all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Part 1 | Users Manual | 3.31 MiB | August 09 2004 | |||
1 |
|
Part 2 | Users Manual | 3.52 MiB | August 09 2004 | |||
1 | Cover Letter(s) | August 09 2004 | ||||||
1 | Cover Letter(s) | August 09 2004 | ||||||
1 | External Photos | August 09 2004 | ||||||
1 | Internal Photos | August 09 2004 | ||||||
1 | ID Label/Location Info | August 09 2004 | ||||||
1 | Operational Description | August 09 2004 | ||||||
1 | Cover Letter(s) | August 09 2004 | ||||||
1 | RF Exposure Info | August 09 2004 | ||||||
1 | ID Label/Location Info | August 09 2004 | ||||||
1 | Test Report | August 09 2004 | ||||||
1 | Test Setup Photos | August 09 2004 |
1 | Part 1 | Users Manual | 3.31 MiB | August 09 2004 |
D-Link AirPlus GTM DWL-G730AP 802.11g/2.4GHz Wireless Pocket Router/AP Manual Building Networks for People Contents Package Contents ................................................................................3 Introduction............................................................................................4 Wireless Basics ....................................................................................6 Hardware Overview ...............................................................................8 Getting Started in AP Mode ...................................................................9 Getting Started in Client Mode .............................................................10 Getting Started in Router Mode ........................................................... 11 Using the Configuration Utility in AP Mode ...........................................12 Using the Configuration Utility in AP Client Mode .................................24 Using the Configuration Utility in Router Mode .....................................35 Networking Basics ..............................................................................60 Technical Specifications ......................................................................73 Contacting Technical Support ..............................................................76 Warranty and Registration ...................................................................77 2 Package Contents Contents of Package:
D-Link AirPlusTM G DWL-G730AP 802.11g/2.4GHz Wireless Pocket Router/AP
Power Supply - 5V DC, 1.2A
Manual on CD
Quick Installation Guide
Ethernet Cable
USB Power Cable
Travel Case If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DWL-G730AP will cause damage and void the warranty for this product. System Requirements:
Computer with Windows XP/2000/Me operating system with an installed Ethernet adapter Internet Explorer version 6.0 or Netscape Navigator version 7.0, with JavaScript enabled 3 Introduction The pocket-sized DWL-G730AP gives you all the features of a full-size router/access point with pocket-size convenience and portability. Carry it along with you on business trips and vacations, and experience the convenience of wireless networking with your colleagues and family almost anywhere you travel. With 3 different operating modes, the versatile DWL-G730AP can be used as a portable access point, AP client or router. At up to five times the speed of previous wireless devices (maximum wireless signal rate up to 54Mbps*), you can work faster and more efficiently, increasing productivity. With the DWL-G730AP, bandwidth-intensive applications like graphics or multimedia will benefit significantly because large files are able to move across the network quickly. The D-Link AirPlusTM G DWL-G730AP Wireless Pocket Router/AP is an 802.11g high-performance, wireless device that is also compatible with 802.11b devices. It is an ideal way to extend the reach and number of computers connected to your wireless network. The DWL-G730AP is capable of data transfer rates up to 54Mbps*, when used with other D-Link AirPlus G products, and can be integrated into a large network.
*Maximum wireless signal rate based on IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and environmental factors lower actual data throughput rate. 4 Features and Benefits
Up to 5X Faster with AirPlus G Products - maximum wireless signal rate up to 54Mbps.* With increased data rate and capacity, the DWL-G730AP delivers media rich content such as digital images, videos, and MP3 files much faster than standard 802.11b networks.
Fully 802.11b Compatible Fully compatible with the IEEE 802.11b standard and interoperable with all existing 802.11b compliant devices.
Network Security with up to 128-bit WEP Encryption Supports 64/128-bit WEP encryption for a level of security for your data and wireless communication.
Built-in DHCP Server If enabled, it will automatically assign IP addresses to wireless clients on the local network.
Web-based interface for Managing and Configuring Easy-to-use interface independent of the operating system.
*Maximum wireless signal rate based on IEEE Standard 802.11g specifications. Actual data throughput will vary. Network conditions and environmental factors lower actual data throughput rate. 5 Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking brings. A Wireless Local Area Network (WLAN) is a computer network that transmits and receives data with radio signals instead of wires. WLANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. People use WLAN technology for many different purposes:
Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency. Low Implementation Costs WLANs are easy to set up, manage, change and relocate. Networks that frequently change can benefit from WLANs ease of implementation. WLANs can operate in locations where installation of wiring may be impractical. Installation and Network Expansion - Installing a WLAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings. Wireless technology allows the network to go where wires cannot go - even outside the home or office. Scalability WLANs can be configured in a variety of ways to meet the needs of specific applications and installations. Configurations are easily changed and range from peer-to-peer networks suitable for a small number of users to larger infrastructure networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed. Inexpensive Solution - Wireless network devices are as competitively priced as conventional Ethernet network devices. 6 Wireless Basics (continued) Installation Considerations Keep in mind, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1 2 3 4 Keep the number of walls and ceilings between the DWL-G730AP and other network devices to a minimum - each wall or ceiling can reduce your DWL-G730APs range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized. Be aware of the direct line between network devices. A wall that is 1.5 feet thick
(.5 meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. Building materials can impede the wireless signal - a solid metal door or aluminum studs may have a negative effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise. 7 Hardware Overview Top Panel Power LED: Solid indicates a connection to a good power source. LAN LED: Solid indicates an Ethernet connection. Blinking indicates activity on the Ethernet network. WLAN LED: A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission. Mode Selection Switch:
Used to select AP, client, or router mode. Rear Panel Reset Button:
Used to restore default settings. Receptor for Power Adapter LAN Port This is the connection for Ethernet cables to your Ethernet-enabled device. When in Router mode, this port functions as a WAN port. 8 Getting Started - in AP mode An Example of a Wireless Infrastructure Network 11111 55555 22222 33333 44444 66666 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home (as shown above), please do the following:
You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem Connect the Cable or DSL modem to your broadband router (see the Quick Installation Guide included with your router.) Connect the router to the D-Link AirPlus G DWL-G730AP (in access point mode).
(See the Quick Installation Guide included with the DWL-G730AP.) If you are connecting a desktop computer in your network, you can install the D-Link AirPlus G DWL-G510 wireless PCI adapter into an available PCI slot on your desktop computer.
(See the Quick Installation Guide included with the DWL-G510.) Install the drivers for the wireless Cardbus adapter into a laptop computer.
(e.g, the DWL-G630; See the Quick Installation Guide included with the DWL-G630.) 9 Getting Started - in Client mode An Example of a Wireless Infrastructure Network 22222 33333 11111 44444 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home (as shown above), please do the following:
You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem Connect the Cable or DSL modem to your broadband router (see the Quick Installation Guide included with your router.) Connect the D-Link AirPlus G DWL-G730AP (in client mode) to your laptop.
(See the Quick Installation Guide included with the DWL-G730AP.) 10 Getting Started - in Router mode An Example of a Wireless Infrastructure Network 22222 11111 33333 55555 44444 Please remember that D-Link AirPlus G wireless devices are pre-configured to connect together, right out of the box, with their default settings. For a typical wireless setup at home (as shown above), please do the following:
You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office) Consult with your Cable or DSL provider for proper installation of the modem. Connect the modem to the D-Link AirPlus G DWL-G730AP (in router mode).
(See the Quick Installation Guide included with the DWL-G730AP.) If you are connecting a desktop computer in your network, you can install the D-Link AirPlus G DWL-G510 wireless PCI adapter into an available PCI slot on your desktop computer.
(See the Quick Installation Guide included with the DWL-G510.) Install the drivers for the wireless Cardbus adapter into a laptop computer.
(e.g, the DWL-G630; See the Quick Installation Guide included with the DWL-G630.) 11 Using the Configuration Utility in AP Mode After you have completed the initial installation and the Setup Wizard (as illustrated in the Quick Installation Guide that is included with the DWL-G730AP), and you have selected AP Mode, you can access the configuration menu, at any time, by opening the web-browser and typing in the IP address of the DWL-G730AP. The DWL-G730APs default IP address is shown below:
Open the web browser
Type in the IP address of the DWL-G730AP. (192.168.0.30). http://192.168.0.30 Note: If you have changed the default IP address assigned to the DWL-G730AP, make sure to enter the correct IP address.
Type admin in the User Name field
Leave the Password blank
Click OK The Home>Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard. 12 Using the Configuration Utility in AP Mode (continued) Home > Wireless Hexadecimal digits consist of the numbers 0-9 and the letters A-F ASCII (American Standard Code for Information Interchange) is a code for representing English letters as numbers from 0-127 SSID: (Service Set Identifier) default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting. All devices on the network must be set to the same channel to communicate on the network. Authentication:
Select Open System to communicate the key across the network. Select Shared Key to limit communication only to those devices that share the same WEP settings. Select WPA to select Wi-Fi Protected Access in conjunction with a RADIUS server in your network Select WPA-PSK to select Wi-Fi Protected Access without a RADIUS server. WEP: Select Enabled or Disabled. WEP Encryption: Select 64-bit or 128-bit WEP encryption. Key Type: Select Hexadecimal or ASCII key type Keys 1-4: Input up to four encryption keys. You will select one of these to be the active key. Apply: Click Apply to apply the changes. 13 Using the Configuration Utility in AP Mode (continued) Home > Wireless > WPA SSID: (Service Set Identifier) Default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting. All devices on the network must be set to the same channel to communicate on the network. Authentication:
Select WPA to select Wi-Fi Protected Access in conjunction with a RADIUS server in your network. When WPA is selected fill in the following fields:
RADIUS Server 1 IP: Enter the IP address of the RADIUS server. Port: Enter the Port number here. Shared Secret: Enter the shared secret here. RADIUS Server 2 IP: Enter the IP address of the RADIUS server. Port: Enter the Port number here. Shared Secret: Enter the shared secret here. Apply: Click Apply to apply the changes. 14 Using the Configuration Utility in AP Mode (continued) Home > Wireless > WPA-PSK SSID: (Service Set Identifier) Default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting. All devices on the network must be set to the same channel to communicate on the network. Authentication:
When WPA-PSK is selected fill in the following fields:
Passphrase: Enter the Passphrase here. Confirmed Passphrase: Confirm the Passphrase here. Apply: Click Apply to apply the changes. 15 Using the Configuration Utility in AP Mode (continued) Home > LAN Dynamic IP Address: Select this option if you would like to have an IP Address automatically assigned to the DWL-G730AP by a DHCP server in your network. DHCP stands for Dynamic Host Configuration Protocol. It is a protocol for assigning dynamic IP addresses automatically. With a DHCP Server there is no need to manually assign an IP Address. Static IP Address: Select this option if you are manually assigning an IP address. IP Address: 192.168.0.30 is the default IP address of the access point. Subnet Mask: 255.255.255.0 is the default Subnet Mask. All devices on the network must have the same subnet mask to communicate on the network. Gateway: Enter the IP address of the router in your network. DNS Server:
Enter the IP address of the DNS server. The DNS server translates domain names such as www.dlink.com into IP addresses. IP Address If you need to assign static IP addresses to the devices in your network, please remember that the IP address for each computer or device must be in the same IP address range as all the devices in the network. Each device must also have the same subnet mask. For example: Assign the first computer an IP address of 192.168.0.2 and a subnet mask of 255.255.255.0, the second device an IP address of 192.168.0.3 and a subnet mask of 255.255.255.0, and so on. Note: Devices that are assigned the same IP address may not be visible on the network. 16 Using the Configuration Utility in AP Mode (continued) Home > DHCP DHCP Server: Select Enabled or Disabled. Disabled is the default setting. If you want to use the DWL-G730AP as a DHCP server, to automatically assign dynamic IP addresses on the network, you will select Enabled. Starting IP Address: If you have enabled the DHCP server function, enter the starting point of the IP address range for your network. Ending IP Address: Enter the ending IP address of your IP address range, if you have enabled the DHCP function of the DWL-G730AP. Lease Time: Choose the length of time during which the DHCP function of the DWL-G730AP automatically regenerates the IP addresses to the devices in your network. DHCP Client Table: Lists the devices on your network that are receiving dynamic IP addresses from the DWL-G730AP. 17 Using the Configuration Utility in AP Mode (continued) Advanced > Performance Beacon Interval: Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346. If you experience a high packet error rate, you may slightly increase your fragmentation threshold within the value range of 256 to 2346. Setting the fragmentation threshold too low may result in poor performance. DTIM Interval (Beacon Rate): (Delivery Traffic Indication Message) Enter a value between 1 and 255 (default is 3) for the Delivery Traffic Indication Message (DTIM.) A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. TX Rates: Select the transmission rate for the network. The default setting is Auto. Mode Setting: For utmost speed, select G Mode to include only 802.11g devices in your network. Select Mix Mode to include 802.11g and 802.11b devices in your network. Preamble: Short Preamble is the default setting. (High traffic networks should use the shorter preamble type.) The preamble defines the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) used in communication between the access point and the wireless network adapters. SSID Broadcast: (Service Set Identifier) Enable or Disable (default) the broadcast of the SSID name across the network. SSID is a name that identifies a wireless network. All devices on a network must use the same SSID to establish communication. Antenna Transmit Power: Select the transmission power of the antenna. Limiting antenna power can be useful for security purposes. 18 Using the Configuration Utility in AP Mode (continued) Advanced > Filters Use MAC Filters to allow or deny wireless clients (identified by their MAC addresses) access to the DWL-G730AP. You can manually add a MAC address or select the MAC address from the list of clients that are currently connected to the router (Connected PCs). The default setting is Disabled MAC Filters. MAC Filter List: This list will display the MAC addresses that are in the selected filter. 19 Using the Configuration Utility in AP Mode (continued) Tools > Admin New Password: Enter the new password. Confirm Password:
Re-enter the password to confirm it. Tools > System Save Settings: The current system settings can be saved as a file onto the local hard drive. Load Settings: The saved file or any other saved setting file can be loaded back on the access point. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. Click Load when you have selected the file to be loaded back onto the access point. Restore: You may also reset the DWL-G730AP back to factory settings by clicking on Restore. Make sure to save the units settings before clicking on Restore. You will lose your current settings when you click Restore. 20 Using the Configuration Utility in AP Mode (continued) Tools > Firmware You can upgrade the firmware of the DWL-G730AP on this page. When you click Click here to check... in this window you will be connnected to D-Links website, where you can download the latest firmware update. After you have completed the firmware download to your hard drive, click Browse to browse your local hard drive and locate the firmware to be used for the update. Click Apply. This screen displays the current firmware version, and the current wireless and Ethernet settings of the DWL-G730AP. Status > Device Info 21 Using the Configuration Utility in AP Mode (continued) Status > Log Using the Configuration Menu View Log The DWL-G730AP keeps a running log of events and activities occurring on the AP. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Setting. First Page - The first page of the log. Last Page - The last page of the log. Previous - Moves back one log page. Next - Moves forward one log page. Clear - Clears the logs completely. Log Settings - Brings up the page to configure the logs. Log Settings Not only does the DWL-G730AP display the logs of activities and events, it can be setup to send these logs to another location. The logs can be sent via email to an email account. 22 Using the Configuration Utility in AP Mode (continued) Status> Stats Traffic Statistics The DWL-G730AP keeps statistics of traffic that passes through it. You are able to view the amount of packets that pass through the Ethernet and wireless portions of the network. The traffic counter will reset if the device is rebooted. Connected Wireless PCs List This list displays the MAC addresses of connected PCs and the length of time that they have been connected. Menu Select from this menu for extra help. Status > Wireless Help 23 Using the Configuration Utility in AP Client Mode Whenever you want to configure your network or the DWL-G730AP, you can access the Configuration Menu by opening the Web browser and typing in the IP address of the DWL-G730AP. The DWL-G730AP default IP address is shown at right.
Open the Web browser Type in the IP address of the AP Client (http://192.168.0.30) Note: if you have changed the default IP address assigned to the DWL-G730AP, make sure to enter the correct IP address.
Type admin in the User Name field
Leave the Password blank Click OK Home > Wizard The Home>Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard. 24 Using the Configuration Utility in AP Client Mode (continued) Home > Wireless SSID-
Service Set Identifier
(SSID) is the name designated for a specific wireless local area network
(WLAN). The SSIDs factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Channel-
6 is the default channel. All devices on the network must share the same channel. (Note: The wireless adapters will automatically scan and match the wireless setting.) Wireless Mode-
Select Infrastructure or Ad-Hoc mode. Authentication-
WEP-
Select Open System to communicate the key across the network. Select Shared Key to limit communication only to those devices that share the same WEP settings. Select WPA-PSK to select Wi-Fi Protected Access without a RADIUS server. Wired Equivalent Privacy (WEP) is a wireless security protocol for Wireless Local Area Networks (WLAN). WEP provides secu-
rity by encrypting the data that is sent over the WLAN. Select Enabled or Disabled. Disabled is the default setting. WEP Encryption- Select the level of encryption desired: 64-bit, or 128-bit Key Type-
Keys 1-4-
Select HEX or ASCII Input up to 4 WEP keys; select the one you wish to use 25 Using the Configuration Utility in AP Client Mode (continued) Home > Wireless > WPA-PSK SSID-
Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSIDs factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Click Site Survey to view the available networks. Channel-
6 is the default channel. All devices on the network must share the same channel. (Note: The wireless adapters will automatically scan and match the wireless setting.) Wireless Mode-
Select Infrastructure or Ad-Hoc mode. Authentication-
Select Open System, Shared Key or WPA-PSK When WPA-PSK is selected fill in the following fields:
Passphrase: Enter the Passphrase here. Confirmed Passphrase: Confirm the Passphrase here. Apply: Click Apply to apply the changes. 26 Using the Configuration Utility in AP Client Mode (continued) Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DWL-G730AP. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address-
Subnet Mask-
The IP address of the LAN interface. The default IP address is:
192.168.0.30 The subnet mask of the LAN interface. The default subnet mask is 255.255.255.0 Gateway-
The IP address of the router. DNS Server-
The IP address of the Domain Name Server. 27 Using the Configuration Utility in AP Client Mode (continued) Advanced > Performance Beacon Interval:
Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346. If you experience a high packet error rate, you may slightly increase your fragmentation threshold within the value range of 256 to 2346. Setting the fragmentation threshold too low may result in poor performance. DTIM Interval: (Delivery Traffic Indication Message) Enter a value between 1 and 255
(default is 3) for the Delivery Traffic Indication Message (DTIM.) A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. TX Rates: Select the transmission rate for the network. The default setting is Auto. Preamble Type: Short Preamble is the default setting. (High traffic networks should use the shorter preamble type.) The preamble defines the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) used in communication between the access point and the wireless network adapters. SSID Broadcast: (Service Set Identifier) Enable or Disable (default) the broadcast of the SSID name across the network. SSID is a name that identifies a wireless network. All devices on a network must use the same SSID to establish communication. Antenna Transmit Power: Select the transmission power of the antenna. Limiting antenna power can be useful for security purposes. 28 Using the Configuration Utility in AP Client Mode (continued) Tools > Admin Administrator Settings-
New Password-
Confirm Password- Enter the password again. Enter the password. 29 Using the Configuration Utility in AP Client Mode (continued) Tools > System The current system settings can be saved as a file onto the local hard drive. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. Save Settings to Local Hard Drive-
Click Save to save the current settings to the local hard drive Load Settings from Local Hard Drive-
Restore to Factory Default Settings-
Click Browse to find the settings, then click Load Click Restore to restore the factory default settings 30
1 | Part 2 | Users Manual | 3.52 MiB | August 09 2004 |
Using the Configuration Utility in AP Client Mode (continued) Tools > Firmware You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the computer. Check the D-Link support site for firmware updates at http://support.dlink.com and download firmware upgrades to your hard drive. After you have downloaded the firmware upgrade to your hard drive, click Browse to browse the local hard drive and locate the firmware to be used for the update. Firmware Upgrade-
Click on the link in this screen to find out if there is updated firmware; if so, download the new firmware to your hard drive. Browse-
After you have downloaded the new firmware, click Browse in this window to locate the firmware update on your hard drive. Click Apply to complete the firmware upgrade. 31 Using the Configuration Utility in AP Client Mode (continued) Status > Device Info This screen displays the current firmware version, and the current wireless and Ethernet settings of the DWL-G730AP. 32 Using the Configuration Utility in AP Client Mode (continued) Status > Stats This screen displays theTraffic Statistics. Here you can view the amount of packets that pass through the DWL-G730AP on both the Ethernet and the wireless networks. The traffic counter will reset if the device is rebooted. 33 Using the Configuration Utility in AP Client Mode (continued) Help The Help menu is displayed here. Click on a topic to learn more about it. 34 Using the Configuration Utility in Router Mode To configure the DWL-G730AP in Router mode, you must be connected to the router via a wireless network adapter. The LAN Port on the unit functions as a WAN port when the DWL-G730AP is operating in Router mode. To run the setup wizard, establish a wireless connection with the DWL-G730AP and follow the steps below. To use the DWL-G730AP as a router, toggle the switch on the back of the unit.
Open the Web browser Type in the IP address of the router
(http://192.168.0.30) Note: if you have changed the default IP address assigned to the DWL-G730AP, make sure to enter the correct IP address.
Type admin in the User Name field Leave the Password blank Click OK Home > Wizard The Home>Wizard screen will appear. Please refer to the Quick Installation Guide for more information regarding the Setup Wizard. 35 Using the Configuration Utility in Router Mode (continued) Home > Wireless SSID-
Service Set Identifier
(SSID) is the name designated for a specific wireless local area network (WLAN). The SSIDs factory default setting is default. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. Channel-
Authentication-
WEP-
6 is the default channel. All devices on the network must share the same channel. Select Open System to communicate the key across the network. Select Shared Key to limit communication only to those devices that share the same WEP settings. Select WPA-PSK to select Wi-Fi Protected Access without a RADIUS server. Wired Equivalent Privacy (WEP) is a wireless security protocol for Wireless Local Area Networks (WLAN). WEP provides security by encrypting the data that is sent over the WLAN. Select Enabled or Disabled. Disabled is the default setting. WEP Encryption-
Select the level of encryption desired: 64-bit, or 128-bit. Key Type-
Keys 1-4-
Select HEX or ASCII. Input up to 4 WEP keys; select the one you wish to use. 36 Using the Configuration Utility in Router Mode (continued) Home > Wireless > WPA-PSK SSID: (Service Set Identifier) default is the default setting. The SSID is a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. If you choose to change the SSID from the default setting, input your new SSID name in this field. Channel: Channel 6 is the default channel. Input a new number if you want to change the default setting. All devices on the network must be set to the same channel to communicate on the network. Authentication:
When WPA-PSK is selected fill in the following fields:
Passphrase: Enter the Passphrase here. Confirmed Passphrase: Confirm the Passphrase here. Apply: Click Apply to apply the changes. 37 Using the Configuration Utility in Router Mode (continued) Home > WAN > Dynamic IP Address Dynamic IP Address is selected here. Other options include:
Static IP Address
(if your ISP provides you with a static IP address), PPPoE (for most DSL users), PPTP (for Europe) and BigPond Cable (for Australia). Dynamic IP Address-
Host Name-
MAC Address-
Clone MAC Address-
Primary/
Secondary DNS Address-
MTU-
Choose Dynamic IP Address to obtain an IP address automatically. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed. The default MAC address is set to the WANs physical interface MAC address on the router. It is not recommended that you change the default MAC address unless required by your ISP. The default MAC address is set to the WANs physical interface MAC address on the router. You can use the Clone MAC Address button to copy the MAC address of the Ethernet Card installed by your ISP and replace the WAN MAC address with the MAC address of the router. It is not recommended that you change the default MAC address unless required by your ISP. Enter a DNS address if you do not wish to use the one provided by your ISP. Maximum Transmission Unit-1500 is the default setting-
Enter an MTU value only if required by your ISP. Otherwise, leave it at the default setting. 38 Using the Configuration Utility in Router Mode (continued) Home > LAN LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DWL-G730AP. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address-
Subnet Mask-
The IP address of the LAN interface. The default IP address is:
192.168.0.30 The subnet mask of the LAN interface. The default subnet mask is 255.255.255.0 Local Domain-
This field is optional. Enter in the local domain name. 39 Using the Configuration Utility in Router Mode (continued) Home > DHCP DHCP stands for Dynamic Host Control Protocol. The DWL-G730AP has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/
private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to Obtain an IP Address Automatically. When you turn your computers on, they will automatically load the proper TCP/
IP settings provided by the DWL-G730AP. The DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool. DHCP Server-
Select Enabled or Disabled. The default setting is Enabled. Starting IP Address-The starting IP address for the DHCP servers IP assignment. Ending IP Address-
Lease Time-
The ending IP address for the DHCP servers IP assignment. The length of time for the IP lease. Enter the Lease time. The default setting is one hour. Static DHCP is used to allow the DHCP server to assign some Static IP addresses via specific MAC addresses. Static DHCP-
Name-
Select Enabled or Disabled. Enter a name here. IP-
MAC Address-
DHCP Client-
Enter the last digits of the IP address here. Enter the MAC address of the computer that will be assigned the Static DHCP IP address. Use this pull-down list to list DHCP clients on your network. To copy the MAC address into the MAC address section above, simply select the client from the pull-down list and click the Clone button. 40 Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server The DWL-G730AP can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DWL-G730AP firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DWL-G730AP are invisible to the outside world. If you wish, you can make some of the LAN computers accessible from the Internet by enabling Virtual Server. Depending on the requested service, the DWL-G730AP redirects the external service request to the appropriate server within the LAN network. The DWL-G730AP is also capable of port-redirection meaning incoming traffic to a particular port may be redirected to a different port on the server computer. Each virtual service that is created will be listed at the bottom of the screen in the Virtual Servers List. There are pre-defined virtual services already in the table. You may use them by enabling them and assigning the server IP to use that particular virtual service. 41 Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server (continued) Virtual Server-
Select Enabled or Disabled. Name-
Private IP-
Enter the name referencing the virtual service. The server computer in the LAN (Local Area Network) that will be providing the virtual services. Protocol Type-
The protocol used for the virtual service. Private Port-
The port number of the service used by the Private IP computer. Public Port-
Schedule-
Example #1:
The port number on the WAN (Wide Area Network) side that will be used to access the virtual service. The schedule of time when the virtual service will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. If it is set to From, select the time frame for the service to be enabled. If the system time is outside of the scheduled time, the service will be disabled. If you have a Web server that you wanted Internet users to access at all times, you would need to enable it. Web
(HTTP) server is on LAN (Local Area Network) computer 192.168.0.25. HTTP uses port 80, TCP. Name: Web Server Private IP: 192.168.0.25 Protocol Type: TCP Private Port: 80 Public Port: 80 Schedule: always 42 Using the Configuration Utility in Router Mode (continued) Advanced > Virtual Server (continued) Click on this icon to edit the virtual service Click on this icon to delete the virtual service Example #2:
If you have an FTP server that you wanted Internet users to access by WAN port 2100 and only during the weekends, you would need to enable it as such. FTP server is on LAN computer 192.168.0.30. FTP uses port 21, TCP. Name: FTP Server Private IP: 192.168.0.30 Protocol Type: TCP Private Port: 21 Public Port: 2100 Schedule: From: 01:00AM to 01:00AM, Sat to Sun All Internet users who want to access this FTP Server must connect to it from port 2100. This is an example of port redirection and can be useful in cases where there are many of the same servers on the LAN network. 43 Using the Configuration Utility in Router Mode (continued) Advanced > Applications Some applications such as Internet gaming, video conferencing, Internet telephony and others, require multiple connections. These applications save difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DWL-G730AP. If you need to run applications that require multiple connections, specify the port normally associated with an application in the Trigger Port field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic. Note! Only one PC can use each Special Application tunnel. Name:
This is the name referencing the special application. Trigger Port:
This is the port used to trigger the application. It can be either a single port or a range of ports. Trigger Type:
This is the protocol used to trigger the special application. Public Port:
This is the port number on the WAN side that will be used to access the application. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. This is the protocol used for the special application. Public Type:
Special Applications List The DWL-G730AP provides some predefined applications in the table on the bottom of the Web page. Select the application you want to use and enable it. 44 Using the Configuration Utility in Router Mode (continued) Advanced > Filters > IP Filters Filters are used to deny or allow LAN (Local Area Network) computers from accessing the Internet. The DWL-G730AP can be setup to deny internal computers by their IP or MAC addresses. The DWL-G730AP can also block users from accessing restricted web sites. IP Filters:
Use IP Filters to deny LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for the specific IP address. IP:
Port:
The IP address of the LAN computer that will be denied access to the Internet. The single port or port range that will be denied access to the Internet. Protocol Type:
Select the protocol type Schedule:
This is the schedule of time when the IP Filter will be enabled. 45 Using the Configuration Utility in Router Mode (continued) Advanced > Filters > URL Blocking URL Blocking:
Select Enable or Disable. Enter the words or word contained in the URL that you wish to block. Click Apply to activate the URL blocking. Delete:
Apply:
Select the URL block that you want to delete. Click Delete. Click Apply to save changes. 46 Using the Configuration Utility in Router Mode (continued) Advanced > Filters > MAC Filters Disable MAC Filters:
Click to Disable MAC Filters. Allow:
Deny:
Name:
Clear:
MAC Address:
Clone:
Apply:
Allow only those devices with the listed MAC addresses access to the network. Deny the devices that are listed from accessing the network. Enter a name for the device. Click Clear to erase the name. Enter the MAC address manually. Select the DHCP Client from the pull-down list and click Clone to enter the MAC address into the list. Click Apply to save the changes. 47 Using the Configuration Utility in Router Mode (continued) Advanced > Filters > Domain Blocking Disable:
Allow:
Deny:
Permitted Domains:
Blocked Domains:
Delete:
Click Disable to disable domain blocking. Click Allow to allow access to all domains except Blocked Domains. Click Deny to deny access to all domains except Permitted Domains. Enter the permitted domains here. Click Apply. Enter the blocked domains here. Click Apply. Select a domain from either the permitted or blocked domain list, and click Delete to delete this domain. 48 Using the Configuration Utility in Router Mode (continued) Advanced > Firewall Firewall Rules is an advanced feature used to deny or allow traffic from passing through the DWL-G730AP. It works in the same way as IP Filters with additional settings. You can create more detailed access rules for the DWL-G730AP. When virtual services are created and enabled, it will also display in Firewall Rules. Firewall Rules contain all network firewall rules pertaining to IP
(Internet Protocol). Note:
The DWL-G730AP MAC Address filtering rules have precedence over the Firewall Rules. Firewall Rules-
Name-
Action-
Source-
Destination-
Enable or disable the Firewall Enter the name Allow or Deny Enter the IP Address range Enter the IP Address range; the Protocol;
and the Port Range Schedule-
Select Always or enter the Time Range. In the Firewall Rules List at the bottom of the screen,rules are prioritized from the top
(highest priority) to the bottom (lowest priority.) 49 Using the Configuration Utility in Router Mode (continued) Advanced > DMZ 30 If you have a client PC that cannot run Internet applications properly from behind the DWL-G730AP, then you can set the client up for unrestricted Internet access. Allowing a computer to be exposed to the Internet, this feature is useful for gaming purposes. Enter the IP address of the internal computer that will be the DMZ host. Using the DMZ
(Demilitarized Zone) feature may expose your local network to a variety of security risks, so only use this option as a last resort. DMZ-
Enable or Disable the DMZ. The DMZ (Demilitarized Zone) allows a single computer to be exposed to the internet. By default the DMZ is disabled. IP Address-
Enter the IP Address of the computer to be in the DMZ 50 Using the Configuration Utility in Router Mode (continued) Advanced > Performance Beacon Interval: Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. Default (100) is recommended. RTS Threshold: This value should remain at its default setting of 2432. If you encounter inconsistent data flow, only minor modifications to the value range between 256 and 2432 are recommended. Fragmentation: This value should remain at its default setting of 2346. If you experience a high packet error rate, you may slightly increase your fragmentation threshold within the value range of 256 to 2346. Setting the fragmentation threshold too low may result in poor performance. DTIM Interval (Beacon Rate): (Delivery Traffic Indication Message) Enter a value between 1 and 255 (default is 3) for the Delivery Traffic Indication Message (DTIM.) A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. TX Rates: Select the transmission rate for the network. The default setting is Auto. Mode Setting: For utmost speed, select G Mode to include only 802.11g devices in your network. Select Mix Mode to include 802.11g and 802.11b devices in your network. Preamble: Short Preamble is the default setting. (High traffic networks should use the shorter preamble type.) The preamble defines the length of the CRC block (Cyclic Redundancy Check is a common technique for detecting data transmission errors) used in communication between the access point and the wireless network adapters. Authentication:
Select Open System to communicate the key across the network. Select Shared Key to limit communication only to those devices that share the same WEP settings. Select WPA-PSK to select Wi-Fi Protected Access without a RADIUS server. SSID Broadcast: (Service Set Identifier) Enable or Disable (default) the broadcast of the SSID name across the network. SSID is a name that identifies a wireless network. All devices on a network must use the same SSID to establish communication. Antenna Transmit Power: Select the transmission power of the antenna. Limiting antenna power can be useful for security purposes. 51 Using the Configuration Utility in Router Mode (continued) Tools > Admin admin is the Administrator login name Enter the password and enter again to confirm Enter the password and enter again to confirm user is the User login name At this page, the DWL-G730AP administrator can change the system password. There are two accounts that can access the routers Web-management interface. They are admin and user. Admin has read/write access while user has read-only access. The user can only view the settings but cannot make any changes. Administrator-
Password-
User-
Password-
Remote Management- Remote management allows the DWL-G730AP to be configured from the Internet by a Web browser. A username and password is still required to access the Web-management interface. In general, only a member of your network can browse the built-in Web pages to perform Administrator tasks. This feature enables you to perform Administrator tasks from the remote (Internet) host. IP Address- The Internet IP address of the computer that has access to the router. If you input an asterisk (*) into this field, then any computer will be able to access the router. Putting an asterisk (*) into this field would present a security risk and is not recommended. Port- The port number used to access the router. Example- http://x.x.x.x:8080 where x.x.x.x is the WAN IP address of the router and 8080 is the port used for the Web-mangement interface. 52 Using the Configuration Utility in Router Mode (continued) Tools > Time Time Zone-
Default NTP Server-
Select the time zone from the pull-down menu. NTP is short for Network Time Protocol. NTP synchronizes computer clock times in a network of computers. This field is optional. Set the Time-
To manually input the time, enter the values in these fields for the year, month, day, hour, minute, and second. Click Set Time. Daylight Saving-
To select daylight saving time manually, select enabled or disabled, and enter a start date and an end date for daylight saving time. 53 Using the Configuration Utility in Router Mode (continued) Tools > System The current system settings can be saved as a file onto the local hard drive. To reload a system settings file, click on Browse to browse the local hard drive and locate the system file to be used. Save Settings to Local Hard Drive-
Load Settings from Local Hard Drive-
Restore to Factory Default Settings-
Click Save to save the current settings to the local hard drive Click Browse to find the settings, then click Load Click Restore to restore the factory default settings 54 Using the Configuration Utility in Router Mode (continued) Tools > Firmware You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the computer. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. After you have downloaded the firmware upgrade to your hard drive, click Browse to browse the local hard drive and locate the firmware to be used for the update. Firmware Upgrade-
Click on the link in this screen to find out if there is updated firmware; if so, download the new firmware to your hard drive. Browse-
After you have downloaded the new firmware, click Browse in this window to locate the firmware update on your hard drive. Click Apply to complete the firmware upgrade. 55 Using the Configuration Utility in Router Mode (continued) Tools > Misc Ping Test-
Restart Device-
Block WAN Ping-
UPNP-
Gaming Mode-
VPN Pass Through-
The ping test is used to send ping packets to test if a computer is on the Internet. Enter the IP address that you wish to ping, and click Ping. Click Reboot to restart the DWL-G730AP. If you choose to block WAN ping, the WAN IP address of the DWL-G730AP will not respond to pings. Blocking the ping may provide some extra security from hackers. Discard Ping from WAN side Click Enabled to block the WAN ping To use the Universal Plug and Play fea-
ture click on Enabled. UPnP provides compatibility with networking equipment, software and peripherals of the over 400 vendors that cooperate in the Plug and Play forum. Gaming mode allows a form of pass-through for certain Internet games. If you are using Xbox, Playstation2 or a PC, make sure you are using the latest firmware and Gaming Mode is enabled. To utilize Gaming Mode, click Enabled. If you are not using a Gaming application, it is recommended that you Disable Gaming Mode. The DWL-G730AP supports VPN (Virtual Private Network) pass-through for both PPTP (Point-to-Point Tunneling Protocol) and IPSec
(IP Security). Once VPN pass-through is enabled, there is no need to open up virtual services. Multiple VPN connections can be made through the DWL-G730AP. This is useful when you have many VPN clients on the LAN network. PPTP- select Enabled or Disabled IPSec- select Enabled or Disabled WAN select to 10/
100Mbps- Select the data rate : 10Mbps, 100Mbps or 10/100Mbps Auto. Dynamic DNS-
Dynamic Domain Name System is a method of keeping a domain name linked to a changing IP Address. This is a useful feature since many computers do not use a static IP address. Enter the IP address and Host Name of the Domain Name Server. Enter your Username and Password. Apply-
Click Apply to save the changes. 56 Using the Configuration Utility in Router Mode (continued) Status > Device Info This page displays the current information for the DWL-G730AP. It will display the LAN, WAN and MAC address information. If your WAN connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your WAN connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection. This window will display the following settings:
LAN WAN Wireless MAC address of the DWL-G730AP IP Address: LAN/Private IP address of the DWL-G730AP Subnet Mask: LAN/Private subnet mask DHCP Server (Enabled or Disabled) MAC address of the DWL-G730AP Client connection (DHCP or PPoE client status) IP address: WAN/Public IP address Subnet Mask: WAN/Public subnet mask Gateway: WAN/Public Gateway IP address Domain Name Server: WAN/Public DNS IP address MAC Address: Displays the MAC address SSID: Displays the current SSID Channel: Displays the current channel WEP: indicates whether WEP is enabled or disabled 57 Using the Configuration Utility in Router Mode (continued) Status > Log View Log displays the activities occurring on the DWL-G730AP. Click on Log Settings for advance features. The DWL-G730AP keeps a running log of events and activities. If the device is rebooted, the logs are automatically cleared. You may save the log files under Log Settings. View Log-
First Page - The first page of the log Last Page - The last page of the log Previous - Moves back one log page Next - Moves forward one log page Clear - Clears the logs completely Log Settings - Brings up the page to configure the log 58 Using the Configuration Utility in Router Mode (continued) Status > Stats This screen displays theTraffic Statistics. Here you can view the amount of packets that pass through the DWL-G730AP on both the WAN and the LAN ports. The traffic counter will reset if the device is rebooted. Click Refresh to view the latest statistics. Click Reset to reset. The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless client. Click on Help at any time, for more information. Status > Wireless 59 Networking Basics Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, Me or 98SE. Go to Start>Control Panel>Network Connections Select Set up a home or small office network When this screen appears, click Next. 60 Networking Basics (continued) Please follow all the instructions in this window:
Click Next. In the following window, select the best description of your computer. If your computer connects to the internet through a gateway/router, select the second option as shown. Click Next. 61 Networking Basics (continued) Enter a Computer description and a Computer name (optional.) Click Next. Enter a Workgroup name. All computers on your network should have the same Workgroup name. Click Next. 62 Networking Basics (continued) Please wait while the Network Setup Wizard applies the changes. When the changes are complete, click Next. Please wait while the Network Setup Wizard configures the computer. This may take a few minutes. 63 Networking Basics (continued) In the window below, select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. You will run this disk on each of the computers on your network. Click Next. Insert a disk into the Floppy Disk Drive, in this case drive A. 64 Networking Basics (continued) Please wait while the Network Setup Wizard copies the files. Please read the information under Heres how in the screen below. After you com-
plete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue click Next. 65 Networking Basics (continued) Please read the information on this screen, then click Finish to complete the Network Setup Wizard. The new settings will take effect when you restart the computer. Click Yes to restart the computer. You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use. 66 Networking Basics (continued) Naming your Computer To name your computer, please follow these directions:In Windows XP:
Click Start (in the lower left corner of the screen). Right-click on My Computer. Select Properties and click.
Select the Computer Name Tab in the System Properties window.
You may enter a Computer Description if you wish; this field is optional.
To rename the computer and join a domain, Click Change. 67 Networking Basics (continued) Naming your Computer
In this window, enter the Computer name.
Select Workgroup and enter the name of the Workgroup. All computers on your network must have the same Workgroup name.
Click OK. Checking the IP Address in Windows XP The wireless adapter-equipped computers in your network must be in the same IP Address range (see Getting Started in this manual for a definition of IP Address Range.) To check on the IP Address of the adapter, please do the following:
Right-click on the Local Area Connection icon in the task bar.
Click on Status. 68 Networking Basics (continued) Checking the IP Address in Windows XP This window will appear.
Click the Support tab.
Click Close. Assigning a Static IP Address in Windows XP/2000 Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses. If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these instructions:
Go to Start.
Double-click on Control Panel. 69 Networking Basics (continued) Assigning a Static IP Address in Windows XP/2000
Double-click on Network Connections.
Right-click on Local Area Connections.
Double-click on Properties. 70 Networking Basics (continued) Assigning a Static IP Address in Windows XP/2000
Click on Internet Protocol
(TCP/IP).
Click Properties. Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window (shown below)
In the window below, select Use the following IP address. Input your IP address and subnet mask. (The IP addresses on your network must be within the same range. For example, if one computer has an IP address of 192.168.0.2, the other computers should have IP addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.) IP Address:
e.g., 192.168.0.2 Subnet Mask:
255.255.255.0 Default Gateway:
Enter the LAN IP address of the wireless router. (D-Link wireless routers have a LAN IP address of 192.168.0.1)
Select Use the following DNS server address. Enter the LAN IP address of the wireless router. (D-Link wireless routers have a LAN IP address of 192.168.0.1)
Click OK. You have completed the assignment of a static IP address. (You do not need to assign a static IP address if you have a DHCP-capable router.) 71 Networking Basics (continued) Checking the Wireless Connection by Pinging in Windows XP/2000
Go to Start > Run >
type cmd. A window similar to this one will appear. Type ping xxx.xxx.xxx.xxx, where xxx is the IP address of the wireless router or access point. A good wireless connection will show four replies from the wireless router or access point, as shown. Checking the Wireless Connection by Pinging in Windows Me /98SE
Go to Start > Run
> type command. A window similar to this will appear. Type ping xxx.xxx.xxx.xxx where xxx is the IP address of the wireless router or access point. A good wireless connection will show four replies from the wireless router or access point, as shown. 72 Technical Specifications Standards
IEEE 802.11b
IEEE 802.11g
IEEE 802.3
IEEE 802.3u Device Management
Web-Based Internet Explorer v6 or later; Netscape Navigator v7 or later; or other Java-enabled browsers. Data Rate For 802.11g:
54, 48, 36, 24, 18, 12, 9 and 6Mbps For 802.11b:
11, 5.5, 2, and1Mbps Security
64-, 128-bit WEP
WPA Wi-Fi Protected Access
MAC Address Filtering
SSID Broadcast Disable Wireless Frequency Range
2.412GHz to 2.462GHz Wireless Operating Range*
802.11g (Full Power with internal antenna) Outdoors:
164ft (50m) @ 54Mbps
492ft (150m) @ 11Mbps
656ft (200m) @ 6Mbps Power
External Power Supply: DC 5V/1.2A
* Environmental factors may adversely affect wireless range 73 Technical Specifications (continued) Radio and Modulation Type For 802.11g:
OFDM:
BPSK @ 6 and 9Mbps
QPSK @ 12 and 18Mbps
16QAM @ 24 and 36Mbps
64QAM @ 48 and 54Mbps DSSS:
DBPSK @ 1Mbps
DQPSK @ 2Mbps
CCK @ 5.5 and 11Mbps For 802.11b:
DSSS:
DBPSK @ 1Mbps
DQPSK @ 2Mbps
CCK @ 5.5 and 11Mbps Wireless Transmit Power Typical RF Output Power at each Data Rate For 802.11g:
31mW (15dBm) @ 54Mbps
40mW (16dBm) @ 48Mbps
40mW (16dBm) @ 36, 24, 18, 12, 9, and 6Mbps For 802.11b:
50mW (17dBm) @ 11, 5.5, 2, and 1Mbps Receiver Sensitivity For 802.11g:
6Mbps: -87dBm
9Mbps: -85dBm
12Mbps: -82dBm
18Mbps: -81dBm
24Mbps: -80dBm
36Mbps: -79dBm
48Mbps: -71dBm
54Mbps: -69dBm For 802.11b:
1Mbps: -90dBm
2Mbps: -90dBm
5.5Mbps: -86dBm
11Mbps: -85dBm 74 Technical Specifications (continued) LEDs
Power
LAN
WLAN Temperature
Operating: 32F to 131F (0C to 55C)
Storing: -4F to 149F (-20C to 65C) Humidity
Operating: 10%~90% (non-condensing)
Storing: 5%~95% (non-condensing) Certifications
FCC
CE Dimensions
L = 3.15 inches (80mm)
W = 2.36 inches (60mm)
H = 0.67 inches (17mm) Weight
0.11 lbs (50g) Warranty
1 Year 75 Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone. Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465 24 hours a day, seven days a week. D-Link Technical Support over the Internet:
http://support.dlink.com email:support@dlink.com Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265 Monday to Friday 7:30am to 12:00am EST D-Link Technical Support over the Internet:
http://support.dlink.ca email:support@dlink.ca 76 Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (D-Link) provides this Limited warranty for its product only to the person or entity that originally purchased the product from:
D-Link or its authorized reseller or distributor and Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO. Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will be free from material defects in workmanship and materials from the date of original retail purchase of the product, for the period set forth below applicable to the product type (Warranty Period), except as otherwise stated herein. 1-Year Limited Warranty for the Product(s) is defined as follows:
Hardware (excluding power supplies and fans) One (1) Year Power Supplies and Fans One (1) Year Spare parts and spare kits Ninety (90) days D-Links sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund at D-Links sole discretion. Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new or have an identical make, model or part. D-Link may in its sole discretion replace the defective Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement Hardware will be warranted for the remainder of the original Warranty Period from the date of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund. Limited Software Warranty: D-Link warrants that the software portion of the product (Software) will substantially conform to D-Links then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (Warranty Period), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation. D-Link further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers the Software will be free of physical defects. D-Links sole obligation shall be to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Links functional specifications for the Software or to refund at D-Links sole discretion. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Software will be warranted for the remainder of the original Warranty Period from the date or original retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the non-
conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates. Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of D-Links products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold As-Is without any warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary. Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same. 77 The original product owner must obtain a Return Material Authorization (RMA) number from the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the warranty service is provided. After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the Product and will not ship back any accessories. The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery
(COD) is allowed. Products sent COD will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited shipping is available if shipping charges are prepaid by the customer and upon request. Return Merchandise Ship-To Address USA: 17595 Mt. Herrmann, Fountain Valley, CA 92708 Canada: 2180 Winston Park Drive, Oakville, ON, L6H 5W1 (Visit http://www.dlink.ca for detailed warranty information within Canada) D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Links reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming. What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Links judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance;
Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;
Any hardware, software, firmware or other products or services provided by anyone other than D-
Link; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty. Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED AS-IS WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT. Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-
LINKS PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY. 78 Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective manufacturers or owners. Copyright Statement: No part of this publication or documentation accompanying this Product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior notice. Copyright 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment; such modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For detailed warranty outside the United States, please contact corresponding local D-Link office. Register your D-Link product online at http://support.dlink.com/register/
(08/10/04) 79
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2004-09-08 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2004-09-08
|
||||
1 | Applicant's complete, legal business name |
D-Link Corporation
|
||||
1 | FCC Registration Number (FRN) |
0007371172
|
||||
1 | Physical Address |
17595 Mt. Herrmann
|
||||
1 |
Fountain Valley, California 92708
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@americanTCB.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
KA2
|
||||
1 | Equipment Product Code |
DWLG730APA1
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
B**** A****
|
||||
1 | Title |
General Counsel
|
||||
1 | Telephone Number |
714-8********
|
||||
1 | Fax Number |
866-7********
|
||||
1 |
b******@dlink.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation
|
||||
1 | Name |
E****** W********
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd.
|
||||
1 |
Taoyuan, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
+886 ******** Extension:
|
||||
1 | Fax Number |
+886 ********
|
||||
1 |
e******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 802.11g Wireless Pocket Router / Access Point | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R****** C****
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0630000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC