2M FHD IP INS Cube Camera Users Manual_Install Part Ver. 1.0 / 2022.11 Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference. Contents INTRODUCTION 03 06 07 08 Important Safety Informaon Specicaon Product & Accessories Part Name INSTALLATION 09 11 12 Installaon Cabling Inserng / Removing an SD Memory Card SPECIFICATION 13 14 Dimension FCC Instrucons Safety Instruction These instrucons are intended to ensure that the user can use the product correctly to avoid danger or property loss. If the product is not funconing properly or damaged, contact the service center or purchasing oce. Warnings Serious injury or death may be caused if any of these warnings are neglected. Cautions Injury or equipment damage may be caused if any of these cautions are eglected. POWER POWER 1. Use only standardized adapters wrien in the manual. 1. Use the power line aer xing it rmly to the power connecon Incorrect connecon of the power source can cause re, electric shock, or failure. 2. If there is smoke or a strange smell from the power source, disconnect the power immediately and contact the service center or purchasing oce. If you connue to use it as it is, it can cause re and electric shock. 3. Disconnect the power plug from the outlet before connecng to the power terminal block. INSTALLATION 1. 2. Install it according to the temperature and humidity environment suitable for the product specicaons. Otherwise, it can cause re and electric shock. Thunder and lightning can cause problems with the camera. When installing, be careful to minimize damage caused by lightning such as grounding. 3. Do not place conducve materials (drivers, coins, metal scks, etc.) and water-lled containers on the camera. It causes injuries caused by re, electric shock, and falling. 4. If you want to move the installed product, turn o the power and move it or reinstall it. Otherwise, it can cause re and electric shock. 5. Do not install it in places where there is a lot of moisture, dust, soot, etc. It causes re and electric shock. 6. Avoid places where direct sunlight comes in or where heat comes out, such as heang appliances. It causes re and electric shock. CLEANING 1. Do not spray water directly on each part of the product when cleaning. It causes re and electric shock. terminal. Incomplete connecon can cause a re. 2. Do not extend the adapter output cable. If you need to install the power cable extension, please contact the service center. 3. Use insulated power for PoE connected external power. INSTALLATION 1. It is recommended not to touch the lens when installing the product as the factory ships with a focus adjustment completed during the manufacturing compleon inspecon phase. 2. Avoid installing cameras facing bright lights like sunlight. Causes damage to the image sensor. 3. Make sure it safe and securely when installing camera on the wall or ceilling. This can cause injury by the fall. 4. Do not connect mulple cameras to one adapter. Excess capacity causes abnormal heat and re. 5. Wear protecve gloves when installing/uninstalling the camera. This causes burns caused by high temperature on the surface of the product. 6. Don't drop or shock the product. Please stay away from places where vibraon is severe or magnet types are present. 7. Install it in a well-venlated place. This can cause re and failure. CLEANING 1. Wipe the contaminated surface with a clean, so, dry cloth or wet the so, dry cloth to prevent water from owing, then wipe the contaminated area. Installaon and Use Precauons 1. The baery (baery pack or equipped baery) must not be exposed to excessive heat such as sunlight, re, etc. 2. Do not disassemble the camera at your discreon. 3. If you forcefully install the product with excessive force, malfuncon can damage the camera. 4. Do not punch or shake the camera and be careful not to damage the camera with careless storage or malfuncon. 5. Be careful not to install the camera in a rainy or humid place, and do not leave it in a wet place. 6. Installing or using the product in water can cause serious product failure. 7. Do not install the product if there is chemical or vapor in the place where the product is installed, or if it can be generated. 8. Be careful not to get chemicals on the surface of the product when installing the product. Chemical solvents such as cleaning agents and adhesive components can cause fatal damage to the surface of the product. 9. Do not install it near the kitchen or cooking table as edible oil such as soybean oil can also cause product damage and deformaon. It can cause product damage. 10. Be careful not to get foreign substances on the Micro SD card terminal. If there is any foreign substance, wipe it with a so cloth. 11. Data will not be saved at the end of the life of the Micro SD card. In this case, purchase a new Micro SD card. 12. Moisture may occur in the glass of the camera when the new product box is opened (or when the product is inially running). The generated moisture is removed by a Gore vent aached to the camera within hours of the power connecon. 13. For products enclosed with a desiccant or card-type absorbent, please install it according to the manual. 14. Use only with cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. 15. Unplug this apparatus when a cart is used. Use cauon when moving the cart/apparatus combinaon to avoid injury from p-over. Disposal of Old Appliances 1. The symbol marked in the product, will follow and covered by the Europe Direcve 2002/95/EC. 2. All electornic disposal of waste is dierenct by the government or locally, so so it need to check. 3. The correct disposal of your old appliance will help prevent potenal negave consequences for the environment and human health. 4. For more detailed informaon about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful interference to radio communicaons. Operaon of this equipment in a residenal area is likely to cause harmful interference in which case the user will be required to correct the interferenece at his own expense. Specicaon FEATURES Opmized Mulple Prole Streaming ROI(Region of Interest) Various web plug-in Advanced built in ISP Fluid integraon way Double Scan sensor with advanced built in ISP A true all-in-one soluon IMAGE Max. Image Resoluon 1920 x 1080 Frame Rate 60Hz : 30fps Digital Noise Reducon 3D DNR Wide Dynamic Range Ture WDR SPECIFICATION CAMERA Image Seng Rotate mode, Saturaon, Brightness, Contrast, Sharpness, AGC, ROI PHYSICAL Working Temperature
-20C - 50C (-4F - 122F) Humidity 90% max Dimensions (VxH) 87.6mm x 114mm x 72.1mm Image Sensor 1/2.8" Progressive Scan CMOS Weight 297g Lens 2.8mm, F1.6 Min. Illuminaon 0.035Lux, AGC On : 0Lux with IR (F1.6) IR Range Angle of View PIR Range Day/Night Up to 10m 110 Up to 10m, 120 Angle of View IR cut lter with auto switch ELECTRICAL Power Supply 12V DC 10%, PoE 48 V (802.3af) Power Consumpon 12V DC 5.0W, PoE 48 V (802.3af) 11.5W INTERFACE Shuer Speed 1/15s - 1/32,000s Communicaons 1 RJ45 10M/100M Ethernet Port COMPRESSION STANDARD Video Compression H.264, H.265, MJPEG Video Bit Rate 100Kbps - 10Mbps Audio Compression G.711 FUNCTIONS Alarm Triggers Local Storage Security Protocols Moon Detecon, Network Disconnect, IP address conict, Storage excepon, Temperature Crical, PIR Detecon Built-in Micro SD, SDHC, SDXC card slot, Up to 128GB One-key reset, Flash-prevenon, Dual Stream, Password protecon, Privacy mask, IP address ltering, Anonymous access TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, NTP, UPnP
, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour Audio Input Built-in Microphone Audio Output Built-in Speaker Alarm out (NO/NC) Tamper Alarm (Switch) 1 1 WI-FI Wireless Standard IEEE802.11b, 802.11g, 802.11n Frequency Range 2.4 GHz ~ 2.4835 GHz Channel Bandwidth 20MHz, 40MHz Support Protocols Security 802.11b : CCK, QPSK, BPSK, DSSS ;
802.11g/n : OFDM 64/128bit WEP, WPA/WPA2, WPA-PSK/ WPA2-PSk, WPS Wireless Range 20m (Dependent Upon Environment) CERTIFICATIONS FCC, CE Introducon -
Product & Accessories Camera Cable Hole. Mounng Bracktet Mounng Template Mounng Screw (4x35mm)
& Plasc Anchor-4pcs Dc Plug Jack Screw 1pc Introducon -
Part Name Mic Lens LED PIR Sensor Speaker SD Card Slot DC 12V Port Illuminaon Sensor Lan Port Alarm Terminal Port Reset / WPS Installaon -
Installaon Before installing your camera, you have to read the following cauons. 1. You have to check whether the locaon can bear ve mes of the weight of your camera. 2. Dont let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it may cause a breakdown or re. 3. When installing your camera, dont allow any person to approach the installaon site. If you have any valuable things under the place, move them away. Note : Before installaon, press both buons on the camera and remove the camera and bracket. 2 1 1 3 When you Install it on the wall When you Install it on the corner 1 2 Use a mounng template to punch holes in the wall. Install the mounng bracket on the perforated wall using two mounng screws. If not using Mounng bracket, use the mounng screw to x the 4 checked parts. 3 Install the mounng bracket on the perforated wall using four mounng screws. Installaon -
Installaon Installaon A Installaon B Camera Mounng Bracket Camera Mounng Bracket 4 6 4 5 6 5 Refer to installaon A ,B images and assemble according to the direcon. 5 Fasten the camera to the mounng bracket xed to the wall. 4 Adjust in the desired direcon. (UP arrow up) 6 Tighten the screws to prevent the camera movement. 7 5 8 7 Connect the Cable. Use the DC plug jack included in the accessory when connecng the DC12V. 8 Press both side buons to combine, then ghten the boom of product with the provided accessory screw. Reset to the Factory Default Press the reset buon for 5 seconds to return the setup to the factory default. Warning:
If you press the Reset buon, you will lose all seng data. If needed, please, make a note for further installaon. Installaon -
Cabling 2 1 T1 T2 +12V GND N.O COM N.C 1 2 3 4 5 6 7 T1 (TAMPER SWITCH) T2 (TAMPER SWITCH)
+12V (DC12V) GND (Ground) N.O (NOMAL OPEN) COM (Common) N.C (NOMALCLOSE) 3 Relay Status Camera Power Off Camera Power On N.O N.C 3 1 Power Connecon Please, check the voltage and current capacity of rated power carefully. Rate Power DC 12V Power Consumption DC : 6.4W PoE : 6.8W PoE IEEE 802.3af Class3 2 Network Connecon Connect the crossover cable into the RJ-45. Installaon -
Inserng/Removing a SD Memory Card The memory card is an external data storage device that has been developed to oer an enrely new way to record and share video, audio, and text data using digital devices. Micro Recommended SD Card Specicaon (Not Included)
- Type: Micro SD (SD/SDHC/SDXC)
- Manufacturer: SanDisk, Samsung, Transcend, Micron
- Capacity: 4GB~128GB
- Class: UHS-I U3 Class 10 New Micro SD card over 64GB must be formaed on the rst use. 1 Inserng an SD Memory Card Insert the SD card in the arrow direcon. Dont insert the SD memory card while its upside down by force. Otherwise, it may damage the SD memory card. 2 Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the slot when released. If you have saved data in the SD memory card, removing the SD memory card prior to seng record to OFF will cause damage to the data stored in the card. Specicaons -
Dimension Unit: mm 114 87.6 72.1 60 96.8 FCC Instrucons -
FCC ID: 2AX2S-INS-CUBE FCC Instrucons FCC ID: 2AX2S-INS-CUBE FCC Compliance Statement(Part 15.19 (3)) This device complies with part 15 of the FCC rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, ncluding interference that may cause undesired operaon. FCC Interference Statement(Part 15.105) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Cauon Any changes or modicaons not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier. FCC Radiaon Exposure Statement (Part 2.1091) This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmier must not be co-located or operang in conjuncon with any other antenna or transmier.