Folding-Method:
TP7 7 Touch Panel User Interface Quick Install Guide English 150 150 150 150 Job: Universal Manual Size: 150 x 150 mm folded 07/30/2014 -> Final print pdf ELAN & Niles & SpeakerCraft Quick Install Guide TP7 8 pages each - Format: 150 x 300 mm ( Metric !! ) Final Print pdf / Rev B English only 07/30/2014 - WE Questions?
Juergen 707 - 778 - 5826 P/N 9901341 REV. B 07/2014 0 0 3
+
Folded size:
150 x 150 mm Open:
600 mm wide x 300 mm high No bleed TP7 7 Touch Panel User Interface Quick Install Guide English 9901341_Rev-B_Universal_TP7_QSG_0730_PRINT.indd 1-4 7/30/14 9:59 AM 2 Powering up the TP7 4 Setting screen orientation Important Safety Instructions Once installation is complete, press the Power button located on top of the TP7 and allow the unit to boot up.
- If connected to a wired Ethernet switch the TP7 will aquire a network address via DHCP and automatically connect to the system. The TP7 is shipped pre-confi gured for landscape orientation. To change orientation:
Tap the POWER button 10 times in quick succession Follow the on-screen instructions to re-orient the screen
- If the TP7 does not detect a wired Ethernet connection and the WiFi radio has never been confi gured you will be presented with the Network Confi guration Utility interface. To complete the network confi guration please refer to the most current training documentation for your system. Power 3 Removing the TP7 Using two hands grasp it on each side or the top and bottom and pull straight out from the wall. It will require approx. 10lbs of force to remove it from the bracket. 5 RESET The recessed RESET button has two functions Mounting Bracket Mounting Bracket Top of 2 Gang Box Dry Wall TP7 Frame the factory default settings. A tap of the button will reset all network confi guration Press and hold the button for 15 seconds completely restores CAUTION:
Neither of these actions can be reversed. Recessed Reset Switch LAN + Power over Ethernet Recessed Reset Switch Paper Clip 9901341_Rev-B_Universal_TP7_QSG_0730_PRINT.indd 5-8 1. Read, understand and follow ALL safety and installation instructions included in this manual. Failure to follow the included documentation may damage the product and will void manufacturers warranty. 2. Follow ALL installation guidelines included with the product. Installation of the product in high humidity environments, in close proximity to heat sources and /or non-recommended locations WILL impede, interfere and/or damage the intended operation of the product 3. Only use attachments and accessories which have been specifi ed for use by the manufacturer. 4. The use of abrasive, liquid or solvent based cleaning fl uids WILL damage the product. Please refer and follow all Product Care instructions included with the product. 5. Product Servicing may ONLY be completed by authorized or certifi ed service centers & personnel. For a complete list of product servicing options, please follow instructions included in the product documentation and /or contact original manufacturer for details. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. FCC and IC Information:
This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions:
1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC and IC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. Informations concernant lexposition aux frquences radio (RF):
La puissance de sortie mise par lappareil de sans l est infrieure la limite `exposition aux frquences radio dIndustry Canada (IC). Utilisez lappareil de sans l de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites dexposition aux RF dIC dans des conditions dexposition des appareils mobiles (antennes sont suprieures 20 cm partir du corps dune personne). Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: (519) 763-4538. TP7 7 Touch Panel User Interface Quick Install Guide English Thank you for including the TP7 as part of the user interface strategy for your customer. The TP7 has been designed to provide years of trouble free operation when wired and installed properly. The TP7 has been designed for installation in low humidity indoor environments and should never be installed outdoors or in high humidity areas. Included in the box 1ea TP7 touch panel 1ea TP7 mounting bracket 4ea Mounting screws 1ea DC power connector Introduction To install the TP7 you will also need a standard 2 gang US junction box or low voltage bracket. Speci cations Dimensions Microphone Speaker Camera Display Network Connections LAN/PoE Power USB Audio Out Overall 8w x 5h Mounting Depth 1 Dual Digital Beam Forming Far Field Pickup 2w integrated 640 x 480 7 800 x 480 10/100 Ethernet 802.11 B/G/N WiFi RJ-45 2 pin Phoenix USB Type A 1/8 stereo (Future Use) Power Requirements Direct 12v DC 350mA PoE IEEE 802.3at, 13w maximum draw
(@44 V /350 mA max) 2014 Core Brands, LLC. All rights reserved. Core Brands,LLC,aNortek company. P/N 9901341 Rev. B 07/2014 7/30/14 9:59 AM TP7 Overview Power Camera Microphone Status LED Proximity Sensor b. Rough-In e. Installing the TP7 Bracket 12v Power Supply The TP7 has been designed to mount to a US standard 2 gang box or low voltage bracket.
- The TP7 is snap fit into the box/bracket and requires approximately 10lbs of force to remove it from the wall. Ensure that the mounting method you are using is compatible with these requirements. The TP7 includes a mounting bracket that MUST be used. Using the included screws mount the bracket onto the 2 gang box or low voltage bracket and verify that the bracket is level before tightening the screws. The mounting bracket is designed to level out uneven wall surfaces allowing the TP7 to fit securely on most any surface. Note that uneven surfaces will create a gap between the back of the panel and the wall this is normal. Do not tighten the mounting bracket so as to distort its shape as this will create issues with properly seating the TP7 in the bracket. Speaker DC Power Input LAN + Power over Ethernet Recessed Reset Switch USB Recessed Reset Switch Audio Out
(Future Use) New Const. Box Old Work Box New Const. Low Volt Bracket Old Work Low Volt Bracket By utilizing a 12v power supply (not included) to power the TP7 you may provide power locally or remotely. If powering locally be sure to run the wire through the wall in accordance with local codes. If powering remotely be sure to use wire of adequate gauge for the length of the run. Verify the polarity of your power supply prior to termination and ensure the power supply is not connected to a power source. Strip approx. of insulation from the wire and observing the correct polarity, terminate the wire into the supplied connector and tighten firmly. Be sure to twist the wires before inserting so that no strands escape the connector. Inspect the termination to verify that the wire is securely retained by the connector and no strands have escaped the barrier. Plug the connector into the TP7. F-2 Front of Mounting Bracket Back of TP7 TP7 Touch Panel Line in wall Phoenix Type Connector Planning the installation c. Landscape Mounting f. Connecting the TP7 to power g. Connecting Ethernet The TP7 is designed to wall mount in either Portrait or Landscape orientation. Ensure there is adequate wall space for the TP7 and that the surface is relatively smooth. The TP7 requires a minimum mounting depth of 1 (4.5 cm) from the front surface plus room for wire. Ensure that adequate depth is available. Power may be supplied by Power Over Ethernet (PoE) or by a 12v DC power supply (not included). PoE must meet the IEEE 802.3af standard. Direct power via a 12v DC external power supply requires a minimum current output of 350mA. The TP7 connects to the local network via Ethernet or Wi-Fi. When utilizing Wi-Fi you must ensure that there is adequate Wi-Fi coverage at the mounting location. Install the 2 gang box or bracket in its normal orientation with mounting screw holes at the top and bottom. The box is exactly centered with the touch panel for your convenience. 2 Gang Box Power TP7 F-1-A The TP7 is designed to be powered over the Ethernet connection (PoE) or by connecting a 12v power supply (not included), but not both. If both the PoE and a 12v power supply are connected the TP7 will draw power from the 12v source. PoE Connection PoE connection requires that IEEE 802.3af standard (13w maximum draw @44 VDC/350mA max) is met. Utilize a network switch or PoE injector that meets this standard. Connect the TP7 using a standard T568A or T568B Ethernet cable from the network switch to the LAN/PoE jack. If you have terminated your own CAT 5e/6/7 cable use a tester to ensure that both ends have been properly terminated. 1 Installing the TP7 a. Mounting height d. Portrait Mounting Install the 2 gang box or bracket rotated 90 - with the mounting screw holes on the left and right sides. The box is exactly centered in the touch panel for your convenience. Depending on how tall your homeowner is, it is recommended to locate the center of TP 7 between 57- 65 (145 cm -165 cm) above the finished floor. 2 Gang Box 165 cm / 65 145 cm / 57 Power TP7 To TP7 F-1-B PoE Injector Network Switch When not utilizing PoE, but you have a physical network connection available it is recommended that you connect the TP7 directly to the network switch. Utilizing a T568A or T568B network cable connect to the LAN/PoE jack. If you have terminated your own CAT 5e/6/7 cable use a tester to ensure that both ends have been properly terminated. h. Mounting the TP7 The TP7 is held into the mounting bracket by spring steel tabs. Orient the TP7 with the POWER button at the top right for landscape mounting or the top left for portrait mounting. To complete the installation simply grasp the TP7 on the edges and press firmly on to the bracket until it is seatled. CAUTION: DO NOT PRESS DIRECTLY ON THE SCREEN when installing on to the mounting bracket. Press only on the frame edges. Mounting Bracket Top of 2 Gang Box Mounting Bracket TP7 Touch Panel PoE Network Switch Dry Wall TP7 Frame 9901341_Rev-B_Universal_TP7_QSG_0730_PRINT.indd 9-12 7/30/14 9:59 AM