBi) RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The equipment should only be used or installed at locations where there is normally greater than a 30cm separation between the antenna and all persons. This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites FCC / IC d'exposition aux rayonnements dfinies quatrime opration appareils portables transmettre dans un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. L'quipement ne doit tre utilis ou install des endroits o il est normalement suprieure une sparation de 30 cm entre l'antenne et toute personne. Cet metteur ne doit pas tre co-localiss ou fonctionnement en conjonction avec une autre antenne ou un autre metteur. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser cet quipement. European Compliance (English) Conformity of the equipment with the guidelines below is attested by the application of the CE mark. Manufacturers Name:

Manufacturers Address:

CE Declaration of Conformity CONTROL4 CORPORATION 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM Home Controller Contol4 C4-EA3 Product Name(s):

Brand:

Model(s):

Product Standard(s) to which Conformity of the Council Directive(s) is declared:

EMC - 2014/30/EU Electromagnetic Compatibility (EMC) Directive:

(Emissions) EN 55022:2010, (Immunity) EN 55024:2010, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2006 + A1:2009 + A2:2009 & EN 61000-3-3:2008 Safety 2006/95/EC Low Voltage Directive (LVD):

EN 60950-1:2006/A11:2009/A1:2010/A12:2011 Radio - 2014/53/EU Radio Equipment Directive (RED):

EN 300 328 V1.9.1 ErP - 2009/125/EC Energy-related Product Directive. RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: December 22, 2015 Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer Conformit europenne (French) Conformit de l'quipement avec les directives ci-dessous est atteste par l'apposition de la marque CE. Dclaration de conformit CE Le nom du fabricant:

Le fabricant Adresse:

Nom Reprsentant de l'UE: CONTROL4 EMEA LIMITED UE reprsentant Adresse: Unit3, GREEN PARK CENTRE D'AFFAIRES CONTROL4 CORPORATION 11734 S. LECTION Road Suite 200 SALT LAKE CITY UT 84020 USA Sulton-ON-THE FOREST YORK YO61 IET, ROYAUME-UNI Accueil Controller Contol4 C4-EA3 Nom (s) de produit:

Marque:

Modle (s):

Produit standard (s) dont la conformit de la directive du Conseil (s) est dclare:

EMC - 2014/30 / "compatibilit lectromagntique (CEM)" UE:

(missions) EN 55022: 2010, (immunit) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2: 2006 + A1: 2009 + A2: 2009 et EN 61000-3-3: 2008 Scurit - 2006/95 / CE "Directive Basse Tension (DBT)":

EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 Radio - 2014/53 / UE directive quipement radio (RED):

EN 300 328 V1.9.1 ErP - 2009/125 / CE lies l'nergie directive sur les produits. RoHS - 2011/65 / UE limitation de l'utilisation de certaines substances dangereuses dans les quipements lectriques et lectroniques (EEE) et DEEE - 2002/96 / CE Dchets d'quipements lectriques et lectroniques (EEE). Nous, soussigns, dclarons que l'quipement indiqu ci-dessus est conforme aux directives et normes ci-dessus. Date de publication 22 Dcembre, ici 2015 Reprsentant lgal Signature Roger Midgley Ingnieur de conformit rglementaire Sr. European Compliance (German) Die Konformitt mit den folgenden Richtlinien wird durch die Anwendung des CE-Kennzeichen besttigt. CE-Konformittserklrung Home Controller Contol4 C4-EA3 Control4 CORPORATION 11734 S. WAHL ROAD SUITE 200 SALT LAKE CITY UT 84020 USA Control4 EMEA LIMITED Unit3, GREEN Park Geschftszentrum Sulton-ON-THE FOREST YORK YO61 IET, VEREINIGTES KNIGREICH Name des Herstellers:

Adresse des Herstellers:

EU-Vertreter Name:

EU-Vertreter Adresse:

Produkt-Name (n):

Marke:

Modell (e):

Produkt-Norm (en), um die Konformitt der Richtlinie (n) deklariert ist:

EMC - 2014/30 / EG "Elektromagnetische Vertrglichkeit (EMV) Die Richtlinie":

(Emissionen) EN 55022: 2010, (Immunitt) EN 55024: 2010, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 und EN 61000-3-

3: 2008 Sicherheit - 2006/95 / EG "Niederspannungsrichtlinie (LVD)":

EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 Radio - 2014/53 / EU ber Funkanlagen-Richtlinie (RED):

EN 300 328 V1.9.1 ErP - 2009/125 / EG Energiebezogene Produktrichtlinie. RoHS - 2011/65 / EU zur Beschrnkung der Verwendung bestimmter gefhrlicher Stoffe in Elektro- und Elektronikgerten (EEE) & WEEE - 2002/96 / EG Richtlinie ber Elektro- und Elektronikgerten (EEE). Wir, die Unterzeichneten, erklren hiermit, dass das oben angegebene Gert zu den oben genannten Richtlinien und Normen. Ausstellungsdatum: 22. Dezember 2015 Gesetzlicher Vertreter Stempel, Unterschrift Roger Midgley Sr. Regulatory Compliance-Ingenieur Conformit Europea (Italian) Conformit del materiale con le linee guida qui sotto attestata dall'applicazione del marchio CE. Dichiarazione di conformit CE Casa controller Contol4 C4-EA3 Sulton-ON-THE FOREST YORK YO61 IET, REGNO UNITO Control4 CORPORATION 11734 S. ELEZIONI STRADA SUITE 200 SALT LAKE CITY UT 84020 Stati Uniti d'America Nome del produttore:

Indirizzo del produttore:

UE Nome Rappresentante: Control4 EMEA LIMITED UE Indirizzo Rappresentante: Unit3, GREEN PARK BUSINESS CENTRE Nome del prodotto (s):

Marca:

Modello (s):

Prodotto standard (s) a cui conformit della direttiva del Consiglio (s) dichiarato:

EMC - 2014/30 / UE "Compatibilit elettromagnetica (EMC)":

(Emissioni) EN 55022: 2010, (immunit) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 e EN 61000-3-3: 2008 Sicurezza - 2006/95 / CE "Direttiva bassa tensione (LVD)":

EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 Radio - 2014/53 / Direttiva sulle apparecchiature radio dell'UE (RED):

EN 300 328 V1.9.1 ErP - 2009/125 / CE Energy legati direttiva sui prodotti. RoHS - 2011/65 Limitazione / UE dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche (AEE) e RAEE - 2002/96 / CE sui rifiuti di apparecchiature elettriche ed elettroniche (AEE). I sottoscritti, dichiariamo che l'apparecchiatura specificata in precedenza conforme alle direttive e norme di cui sopra. Data di pubblicazione: 22 dicembre 2015 Rappresentante legale Firma Roger Midgley Suor Conformit alle normative Ingegnere Conformidad Europea (Spanish) La conformidad de los equipos con las siguientes pautas es atestiguado por la aplicacin de la marca CE. Declaracin de conformidad CE Control4 EMEA LIMITED Controlador Inicio Contol4 C4-EA3 Sulton-EN-EL BOSQUE YORK YO61 IET, REINO UNIDO Control4 CORPORACIN 11734 S. ELECCIN Road Suite 200 SALT LAKE CITY UT 84020 EE.UU. Nombre del fabricante:

Direccin del fabricante:

UE Nombre Representante:

Direccin Representante de la UE: Tema 3., VERDE PARQUE EMPRESARIAL CENTRO Nombre (s) del producto:

Marca:

Modelo (s):

Producto estndar (s) a la que la conformidad de la Directiva del Consejo (s) se declara:

EMC - 2014/30 / UE "Directiva de compatibilidad electromagntica (EMC)":

(Emisiones) EN 55022: 2010, (inmunidad) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 y EN 61000-3-3:

2008 Seguridad - 2006/95 / CE "Directiva de Baja Tensin (LVD)":

EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 Radio - 2014/53 / Directiva de Equipos de Radio de la UE (RED):

EN 300 328 V1.9.1 ErP - 2009/125 relacionados con energa / CE Directiva del producto. RoHS - 2011/65 restriccin del uso de ciertas sustancias peligrosas en equipos electrnicos (AEE) y WEEE elctricos y / UE - 2002/96 / CE de Residuos de Aparatos Elctricos (AEE) y electrnicos. Nosotros, los abajo firmantes, declaramos por la presente que el equipo anteriormente mencionado se ajusta a las directrices y estndares anteriores. Fecha de emisin: 22 de diciembre 2015 Representante legal Firma Roger Midgley Ingeniero Sr. Cumplimiento de la normativa Conformidade Europeia (Portuguese) Conformidade do equipamento com as diretrizes abaixo atestada pela aplicao da marca CE. Declarao de Conformidade CE Control4 EMEA LIMITED Incio Controlador Contol4 C4-EA3 Sulton-ON-THE FOREST YO61 IET YORK, REINO UNIDO Control4 CORPORATION 11734 S. ELEIO ROAD SUITE 200 SALT LAKE CITY UT 84020 EUA Nome do fabricante:

Do fabricante Endereo:

Representante da UE Nome:

Representante da UE Endereo: UNIT3, GREEN PARK CENTRO DE NEGCIO Nome (s) produto:

Marca:

Modelo (s):

Padro do produto (s) a que Conformidade da Directiva do Conselho (s) declarado:

EMC - 2014/30 / UE "Compatibilidade Electromagntica (EMC)":

(Emisses) EN 55022: 2010, (Imunidade) EN 55024: 2010, EN 301 489-1 v1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2 : 2006 + A1: 2009 + A2: 2009 e EN 61000-3-3: 2008 Segurana - 2006/95 / CE "Directiva de Baixa Tenso (LVD)":

EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 Rdio - 2014/53 / UE Directiva equipamento de rdio (RED):

EN 300 328 v1.9.1 ERP - 2009/125 relacionados Energy-/ CE Directiva do produto. RoHS - 2011/65 / UE Restrio do Uso de Certas Substncias Perigosas em Equipamentos Elctricos e Electrnicos (EEE) e WEEE - 2002/96 / EC de Resduos de Equipamentos Elctricos e Electrnicos (EEE). Ns, abaixo-assinado, declaro que o equipamento especificado acima est em conformidade com as diretrizes e normas acima referidas. Data de Emisso: 22 de dezembro de 2015 Representante legal Assinatura Roger Midgley Sr. Engenheiro Conformidade Regulatria Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright 2016 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00441 Rev A, 12/22/2015