| submitted | available | document details (if available) | source link |
|---|---|---|---|
| April 10 2017 | Adobe PDF Library 15.0 |
| various | User Manual | Users Manual | 4.50 MiB | / April 10 2017 |
Version 1.01 | 09/15/2017 User Manual AC1200 Wi-Fi Router DIR-815 D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Preface Manual Revisions Revision 1.0 Date Description 3 January, 2017 Initial release for revision D1 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies. Internet Explorer, Windows and the Windows logo are trademarks of the Microsoft group of companies. Copyright 2017 by D-Link Corporation, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation, Inc. The purpose of this product is to create a constant network connection for your devices. As such, it does not have a standby mode or use a power management mode. If you wish to power down this product, please simply unplug it from the power outlet. This device is an Energy Related Product (ErP) with High Network Availability (HiNA), and automatically switches to a power-saving Network Standby mode within 1 minute of no packets being transmitted. It can also be turned off through a power switch to save energy when it is not needed. Power Usage Network Standby: 5.19 watts Switched Off: 0.26 watts D-Link DIR-815 User Manual i Table of Contents Package Contents ..............................................................1 System Requirements ................................................................. 2 Introduction ................................................................................... 3 Features ............................................................................................ 4 Hardware Overview ..................................................................... 5 LEDs ........................................................................................... 5 Connections ........................................................................... 6 Installation .........................................................................7 Before You Begin ........................................................................... 7 Wireless Installation Considerations ...................................... 8 Hardware Setup ............................................................................ 9 Completing Setup ......................................................................12 Setup Wizard ................................................................................13 Configuration ...................................................................21 Web UI Table of Contents ........................................................22 Setup ...............................................................................................23 Internet ...................................................................................24 Internet Connection Setup Wizard ..........................25 Manual Internet Connection Setup ........................33 Wireless Settings .................................................................43 Wireless Connection Setup Wizard..........................44 Add Wireless Device with WPS ..................................47 Manual Wireless Connection Setup ........................50 Wireless Security Mode ...............................................52 Network Settings ................................................................54 Storage ...................................................................................57 D-Link DIR-815 User Manual IPv6 ..........................................................................................58 IPv6 Internet Connection Setup Wizard ................59 IPv6 Local Connectivity Settings ..............................63 Manual IPv6 Internet Connection Setup ...............64 Advanced ......................................................................................80 Virtual Server ........................................................................81 Port Forwarding ..................................................................82 Application Rules ................................................................83 QOS Engine ...........................................................................84 Network Filter.......................................................................86 Inbound Filter ......................................................................87 Access Control .....................................................................88 Add Policy .........................................................................89 Website Filter ........................................................................92 Firewall Settings ..................................................................93 Routing ...................................................................................95 Advanced Wireless .............................................................96 Wi-Fi Protected Setup .......................................................97 Advanced Network ............................................................98 Guest Zone ............................................................................99 IPv6 Firewall ....................................................................... 100 IPv6 Routing ...................................................................... 102 Tools ............................................................................................. 103 Admin .................................................................................. 104 Time ...................................................................................... 105 Syslog ................................................................................... 106 Email Settings ................................................................... 107 ii Table of Contents WPA/WPA2 ......................................................................... 146 Troubleshooting ............................................................148 Wireless Basics ...............................................................152 What is Wireless? ...................................................................... 153 Tips ................................................................................................ 155 Wireless Modes ......................................................................... 156 Networking Basics .........................................................157 Check your IP address ............................................................ 157 Statically Assign an IP address ............................................ 158 Wireless Security ......................................................... 159 What is WPA? ................................................................ 159 Technical Specifications ................................................160 Regulatory Information ................................................161 System ................................................................................. 109 Firmware ............................................................................. 110 Dynamic DNS .................................................................... 111 System Check .................................................................... 112 Schedules ........................................................................... 113 Status ........................................................................................... 114 Device Info ......................................................................... 115 Logs ...................................................................................... 117 Statistics .............................................................................. 118 Internet Sessions .............................................................. 119 Wireless ............................................................................... 120 Routing ................................................................................ 121 IPV6 ....................................................................................... 122 IPv6 Routing ...................................................................... 123 Support ....................................................................................... 124 Connect and Share a USB Storage Device ...................125 Connecting from a Windows-Based PC ........................... 126 Connecting from a Mac ......................................................... 131 Connect a Wireless Client to Your Router .....................134 WPS Button ................................................................................ 134 Windows 10 ............................................................................. 135 Windows 8 ................................................................................ 137 WPA/WPA2 ......................................................................... 137 Windows 7 ................................................................................ 139 WPA/WPA2 ......................................................................... 139 WPS ....................................................................................... 141 Windows Vista ......................................................................... 145 D-Link DIR-815 User Manual iii Table of Contents Package Contents DIR-815 AC1200 Wi-Fi Router Power Adapter Ethernet Cable Wi-Fi Configuration Card Quick Install Guide If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DIR-815 will cause damage and void the warranty for this product. D-Link DIR-815 User Manual 1 Section 1 - Product Overview System Requirements Network Requirements An Ethernet-based cable or DSL modem IEEE 802.11ac, 802.11n, 802.11a, 802.11g, or 802.11b wireless clients 10/100 Ethernet Computer with the following:
Windows, Macintosh, or Linux-based operating system An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements:
Internet Explorer 9 or higher Firefox 20 or higher Safari 5.1 or higher Chrome 25 or higher Windows Users: Make sure you have the latest version of Java installed. Visit www.java.com to download the latest version. D-Link DIR-815 User Manual 2 Section 1 - Product Overview Introduction The D-Link DIR-815 AC1200 Wi-Fi Router shares your Internet connection over a blazing-fast wireless connection of up to 1200 Mbps (up to 866 Mbps over 5 GHz Wireless AC and up to 300 Mbps over 2.4 GHz Wireless N)1, using advanced AC beamforming technology to significantly outperform 802.11n and other 802.11ac devices. Equipped with one Fast Ethernet WAN/Internet port and four Fast Ethernet LAN ports, providing speeds up to 10 times faster than standard 10/100 ports and creating the best networking experience to date. Featuring four antennas, the AC1200 Wi-Fi Router offers better data rates, fewer dead-spots, more coverage, and higher reliability. Operating exclusively in the 5 GHz band, the DIR-815s 802.11ac wireless connections avoid the crowded 2.4 GHz band, giving you faster speeds while still maintaining backwards compatibility with older 802.11n/g/b devices. A stronger Wi-Fi signal means you can install more wireless surveillance cameras, baby monitors, sensors, and alarms in the places where you need them. The DIR-815 supports the latest security features to help prevent unauthorized access. Support for WPA and WPA2 standards ensure that you will be able to use the best possible encryption regardless of your client devices. This router is also equipped with a dual-active firewall (SPI and NAT) to prevent potential attacks over the Internet. The DIR-815 is full of features to improve your home network. The built-in USB 2.0 port lets you easily share a USB storage drive with all the devices on your local network. The rich parental controls allow you to easily control when the Internet should be available in your home and what content is allowed. With all this and more, the DIR-815 AC1200 Wi-Fi Router will serve your network well for years to come. 1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n and 802.11ac specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range. D-Link DIR-815 User Manual 3 Section 1 - Product Overview Features Excellent Wireless Networking - The DIR-815 provides wireless speeds of up to a combined 1200 Mbps (866 Mbps 802.11ac 5 GHz, plus 300 Mbps 802.11n 2.4 GHz)1. This capability rivals wired connections, allowing users to participate in real-time activities online, such as HD video communication, online gaming, and use mobile devices from anywhere in your home while still offering full 802.11n/g/b backward compatibility. Fast Wired LAN and WAN Networking - With four 10/100 Fast Ethernet LAN ports, and a 10/100 Fast Ethernet WAN port, the DIR-815 has a high amount of bandwidth to take full advantage of the highest speed broadband connections available. IPv6 Support - The DIR-815 fully supports IPv6 and includes support for a variety of IPv6 connection types including: SLAAC/DHCPv6, 6to4, 6rd, Static IPv6, IPv6 PPPoE, IPv6 in IPv4 tunneling, and local connectivity. Advanced Firewall Features - The web-based user interface displays a number of advanced network management features. Easily apply content filtering based on MAC address, URL, and/or domain name. Schedule these filters to be active on certain days or for a duration of hours or minutes. Secure Multiple/Concurrent Sessions - The DIR-815 can pass through VPN sessions. It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-815 can securely access corporate networks. User-friendly Setup Wizard - Through its easy-to-use web-based, the DIR-815 lets you quickly configure and secure your router to your specific settings in minutes. 1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n and 802.11ac specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range. D-Link DIR-815 User Manual 4 Section 1 - Product Overview Hardware Overview LEDs 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Power Internet The Power LED indicates that the device is powered on with a proper connection to the power supply. The Internet LED indicates that an Internet link is established. It blinks during data transmission. WPS The WPS LED blinks during the WPS pairing process. 2.4 GHz Wireless The Wireless LED indicates that this wireless band is working. It blinks during wireless data transmission. 5 GHz Wireless The Wireless LED indicates that this wireless band is working. It blinks during wireless data transmission. LAN Port (1-4) The LAN Port LEDs indicate an Ethernet device is connected. They blink during data transmission. USB The USB LED indicates that a USB device is connected to the USB 2.0 port. D-Link DIR-815 User Manual 5 Section 1 - Product Overview Hardware Overview Connections 1 WPS Button Press to start the WPS process and automatically create a secure connection to a WPS client. 2 Reset Button (on bottom) Insert a paperclip in the hole, wait for 10 seconds, and release to reset the router to default settings. 3 4 5 6 7 8 Wi-Fi Button Press to enable or disable the wireless networks. LAN Ports (1-4) Connect Ethernet devices such as computers, switches, storage (NAS) devices and game consoles. Internet Port Using an Ethernet cable, connect your broadband modem to this port. USB Port Connect a USB flash drive to share on your network. Power Connector Connector for the supplied power adapter. Power Button Press the power button to power the device on and off. D-Link DIR-815 User Manual 6 Section 1 - Product Overview Installation Before You Begin Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, attic, or garage. Configure the router with the computer that was last connected directly to your Internet connection. Verify that it is connected to the Internet before connecting additional devices. If your ISP provided you with a modem/router combo, you will need to set it to bridge mode so the router can work properly. Please contact your Internet Service Provider (ISP) or refer to the user manual for your modem/router device. You can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet). If connecting to a DSL modem, make sure to have your DSL service information provided by your Internet Service Provider handy. This information is likely to include your DSL account's username and password. Your ISP may also supply you with additional WAN configuration settings which might be necessary to establish a connection. If you are connecting a considerable amount of networking equipment, it may be a good idea to take the time to label each cable or take a picture of your existing setup before making any changes. If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoET, BroadJump, or EnterNet 300 from your computer or you will not be able to connect to the Internet. D-Link DIR-815 User Manual 7 Section 2 - Installation Wireless Installation Considerations This D-Link wireless device lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum - each wall or ceiling can reduce your adapters range from 1 to 30 meters (3 to 90 feet). Position your devices so that the number of walls or ceilings is minimized. 2. Be aware of the direct line between network devices. A wall that is 0.5 meters (1.5 feet) thick, at a 45-degree angle appears to be almost 1 meter (3 feet) thick. At a 2-degree angle it looks over 14 meters (42 feet) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. 3. Building materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal. 4. Keep your product away at least 1 to 2 meters (3 to 6 feet) from electrical devices or appliances that generate RF noise. 5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not in use. D-Link DIR-815 User Manual 8 Section 2 - Installation 1. The DIR-815 is designed to give you the fastest, most stable network connection possible. In order to maximize performance, fully extend the antennas to provide optimal wireless coverage. Keep the router in an open area for better wireless coverage. Hardware Setup DIR-815 2. Position your DIR-815 near your Internet-connected modem. Place it in an open area for better wireless coverage. DIR-815 Modem 3. Turn off and unplug the power and Ethernet cable to your cable or DSL broadband modem. This is required. In some cases, you may need to turn it off for up to five minutes. DIR-815 Modem D-Link DIR-815 User Manual 9 Section 2 - Installation Hardware Setup (continued) 4. Use the included Ethernet cable to connect your modem to the yellow port labeled INTERNET on the router. DIR-815 Modem 5. Turn on or plug your modem back in and wait approximately one minute before proceeding onward. DIR-815 Modem 6. Connect the supplied power adapter to the router and a power outlet, press the power button, and verify that the power LED is lit. Allow 1 minute for the router to boot up. DIR-815 Modem D-Link DIR-815 User Manual 10 Section 2 - Installation Hardware Setup (continued) 7. If you are configuring the DIR-815 wirelessly from a PC, connect to a Wi-Fi network printed on the included Wi-Fi configuration card. You can also find the Wi-Fi network names and passwords printed on the label attached to the bottom of your router. Wi-Fi Configuration Card DIR-815 Modem If you are configuring the DIR-815 from a PC with a wired Ethernet connection, plug one end of an Ethernet cable into the port labeled 1 on the back of the router, and the other end into the Ethernet port on your computer. DIR-815 Modem 8. If you are connecting to a broadband service that uses a dynamic connection (not PPPoE), you may be online already. Try opening a web browser and connecting to a website. If the website does not load, proceed to Completing Setup on page 12. D-Link DIR-815 User Manual 11 Section 2 - Installation Completing Setup There are several different ways you can configure your router to connect to the Internet and connect to your clients:
D-Link Setup Wizard - This wizard will launch when you log into the router for the first time, refer to Setup Wizard on page 13. Manual Setup - Log into the router and manually configure your router, refer to Configuration on page 21. D-Link DIR-815 User Manual 12 Section 2 - Installation If this is your first time installing the router, open your web browser and enter http://dlinkrouter.local./ in the address bar. Alternatively, enter the IP address of the router
(default: http://192.168.0.1). The first time you log in, the setup wizard will run. Setup Wizard WELCOME TO THE D-LINK SETUP WIZARD WELCOME TO THE D-LINK SETUP WIZARD This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. The wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Step 1: Configure your Internet Connection Step 2: Configure your Wi-Fi Security Step 3: Set your Password Step 4: Select your Time Zone Step 5: Confirm Wi-Fi Settings Cancel Next Click Next to continue. D-Link DIR-815 User Manual 13 Section 2 - Installation Step 1 - Configure Your Internet Connection STEP 1: CONFIGURE YOUR INTERNET CONNECTION STEP 1: CONFIGURE YOUR INTERNET CONNECTION The router is detecting your Internet connection type, please wait... Please wait while your router attempts to detect your Internet connection type. You may need to enter information such as your ISP account username and password. Cancel Prev Next Next to continue. STEP 1: CONFIGURE YOUR INTERNET CONNECTION Select the connection type your ISP uses. If you select DHCP Connection (Dynamic IP Address), proceed to Step 2 - Configure Your Wi-Fi Security on page 19. For Username / Password Connection (PPPoE) setup help refer to page 15. For Username / Password Connection (PPTP) setup help refer to page 15. For Username / Password Connection (L2TP) setup help refer to page 16. For Static IP Address Connection setup help refer to page 18. Select your connection type and click Next to continue. STEP 1: CONFIGURE YOUR INTERNET CONNECTION If your Internet Service Provider was not listed or you dont know who it is, please select the Internet connection type below:
DHCP Connection (Dynamic IP Address) Choose this if your Internet connection automatically provides you with an IP Address. Most Cable Modems use this type of connection. Username / Password Connection (PPPoE) Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type of connection. Username / Password Connection (PPTP) PPTP client. Username / Password Connection (L2TP) L2TP client. Static IP Address Connection Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually configured. Cancel Prev Next D-Link DIR-815 User Manual 14 Section 2 - Installation Username / Password Connection (PPPoE) If you chose Username / Password Connection (PPPoE) as your Internet Connection, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE) Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19. SET USERNAME AND PASSWORD CONNECTION (PPPOE) To set up this connection you will need to have a Username and Password from your Internet Service Provider. If you do not have this information, please contact your ISP. User Name :
Password :
Cancel Prev Next Username / Password Connection (PPTP) If you choose Username / Password Connection (PPTP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPTP) SET USERNAME AND PASSWORD CONNECTION (PPTP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need PPTP IP address. If you do not have this information, please contact your ISP. Address Mode: Select either Dynamic IP or Static IP Address Mode : Dynamic IP Static IP If you choose Static IP as the Address Mode, enter your IP address:
PPTP IP Address: Enter the PPTP IP Address provided by your ISP. PPTP Subnet Mask:
PPTP Gateway IP Address:
Enter the PPTP Subnet Mask provided by your ISP. DNS SETTINGS Enter the PPTP Gateway IP Address provided by your ISP. If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
PPTP Server IP Address:
Enter the PPTP Server IP address provided by your ISP. PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address (may be same as gateway):
User Name :
Password :
Verify Password :
Primary DNS Address :
Secondary DNS Address :
Cancel Prev Next D-Link DIR-815 User Manual 15 Section 2 - Installation PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address (may be same as gateway):
User Name :
Password :
Verify Password :
Primary DNS Address :
Secondary DNS Address :
Username / Password Connection (PPTP) (continued) User Name: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. SET USERNAME AND PASSWORD CONNECTION (PPTP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need PPTP IP address. If you do not have this information, please contact your ISP. Address Mode : Dynamic IP Static IP DNS SETTINGS Enter the primary DNS server IP addresses. DNS SETTINGS Enter the secondary DNS server IP addresses. Cancel Prev Next Primary DNS Server:
Secondary DNS Server:
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19. Username / Password Connection (L2TP) If you choose Username / Password Connection (L2TP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (L2TP) SET USERNAME AND PASSWORD CONNECTION (L2TP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need L2TP IP address. If you do not have this information, please contact your ISP. Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
L2TP IP Address: Enter the L2TP IP Address provided by your ISP. L2TP Subnet Mask:
L2TP Gateway IP Address:
Enter the L2TP Subnet Mask provided by your ISP. DNS SETTINGS Enter the L2TP Gateway IP Address provided by your ISP. Address Mode : Dynamic IP Static IP L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
(may be same as gateway) User Name :
Password :
Verify Password :
Primary DNS Address :
Secondary DNS Address :
(optional) Cancel Prev Next D-Link DIR-815 User Manual 16 Section 2 - Installation Username / Password Connection (L2TP) (continued) If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
SET USERNAME AND PASSWORD CONNECTION (L2TP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need L2TP IP address. If you do not have this information, please contact your ISP. Address Mode : Dynamic IP Static IP L2TP Server IP Address:
Enter the L2TP Server IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. DNS SETTINGS Verify Password: Enter the password provided by your ISP one more time. L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
(may be same as gateway) User Name :
Password :
Verify Password :
Primary DNS Address :
Secondary DNS Address :
(optional) Cancel Prev Next DNS SETTINGS Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. Primary DNS Server:
Secondary DNS Server:
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19. D-Link DIR-815 User Manual 17 Section 2 - Installation If you choose Static IP Address Connection as your Internet Connection, enter your IP address, configure the following settings:
Static IP Address Connection SET STATIC IP ADDRESS CONNECTION IP Address: Enter the IP address provided by your ISP. Subnet Mask: Enter the subnet mask. Default Gateway: Enter the default gateway. DNS SETTINGS Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. Primary DNS Server:
Secondary DNS Server:
Click Next and proceed to Step 2 - Configure Your Wi-Fi Security on page 19. SET STATIC IP ADDRESS CONNECTION To set up this connection you will need to have a complete list of IP information provided by your Internet Service Provider. If you have a Static IP connection and do not have this information, please contact your ISP. IP Address :
Subnet Mask :
Default Gateway :
DNS SETTINGS Primary DNS Address :
Secondary DNS Address :
(optional) Cancel Prev Next D-Link DIR-815 User Manual 18 Section 2 - Installation Step 2 - Configure Your Wi-Fi Security STEP 2: CONFIGURE YOUR WI-FI SECURITY Wi-Fi Network Name(SSID):
Enter a name for the 2.4 GHz wireless network. Wi-Fi Password: Enter a wireless password according to the onscreen guidelines. Wi-Fi Network Name(SSID):
Enter a name for the 5 GHz wireless network. STEP 2: CONFIGURE YOUR WI-FI SECURITY Give your Wi-Fi network a name and a password. (2.4GHz Band) Wi-Fi Network Name(SSID) :
Your_2.4GHz_Network
(Using up to 32 characters) Wi-Fi Password :
A_Str0ng_P@ssWord!
(Between 8 and 63 characters) Give your Wi-Fi network a name and a password. (5GHz Band) Wi-Fi Network Name(SSID) :
Your_5GHz_Network
(Using up to 32 characters) Wi-Fi Password :
A_Str0ng_P@ssWord!
(Between 8 and 63 characters) Wi-Fi Password: Enter a wireless password according to the onscreen guidelines. Cancel Prev Next Click Next to continue. Step 3: Set Your Password STEP 3: SET YOUR PASSWORD STEP 3: SET YOUR PASSWORD By default, your new D-Link Router does not have a password configured for administrator access to the Web-based configuration pages. To secure your new networking device, please set and verify a password below:
Enter a new administration password. This is the password you will use to log in to the router. Click Next to continue. Password :
Verify Password :
Cancel Prev Next Step 4: Select Your Time Zone STEP 4: SELECT YOUR TIME ZONE STEP 4: SELECT YOUR TIME ZONE Select the appropriate time zone for your location. This information is required to configure the time-based options for the router. Select your time zone. Click Next to continue. Time Zone :
(GMT+08:00) Taipei Cancel Prev Next D-Link DIR-815 User Manual 19 Section 2 - Installation Step 5: Confirm Wi-Fi Settings Step 5 is a summary of your wireless settings. Click Next to finish the wizard. STEP 5: CONFIRM WI-FI SETTINGS STEP 5: CONFIRM WI-FI SETTINGS Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a piece of paper, so you can configure the correct settings on your Wi-Fi devices. Wi-Fi Network Name(SSID) 2.4GHz : Your_2.4GHz_Network Wi-Fi Password A_Str0ng_P@ssWord!
Wi-Fi Network Name(SSID) 5GHz : Your_5GHz_Network Wi-Fi Password A_Str0ng_P@ssWord!
Congratulations, your device has been successfully configured. The router will reboot and display the login page. LOGIN Login to the router :
Cancel Prev Next User Name :
Admin Password :
Login D-Link DIR-815 User Manual 20 Section 2 - Installation Configuration This section will show you how to configure or change the default settings your D-Link DIR-815 using the web-based configuration utility. To access the configuration utility, open a web browser such as Internet Explorer and enter http://dlinkrouter.local./ or you may also connect by typing the IP address of the router
(by default this is http://192.168.0.1) in the address bar. LOGIN Login to the router :
User Name :
Admin Password :
Login Enter your password. If you previously followed the setup wizard, please use the admin password you entered during the wizard. Otherwise, leave the password blank. Click Login to proceed. Note: If you cannot remember your password and cannot log in, press the reset button on the back of the device for longer than 10 seconds to restore the router to its default settings. If you are having trouble logging in or experiencing trouble with the configuration utility, try clearing your browser cache or try using your web browsers private browsing mode. DIR-815 INTERNET WIRELESS SETTINGS NETWORK SETTINGS STORAGE IPV6 SETUP ADVANCED TOOLS STATUS SUPPORT INTERNET CONNECTION If you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection Setup. INTERNET CONNECTION SETUP WIZARD If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the Internet, click on the button below. Internet Connection Setup Wizard Note:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the package. MANUAL INTERNET CONNECTION OPTION If you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below. D-Link DIR-815 User Manual Manual Internet Connection Setup 21 Section 3 - Configuration Web UI Table of Contents The web-based interface is divided into 5 horizontal tabs, each with a vertical menu bar running along the left side. You may click on these section titles to quickly navigate to a section of this document. DIR-815 SETUP ADVANCED TOOLS STATUS SUPPORT INTERNET VIRTUAL SERVER WIRELESS SETTINGS PORT FORWARDING NETWORK SETTINGS APPLICATION RULES ADMIN TIME SYSLOG DEVICE INFO LOGS STATISTICS STORAGE IPV6 QOS ENGINE EMAIL SETTINGS INTERNET SESSIONS NETWORK FILTER INBOUND FILTER SYSTEM FIRMWARE ACCESS CONTROL DYNAMIC DNS WIRELESS ROUTING IPV6 WEBSITE FILTER SYSTEM CHECK IPV6 ROUTING FIREWALL SETTINGS SCHEDULES MENU SETUP ADVANCED TOOLS STATUS ROUTING ADVANCED WIRELESS WI-FI PROTECTED SETUP ADVANCED NETWORK GUEST ZONE IPV6 FIREWALL IPV6 ROUTING To return to this Web UI Table of Contents page, simply click the D-Link logo on the top right of each page. DIR-815 INTERNET SETUP INTERNET CONNECTION D-Link DIR-815 User Manual 22 Section 3 - Configuration The Setup tab provides access to configure the basic configuration settings of your DIR-815. Setup SETUP ADVANCED TOOLS STATUS SUPPORT DIR-815 INTERNET WIRELESS SETTINGS NETWORK SETTINGS STORAGE IPV6 To return to the Web UI Table of Contents page, simply click the D-Link logo on the top right of each page. DIR-815 INTERNET SETUP INTERNET CONNECTION D-Link DIR-815 User Manual 23 Section 3 - ConfigurationINTERNET CONNECTIONIf you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection Setup.INTERNET CONNECTION SETUP WIZARDIf you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the Internet, click on the button below.Internet Connection Setup WizardNote:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the package.MANUAL INTERNET CONNECTION OPTIONIf you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below.Manual Internet Connection Setup Internet Click Internet on the navigation menu to configure your Internet connection. Using the Internet Connection Setup Wizard is recommended. To manually configure your Internet connection, select Manual Internet Connection Setup. INTERNET CONNECTION SETUP WIZARD Click Internet Connection Setup Wizard to configure your Internet Connection. Refer to Internet Connection Setup Wizard on page 25. MANUAL INTERNET CONNECTION OPTION DIR-815 INTERNET INTERNET CONNECTION SETUP INTERNET CONNECTION If you are configuring the device for the first time, we recommend that you click on the Internet Connection Setup Wizard, and follow the instructions on the screen. If you wish to modify or configure the device settings manually, click the Manual Internet Connection Setup. INTERNET CONNECTION SETUP WIZARD If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the Internet, click on the button below. Internet Connection Setup Wizard Click Manual Internet Connection Setup to manually add or configure your Internet connection. Refer to Manual Wireless Connection Setup on page 50. Note:Before launching the wizard, please make sure you have followed all steps outlined in the Quick Installation Guide included in the package. MANUAL INTERNET CONNECTION OPTION If you would like to configure the Internet settings of your new D-Link Router manually, then click on the button below. Manual Internet Connection Setup D-Link DIR-815 User Manual 24 Section 3 - Configuration Internet Connection Setup Wizard This Internet Connection Setup Wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. WELCOME TO THE D-LINK INTERNET CONNECTION SETUP WIZARD This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Step 1: Set your Password Step 2: Select your Time Zone Step 3: Configure your Internet Connection Step 4: Save Settings and Connect Prev Next Cancel Connect STEP 1: SET YOUR PASSWORD STEP 1: SET YOUR PASSWORD By default, your new D-Link Router does not have a password configured for administrator access to the Web-based configuration pages. To secure your new networking device, please set and verify a password below:
Enter a new administration password. This is the password you will use to log in to the router. Click Next to continue. Password :
Verify Password :
Prev Next Cancel Connect STEP 2: SELECT YOUR TIME ZONE STEP 2: SELECT YOUR TIME ZONE Select the appropriate time zone for your location. This information is required to configure the time-based options for the router. Select your time zone. Click Next to continue. STEP 3: CONFIGURE YOUR INTERNET CONNECTION Select the connection type your ISP uses and click Next to continue. For DHCP setup help refer to page 26. For PPPoE setup help refer to page 27. For PPTP setup help refer to page 28. For L2TP setup help refer to page 30. For Static IP Address Connection setup help refer to page 32. Time Zone :
(GMT+08:00) Taipei Prev Next Cancel Connect STEP 3: CONFIGURE YOUR INTERNET CONNECTION Please select the Internet connection type below:
DHCP Connection (Dynamic IP Address) Choose this if your Internet connection automatically provides you with an IP Address. Most Cable Modems use this type of connection. Username / Password Connection (PPPoE) Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type of connection. Username / Password Connection (PPTP) Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type of connection. Username / Password Connection (L2TP) Choose this option if your Internet connection requires a username and password to get online. Most DSL modems use this type of connection. Static IP Address Connection Choose this option if your Internet Setup Provider provided you with IP Address information that has to be manually configured. Prev Next Cancel Connect D-Link DIR-815 User Manual 25 Section 3 - Configuration Internet Connection Setup Wizard (continued) DHCP If you choose DHCP Connection (Dynamic IP Address) as your Internet Connection, enter your IP address, configure the following settings:
DHCP CONNECTION (DYNAMIC IP ADDRESS) MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. DHCP CONNECTION (DYNAMIC IP ADDRESS) To set up this connection, please make sure that you are connected to the D-Link Router with the PC that was originally connected to your broadband connection. If you are, then click the Clone MAC button to copy your computers MAC Address to the D-Link Router. MAC Address :
(optional) Clone Your PCs MAC Address Host Name :
dlinkrouter Host Name: Enter the host name of the router. Note: You may also need to provide a Host Name.If you do not have or know this information, please contact your ISP. DNS SETTINGS DNS SETTINGS Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. Primary DNS Server:
Secondary DNS Server :
Click Next to continue. Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings. Prev Next Cancel Connect D-Link DIR-815 User Manual 26 Section 3 - Configuration Internet Connection Setup Wizard (continued) PPPoE If you choose Username / Password Connection (PPPoE) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE) Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. SET USERNAME AND PASSWORD CONNECTION (PPPOE) To set up this connection you will need to have a Username and Password from your Internet Service Provider. If you do not have this information, please contact your ISP. User Name :
Password :
Prev Next Cancel Connect Click Next to continue. Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings. v Prev Next Cancel Connect D-Link DIR-815 User Manual 27 Section 3 - Configuration Internet Connection Setup Wizard (continued) PPTP If you choose Username / Password Connection (PPTP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPTP) SET USERNAME AND PASSWORD CONNECTION (PPTP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need PPTP IP address. If you do not have this information, please contact your ISP. Address Mode : Dynamic IP Static IP PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address :
(may be same as gateway) User Name :
Password :
Verify Password :
DNS SETTINGS Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
PPTP IP Address: Enter the PPTP IP Address provided by your ISP. PPTP Subnet Mask:
PPTP Gateway IP Address:
Enter the PPTP Subnet mask provided by your ISP. Enter the PPTP Gateway IP Address provided by your ISP. If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
PPTP Server IP Address:
Enter the PPTP Server IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. DNS SETTINGS Enter the primary DNS server IP addresses. Primary DNS Server:
D-Link DIR-815 User Manual 28 Section 3 - Configuration Internet Connection Setup Wizard (continued) PPTP (continued) Secondary DNS Server :
Enter the secondary DNS server IP addresses. DNS SETTINGS Click Next to continue. Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings. Prev Next Cancel Connect D-Link DIR-815 User Manual 29 Section 3 - Configuration Internet Connection Setup Wizard (continued) L2TP If you choose Username / Password Connection (L2TP) as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (L2TP) SET USERNAME AND PASSWORD CONNECTION (L2TP) To set up this connection you will need to have a Username and Password from your Internet Service Provider. You also need L2TP IP address. If you do not have this information, please contact your ISP. Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
L2TP IP Address: Enter the PPTP IP Address provided by your ISP. L2TP Subnet Mask:
L2TP Gateway IP ddress:
Enter the PPTP Subnet mask provided by your ISP. DNS SETTINGS Enter the PPTP Gateway IP Address provided by your ISP. If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
L2TP Server IP Address:
Enter the PPTP Server IP address provided by your ISP. Address Mode : Dynamic IP Static IP L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
(may be same as gateway) User Name :
Password :
Verify Password :
Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. DNS SETTINGS Enter the primary DNS server IP addresses. Primary DNS Server:
D-Link DIR-815 User Manual 30 Section 3 - Configuration Internet Connection Setup Wizard (continued) L2TP (continued) Secondary DNS Server :
Enter the secondary DNS server IP addresses. DNS SETTINGS Click Next to continue. Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings. Prev Next Cancel Connect D-Link DIR-815 User Manual 31 Section 3 - Configuration Internet Connection Setup Wizard (continued) Static IP Address Connection If you choose Static IP Address Connection as your Internet Connection, enter your IP address, configure the following settings:
SET STATIC IP ADDRESS CONNECTION IP Address: Enter the IP address provided by your ISP. Subnet Mask: Enter the subnet mask. Default Gateway: Enter the default gateway. DNS SETTINGS Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. Primary DNS Server:
Secondary DNS Server :
Click Next to continue. SET STATIC IP ADDRESS CONNECTION To set up this connection you will need to have a complete list of IP information provided by your Internet Service Provider. If you have a Static IP connection and do not have this information, please contact your ISP. IP Address :
Subnet Mask :
Default Gateway :
DNS SETTINGS Primary DNS Address :
Secondary DNS Address :
(optional) Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The Internet Connection Setup Wizard has completed. Click the Connect button to save your settings. Prev Next Cancel Connect D-Link DIR-815 User Manual 32 Section 3 - Configuration Manual Internet Connection Setup Click Manual Internet Setup on from the Internet menu to configure your Internet connection manually. This section is only recommended for advanced users. It is recommended to use the Setup Wizard to set up your Internet connection. INTERNET CONNECTION TYPE My Internet Connection is:
Select the Internet Connection protocol from the dropdown menu your ISP uses. The options are Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. For Static IP setup help refer to page 34. Select the connection type your ISP uses. For Dynamic IP (DHCP) setup help refer to page 35. For PPPoE (Username / Password) setup help refer to page 36. For PPTP (Username / Password) setup help refer to page 38. For L2TP (Username / Password) setup help refer to page 40. For DS-Lite setup help refer to page 42. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
Static IP Dynamic IP (DHCP) PPPoE (Username / Password) PPTP (Username / Password) L2TP (Username / Password) DS-Lite D-Link DIR-815 User Manual 33 Section 3 - Configuration Static IP If you choose Static IP, please configure the following fields:
STATIC IP ADDRESS INTERNET CONNECTION TYPE :
IP Address: Enter the IP address provided by your ISP. Subnet Mask: Enter the subnet mask. Default Gateway: Enter the default gateway. Primary DNS Server:
Secondary DNS Server :
Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. MTU Size: Enter the MTU size. MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
Static IP STATIC IP ADDRESS INTERNET CONNECTION TYPE :
Enter the static address information provided by your Internet Service Provider (ISP). IP Address :
Subnet Mask :
Default Gateway :
Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1500 MAC Address :
Clone Your PCs MAC Address When you have finished configuring your Internet connection, click the Save Settings button. Save Settings Dont Save Settings D-Link DIR-815 User Manual 34 Section 3 - Configuration Dynamic IP (DHCP) If you choose Dynamic IP (DHCP), please configure the following fields:
STATIC IP ADDRESS INTERNET CONNECTION TYPE :
Host Name: Enter the host name of the router. Use Unicasting: Check this box if you are having difficulty obtaining a DHCP address from your ISP. Primary DNS Server:
Secondary DNS Server :
Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. MTU Size: Enter the MTU size. MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is : Dynamic IP (DHCP) DYNAMIC IP (DHCP) INTERNET CONNECTION TYPE :
Use this Internet connection type if your Internet Service Provider (ISP) didnt provide you with IP Address information and/or a username and password. Host Name :
dlinkrouter Use Unicasting : (compatibility for some DHCP Clients) Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1500 MAC Address :
Clone Your PCs MAC Address When you have finished configuring your Internet connection, click the Save Settings button. Save Settings Dont Save Settings D-Link DIR-815 User Manual 35 Section 3 - Configuration PPPoE (Username / Password) If you choose PPPoE, please configure the following fields:
PPPOE INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
IP Address: Enter the IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
PPPoE (Username / Password) PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP Verify Password: Enter the password provided by your ISP one more time. Service Name: Enter the ISP service name (optional). Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create a schedule by clicking New Schedule. Refer to Schedules on page 113 for more information. If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
Maximum Idle Time:
Set the length of time to wait before disconnecting if there is no Internet activity. (Manual Only) IP Address :
User Name :
Password :
Verify Password :
Service Name :
(optional) Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) DNS Mode : Receive DNS from ISP Enter DNS Manually Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings DNS Mode: Select either Receive DNS from ISP or Enter DNS Manually. If you choose Enter DNS Manually as the DNS Mode, enter your DNS information:
Primary DNS Server:
Enter the primary DNS server IP addresses. D-Link DIR-815 User Manual 36 Section 3 - Configuration PPPoE (Username / Password) (Continued) Secondary DNS Server :
Enter the secondary DNS server IP addresses. MTU Size: Enter the MTU size. MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. When you have finished configuring your Internet connection, click the Save Settings button. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
PPPoE (Username / Password) PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP IP Address :
User Name :
Password :
Verify Password :
Service Name :
(optional) Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) DNS Mode : Receive DNS from ISP Enter DNS Manually Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings D-Link DIR-815 User Manual 37 Section 3 - Configuration PPTP (Username / Password) If you choose PPTP, please configure the following fields:
PPTP INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
PPTP IP Address: Enter the PPTP IP Address provided by your ISP. PPTP Subnet Mask:
PPTP Gateway IP Address:
Enter the PPTP Subnet mask provided by your ISP. Enter the PPTP Gateway IP Address provided by your ISP. If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
PPTP Server IP Address:
Enter the PPTP Server IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create a schedule by clicking New Schedule. Refer to Schedules on page 113 for more information. If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
PPTP (Username / Password) PPTP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings D-Link DIR-815 User Manual 38 Section 3 - Configuration PPTP (Username / Password) (Continued) Maximum Idle Time:
Set the length of time to wait before disconnecting if there is no Internet activity. (Manual Only) Primary DNS Server:
Secondary DNS Server :
Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. MTU Size: Enter the MTU size. MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. When you have finished configuring your Internet connection, click the Save Settings button. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
PPTP (Username / Password) PPTP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP PPTP IP Address :
PPTP Subnet Mask :
PPTP Gateway IP Address :
PPTP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings D-Link DIR-815 User Manual 39 Section 3 - Configuration L2TP (Username / Password) If you choose L2TP, please configure the following fields:
L2TP INTERNET CONNECTION TYPE :
Address Mode: Select either Dynamic IP or Static IP If you choose Static IP as the Address Mode, enter your IP address:
L2TP IP Address: Enter the PPTP IP Address provided by your ISP. L2TP Subnet Mask:
L2TP Gateway IP ddress:
Enter the PPTP Subnet mask provided by your ISP. Enter the PPTP Gateway IP Address provided by your ISP. If you choose Dynamic IP or Static IP as the Address Mode, enter your PPTP Server IP address:
L2TP Server IP Address:
Enter the PPTP Server IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. Reconnect Mode: Select either AlwaysOn, On Demand, or Manual. You may create a schedule by clicking New Schedule. Refer to Schedules on page 113 for more information. If you choose Manual as the Reconnect Mode, enter the Maximum Idle Time:
DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
L2TP (Username / Password) L2TP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings D-Link DIR-815 User Manual 40 Section 3 - Configuration L2TP (Username / Password) (continued) Maximum Idle Time:
Set the length of time to wait before disconnecting if there is no Internet activity. (Manual Only) Primary DNS Server:
Secondary DNS Server :
Enter the primary DNS server IP addresses. Enter the secondary DNS server IP addresses. MTU Size: Enter the MTU size. MAC Address:
If your Internet connection is tied to a specific PC or hardware, enter it manually or click Clone Your PCs MAC Address. When you have finished configuring your Internet connection, click the Save Settings button. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is :
L2TP (Username / Password) L2TP INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). Address Mode : Dynamic IP Static IP L2TP IP Address :
L2TP Subnet Mask :
L2TP Gateway IP Address :
L2TP Server IP Address :
Username :
Password :
Verify Password :
Reconnect Mode :
AlwaysOn New Schedule On Demand Manual Maximum Idle Time :
(minutes) Primary DNS Server :
Secondary DNS Server :
(optional) MTU :
1492 MAC Address :
Clone Your PCs MAC Address Save Settings Dont Save Settings D-Link DIR-815 User Manual 41 Section 3 - Configuration DS-Lite If you choose DS-Lite, please configure the following fields:
DS-Lite Mode: Select either DS-Lite DHCPv6 Option or Manual Configuration. If you choose Manual Configuration, configure the AFTR IPv6 Address field:
AFTR Name or Address:
Enter the AFTR Name or Address. If you choose DS-Lite DHCPv6 Option or Manual Configuration, configure the B4 IPv6 Address field:
B4 IPv6 Address: Enter the B4 IPv6 Address. (optional) Your WAN IPv6 address is listed here. WAN IPv6 Address:
IPv6 WAN Default Gateway:
Your WAN IPv6 default gateway address is listed here. Save Settings Dont Save Settings When you have finished configuring your Internet connection, click the Save Settings button. DIR-815 INTERNET WAN SETUP WAN Use this section to configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and DS-Lite. If you are unsure of your connection method, please contact your Internet Service Provider. Note : If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Save Settings Dont Save Settings INTERNET CONNECTION TYPE Choose the mode to be used by the router to connect to the Internet. My Internet Connection is : DS-Lite AFTR ADDRESS INTERNET CONNECTION TYPE :
Enter the AFTR address information provided by your Internet Service Provider (ISP). DS-Lite Configuration : DS-Lite DHCPv6 Option Manual Configuration AFTR IPv6 Address :
B4 IPv4 Address : 192.0.0.
(optional) WAN IPv6 Address :
IPv6 WAN Default Gateway :
D-Link DIR-815 User Manual 42 Section 3 - Configuration Wireless Settings Click Wireless Settings on the navigation menu to configure your Wireless Settings. You may run the Wireless Connection Setup Wizard, Add a Device with WPS, or run the Manual Wireless Connection Setup. WIRELESS NETWORK SETUP WIZARD Click the Wireless Connection Setup Wizard button to easily configure your wireless settings. Refer to page Wireless Connection Setup Wizard on page 44 for more information. ADD WIRELESS DEVICE WITH WPS (WI-FI PROTECTED SETUP) WIZARD Click the Add Wireless Device with WPS button (Wi-Fi Protected Setup) to add a device using WPS Wizard. MANUAL WIRELESS CONNECTION SETUP Click the Manual Wireless Connection Setup button to manually configure your wireless LAN settings. DIR-815 SETUP WIRELESS SETTINGS WIRELESS SETTINGS WIRELESS SETTINGS The following Web-based wizards are designed to assist you in your wireless network setup and wireless device connection. Before launching these wizards, please make sure you have followed all steps outlined in the Quick Installation Guide included in the package. WIRELESS NETWORK SETUP WIZARD This wizard is designed to assist you in your wireless network setup. It will guide you through step-by-step instructions on how to set up your wireless network and how to make it secure. Note:Some changes made using this Setup Wizard may require you to change some settings on your wireless client adapters so they can still connect to the D-Link Router. Wireless Connection Setup Wizard ADD WIRELESS DEVICE WITH WPS (WI-FI PROTECTED SETUP) WIZARD This wizard is designed to assist you in connecting your wireless device to your wireless router. It will guide you through step-by-step instructions on how to get your wireless device connected. Click the button below to begin. Add Wireless Device with WPS MANUAL WIRELESS CONNECTION SETUP If your wireless network is already set up with Wi-Fi Protected Setup, manual configuration of the wireless network will destroy the existing wireless network. If you would like to configure the wireless settings of your new D-Link Systems Router manually, then click on the Manual Wireless Network Setup button below. Manual Wireless Connection Setup D-Link DIR-815 User Manual 43 Section 3 - Configuration Wireless Connection Setup Wizard This section describes the Wireless Connection Setup Wizard. STEP 1: WELCOME TO THE D-LINK WIRELESS SECURITY SETUP WIZARD STEP 1: WELCOME TO THE D-LINK WIRELESS SECURITY SETUP WIZARD Give your network a name, using up to 32 characters. Network Name
(SSID) 2.4GHz:
Network Name
(SSID) 5Ghz:
Enter a name for the 2.4 GHz wireless network. Network Name (SSID) 2.4GHz :
Your_2.4GHz_Network Network Name (SSID) 5Ghz :
Your_5GHz_Network Enter a name for the 5 GHz wireless network. Automatically assign a network key (Recommended) To prevent outsiders from accessing your network, the router will automatically assign a security key (also called WEP or WPA) to your network. Manually assign a network key Use this options if you prefer to create our own key. Note: All D-Link wireless adapters currently support WPA. Prev Next Cancel Save Automatically assign a network:
Choose this option to have the router automatically create a secure wireless security key. Manually assign a network key:
Choose this option to create your own wireless security key. Click Next to continue. SETUP COMPLETE!
SETUP COMPLETE!
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a piece of paper, so you can configure the correct settings on your wireless client adapters. If you choose Automatically assign a network, there is no further configuration. A summary of your wireless configuration settings is displayed. Click Save to finish. Wireless Band : 2.4GHz Band Wireless Network Name (SSID) : Your_2.4GHz_Network Security Mode : Auto (WPA or WPA2) - Personal Cipher Type: TKIP and AES Pre-Shared Key : d80a73f50c Wireless Band : 5GHz Band Wireless Network Name (SSID) : Your_5GHz_Network Security Mode : Auto (WPA or WPA2) - Personal Cipher Type: TKIP and AES Pre-Shared Key : d80a73f50c Prev Next Cancel Save D-Link DIR-815 User Manual 44 Section 3 - Configuration Wireless Connection Setup Wizard (continued) If you choose Manually assign a network key, there is no further configuration. A summary of your wireless configuration settings is displayed. STEP 2: SET YOUR WIRELESS SECURITY PASSWORD If you checked Use the same Wireless Security Password on both 2.4GHz and 5GHz band, enter the Wireless Security Password. Wireless Security Password:
Enter a wireless password according to the onscreen guidelines. If you unchecked Use the same Wireless Security Password on both 2.4GHz and 5GHz band, enter a 2.4GhzWireless Security Password and 5GhzWireless Security Password:
2.4GhzWireless Security Password:
5GhzWireless Security Password:
Enter a wireless password according to the onscreen guidelines. Enter a wireless password according to the onscreen guidelines. Click Next to continue. STEP 2: SET YOUR WIRELESS SECURITY PASSWORD You have selected your security level - you will need to set a wireless security password. The WPA (Wi-Fi Protected Access) key must meet one of following guidelines:
- Between 8 and 63 characters (A longer WPA key is more secure than a short one )
- Exactly 64 characters using 0-9 and A-F Use the same Wireless Security Password on both 2.4GHz and 5GHz band Wireless Security Password :
A_Str0ng_P@ssWord!
Note: You will need to enter the same password as keys in this step into your wireless clients in order to enable proper wireless communication. Prev Next Cancel Save STEP 2: SET YOUR WIRELESS SECURITY PASSWORD You have selected your security level - you will need to set a wireless security password. The WPA (Wi-Fi Protected Access) key must meet one of following guidelines:
- Between 8 and 63 characters (A longer WPA key is more secure than a short one )
- Exactly 64 characters using 0-9 and A-F Use the same Wireless Security Password on both 2.4GHz and 5GHz band 2.4GhzWireless Security Password :
A_Str0ng_P@ssWord!
5GhzWireless Security Password :
A_Str0ng_P@ssWord!
Note: You will need to enter the same password as keys in this step into your wireless clients in order to enable proper wireless communication. Prev Next Cancel Save D-Link DIR-815 User Manual 45 Section 3 - Configuration Wireless Connection Setup Wizard (continued) A summary of your wireless configuration settings is displayed. Click Save to finish. SETUP COMPLETE!
SETUP COMPLETE!
Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a piece of paper, so you can configure the correct settings on your wireless client adapters. Click Save to finish. Wireless Band : 2.4GHz Band Wireless Network Name (SSID) : Your_2.4GHz_Network Security Mode : Auto (WPA or WPA2) - Personal Cipher Type: TKIP and AES Pre-Shared Key : A_Str0ng_P@ssWord!
Wireless Band : 5GHz Band Wireless Network Name (SSID) : Your_5GHz_Network Security Mode : Auto (WPA or WPA2) - Personal Cipher Type: TKIP and AES Pre-Shared Key : A_Str0ng_P@ssWord!
Prev Next Cancel Save D-Link DIR-815 User Manual 46 Section 3 - Configuration This section describes the Add Wireless Device with WPS wizard. Add Wireless Device with WPS STEP 1: SELECT CONFIGURATION METHOD NETWORK Auto: Choose this option to automatically add a device to your network using this virtual WPS button. STEP 1: SELECT CONFIGURATION METHOD FOR YOUR WIRELESS NETWORK Please select one of following configuration methods and click next to continue. Auto Select this option if your wireless device supports WPS (Wi-Fi Protected Setup) Manual Select this option will display the current wireless settings for you to configure the wireless device manually Prev Next Cancel Connect Manual: Choose this option to see the currently configured wireless networking settings to enter on your wireless client. Choose your configuration type and refer to the following pages. D-Link DIR-815 User Manual 47 Section 3 - Configuration Add Wireless Device with WPS - Auto If you choose Auto and click Next, choose the WPS configuration type:
STEP 2: CONNECT YOUR WIRELESS DEVICE Select the WPS method to use to connect your wireless device, either PIN or PBC. Using WPS-PIN is not recommended due to security vulnerabilities. PIN: Choose this option and enter the currently configured WPS PIN, refer to Wi-Fi Protected Setup on page 97 for information on setting the WPS Pin. PBC: Choose this option to begin the WPS PBC (Push Button Control) pairing process. Click Continue to continue. STEP 2: CONNECT YOUR WIRELESS DEVICE There are two ways to add wireless device to your wireless network:
-PIN (Personal Identification Number)
-PBC (Push Button Configuration) PIN :
please enter the PIN from your wireless device and click the below Connect Button within 120 seconds please press the push button on your wireless device and click the below Connect Button within 120 seconds PBC :
Prev Next Cancel Connect STEP 2: CONNECT YOUR WIRELESS DEVICE STEP 2: CONNECT YOUR WIRELESS DEVICE Please press down the Push Button (physical or virtual) on the wireless device you are adding to your wireless network. Press the WPS button or enter the WPS PIN on the client device which you wish to add to your DIR-815s network. The WPS process is only active for 120 seconds. Remain time in second: 120 Adding wireless device: Started Prev Next Cancel Save If your device is successfully added, this screen is displayed. Click Wireless Status to be directed to the Wireless Status page. Refer to Wireless on page 120 for more information. STEP 2: CONNECT YOUR WIRELESS DEVICE Adding wireless device: Succeeded. To add another device click on the Cancel button below or click on the Wireless Status button to check wireless status. Prev Next Cancel Wireless Status If your device could not be found, this screen is displayed. You may click Cancel and retry running the wizard again. STEP 2: CONNECT YOUR WIRELESS DEVICE Adding wireless device: Session Time-Out. Prev Next Cancel Save D-Link DIR-815 User Manual 48 Section 3 - Configuration Add Wireless Device with WPS - Manual If you choose Manual and click Next the currently configured wireless networking settings to enter on your wireless client are displayed. STEP 1: SELECT CONFIGURATION METHOD FOR YOUR WIRELESS NETWORK Please select one of following configuration methods and click next to continue. Auto Select this option if your wireless device supports WPS (Wi-Fi Protected Setup) Manual Select this option will display the current wireless settings for you to configure the wireless device manually Click Wireless Status to be directed to the Wireless Status page. Refer to Wireless on page 120 for more information. SETUP COMPLETE!
Prev Next Cancel Connect Below is a detailed summary of your wireless security settings. Please print this page out, or write the information on a piece of paper, so you can configure the correct settings on your wireless client adapters. 2.4 Ghz Frequency SSID: Your_2.4GHz_Network Security Mode: WPA2-PSK Cipher Type: AES
-PIN (Personal Identification Number) Pre-shared Key:
adc058dce7893caf98ca91 5 Ghz Frequency SSID: Your_5GHz_Network Security Mode: None Prev Next Cancel Wireless Status D-Link DIR-815 User Manual 49 Section 3 - Configuration Manual Wireless Connection Setup Click Manual Wireless Connection Setup from the Wireless Settings menu to configure your wireless LAN settings. From this page you can configure the wireless security and network parameters for both the 2.4 GHz and 5 GHz network. When you have finished configuring your wireless network, click Save Settings. WIRELESS NETWORK SETTINGS Wireless Band: 2.4 GHz or 5 GHz Enable Wireless: Enable or disable this wireless network. From the drop down menu you may apply a schedule to enable or disable this wireless network. Click New Schedule to create a new schedule. Refer to Schedules on page 113 for more information. Wireless Network Name:
802.11 Mode
(2.4 GHz):
Create a name for your wireless network. Select the desired wireless networking standards to use. The available options for the 2.4 GHz wireless network are 802.11b only, 802.11g only, 802.11n only, Mixed 802.11g and 802.11b, or the default Mixed 802.11n, 802.11g and 802.11b. DIR-815 SETUP WIRELESS SETTINGS WIRELESS NETWORK WIRELESS NETWORK Use this section to configure the wireless settings for your D-Link router. Please note that changes made in this section may also need to be duplicated on your wireless client. To protect your privacy you can configure wireless security features. Securing your wireless network is important as it is used to protect the integrity of the information being transmitted. The router is capable of 4 types of wireless security; WEP, WPA only, WPA2 only, and WPA/WPA2 (auto-detect). Save Settings Dont Save Settings WIRELESS NETWORK SETTINGS Wireless Band : 2.4GHz Band Enable Wireless : Always New Schedule Wireless Network Name :
Your_2.4GHz_Network 802.11 Mode:
802.11b only 802.11g only 802.11n only Mixed 802.11g and 802.11b Mixed 802.11n and 802.11g Mixed 802.11n, 802.11g and 802.11b Enable Auto Channel Scan :
04 Wireless Channel :
Transmission Rate :
Best (automatic) (Mbit/s) Channel Width :
20 MHz 20/40 MHz(Auto) Visibility Status : Visible Invisible 802.11 Mode
(5 GHz):
Select the desired wireless networking standards to use. The available options for the 2.4 GHz wireless network are 802.11a only, 802.11n only, Mixed 802.11a and 802.11n, Mixed 802.11ac and 802.11n, or the default Mixed 802.11ac, 802.11n and 802.11a. WIRELESS SECURITY MODE Security Mode :
None WEP WPA-Personal WPA-Enterprise Enable Auto Channel Scan:
Check this box to have the router automatically determine the best wireless channel to use. Wireless Channel: If Auto Scan is disabled, use the dropdown menu to select the wireless channel to use. Transmission Rate: Select the desired wireless transmission rate. D-Link DIR-815 User Manual 50 Section 3 - Configuration Manual Wireless Connection Setup (continued) Channel Width
(2.4 GHz):
Select Auto 20/40 if you are using both 802.11n and non-802.11n devices, or select 20 MHz if you are not using any 802.11n devices. Channel Width
(5 GHz):
Select Auto 20/40/80 if you are using 802.11ac, 802.11n, and 802.11a devices. Auto 20/40 select if you are using 802.11n and 802.11a devices. 20 MHz if you are only using 802.11a devices. Higher channel width allows for higher speeds. Visibility Status: The default setting is Visible. Select Invisible if you do not want to broadcast the SSID of your wireless network. Note: Making a network invisible is not a form of security alone. WIRELESS NETWORK SETTINGS Wireless Band : 5GHz Band Enable Wireless : Always New Schedule Wireless Network Name :
Your_5GHz_Network 802.11 Mode:
802.11a only 802.11n only Mixed 802.11a and 802.11n Mixed 802.11ac and 802.11n Mixed 802.11ac, 802.11n and 802.11a Enable Auto Channel Scan :
153 Wireless Channel :
Transmission Rate :
Best (automatic) (Mbit/s) Channel Width :
20 MHz 20/40 MHz(Auto) 20/40/80 MHz(Auto) Visibility Status : Visible Invisible WIRELESS SECURITY MODE WIRELESS SECURITY MODE Security Mode :
Refer to Wireless Security Mode on page 52 for more information on configuring your wireless networks security. None WEP WPA-Personal WPA-Enterprise D-Link DIR-815 User Manual 51 Section 3 - Configuration Wireless Security Mode The following pages describe each type of security option. When you have finished configuring your wireless network, click Save Settings. WIRELESS SECURITY MODE Security Option: Select a wireless security encryption option. The options are None, WEP, WPA-Personal, and WPA-Enterprise. Using WPA is recommended. WIRELESS SECURITY MODE Security Mode :
None WEP WPA-Personal WPA-Enterprise None WIRELESS SECURITY MODE WIRELESS SECURITY MODE Security Mode :
None Security Option: None. Disabling encryption and leaving your wireless network open is not recommended. Any wireless client will be able to access your network, be able to use your Internet connection, and leaves you open to security threats. WEP WIRELESS SECURITY MODE WIRELESS SECURITY MODE Security Mode : WEP Security Option: WEP. Using WEP encryption is not recommended, as it only offers a trivial amount of protection for your wireless data. WEP encryption is only available for use with 802.11b, 802.11g, and 802.11a. WEP Key Length: Select the Encryption cipher key bit strength. The available options are 64 bit (10 hex digits) or 128 bit (26 hex digits). WEP WEP WEP Key Length :
64 bit (10 hex digits)
(length applies to all keys) Authentication :
Both WEP Key 1 :
Authentication: Select either Both or Shared Key. WEP Key 1: Enter a wireless key to use on your wireless network. D-Link DIR-815 User Manual 52 Section 3 - Configuration WPA-Personal / WPA-Enterprise WIRELESS SECURITY MODE Security Option: Select either WPA-Personal or WPA-Enterprise. If you are running a dedicated RADIUS authentication server, choose WPA-Enterprise. WIRELESS SECURITY MODE Security Mode : WPA-Personal WPA-Enterprise WPA WPA Mode: Select either Auto(WPA or WPA2) or WPA2 Only. WPA2 Only is the recommended wireless security type. Select Auto (WPA or WPA2) only if your wireless clients do not support WPA2. Cipher Type: Select either TKIP and AES, TKIP, or AES. Using AES is the recommended since TKIP is no longer considered secure. WPA WPA Mode : WPA2 Only Cipher Type :
AES Group Key Update Interval :
3600
(seconds) Group Key Update Interval:
Enter the group key update interval. If you selected WPA-Personal, enter the Pre-Shared Key:
Pre-Shared Key: Enter a wireless key to use on your wireless network. PRE-SHARED KEY PRE-SHARED KEY Pre-Shared Key :
If you selected WPA-Enterprise, enter your EAP 802.1X Radius server information:
EAP (802.1X) Enter a wireless key to use on your wireless network. EAP (802.1X) RADIUS server IP Address :
RADIUS server Port:
RADIUS server Shared Secret:
RADIUS server IP Address:
RADIUS server Port: Enter your RADIUS servers port number. RADIUS server Shared Secret:
Enter your RADIUS servers shared secret. D-Link DIR-815 User Manual 53 Section 3 - Configuration Network Settings Click Network Settings on the navigation menu to configure your local network settings. When you are satisfied with your configuration, click Save Settings. ROUTER SETTINGS Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Save Settings, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Mask:
Enter the subnet mask of the router. The default subnet mask is 255.255.255.0. Host Name: The default address to access the routers configuration is http://dlinkrouter.local./ Here, you can replace dlinkrouter with a name of your choice. Local Domain Name:
Enter the domain name (optional). Enable DNS Relay: Disable to transfer the DNS server information from your ISP to your computers. If enabled, your computers will use the router for a DNS server. Enable DHCP Server:
DHCP IP Address Range:
DHCP SERVER SETTINGS Enable or disable the DHCP server. Enter the starting and ending IP addresses for the DHCP servers IP assignment. Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. DIR-815 SETUP NETWORK SETTINGS NETWORK SETTINGS NETWORK SETTINGS Use this section to configure the internal network settings of your router and also to configure the built-in DHCP server to assign IP addresses to computers on your network.The IP address that is configured here is the IP address that you use to access the Web-
based management interface.If you change the IP address in this section, you may need to adjust your PC's network settings to access the network again. Please note that this section is optional and you do not need to change any of the settings here to get your network up and running. Save Settings Dont Save Settings ROUTER SETTINGS Use this section to configure the internal network settings of your router.The IP address that is configured here is the IP address that you use to access the Web-based management interface.If you change the IP address here, you may need to adjust your PCs network settings to access the network again. Router IP Address:
192.168.0.1 Default Subnet Mask :
255.255.255.0 Host Name :
dlinkrouter Local Domain Name :
Enable DNS Relay :
(optional) DHCP SERVER SETTINGS Use this section to configure the built-in DHCP server to assign IP address to the computers on your network. Enable DHCP Server :
100 DHCP IP Address Range :
to 200
(addresses within the LAN subnet) DHCP Lease Time :
Always broadcast : (compatibility for some DHCP Clients)
(minutes) 10080 ADD DHCP RESERVATION Enable :
Computer Name :
<<
Computer Name IP Address :
MAC Address :
Clone Your PCs MAC Address Add / Update Clear DHCP RESERVATIONS LIST Enable Host Name IP Address NUMBER OF DYNAMIC DHCP CLIENTS Host Name IP Address MAC Address Expired Time Save Settings Dont Save Settings D-Link DIR-815 User Manual 54 Section 3 - Configuration Network Settings (continued) DHCP Lease Time: The maximum length of time for the IP address lease. Enter the Lease time in minutes. DHCP SERVER SETTINGS Use this section to configure the built-in DHCP server to assign IP address to the computers on your network. Enable DHCP Server :
100 DHCP IP Address Range :
to 200
(addresses within the LAN subnet) Always broadcast: Check this box if your clients are having difficulty obtaining an IP address. DHCP Lease Time :
Always broadcast : (compatibility for some DHCP Clients)
(minutes) 10080 ADD DHCP RESERVATION DHCP Reservation allows you to reserve IP addresses for specific machines based on their unique hardware MAC addresses. During DHCP IP address assignment, these devices will receive the same IP address. This is particularly useful if you run servers on your network. ADD DHCP RESERVATION Enable :
Computer Name :
<<
Computer Name IP Address :
MAC Address :
Clone Your PCs MAC Address Add / Update Clear Enable: Enable or disable DHCP reservation. Computer Name: Enter a name for your DHCP reservation rule. To easily add an IP reservation for an existing device select it from the drop down menu and click the << button. The fields will automatically populate. IP Address: Enter the IP address you wish to have assigned to this device. MAC Address: Enter the MAC address of the device you wish to apply the DHCP reservation rule to. Click Clone Your PCs MAC Address to fill this field. Click Add / Update when you are done. DHCP RESERVATIONS LIST DHCP RESERVATIONS LIST Enable Host Name IP Address The currently defined DHCP Reservations are listed here. Enable: Enable or disable this DHCP Reservation rule. Host Name: The host name for this rule. IP Address: The DHCP IP address reservation. D-Link DIR-815 User Manual 55 Section 3 - Configuration Network Settings (continued) MAC Address: The MAC address of the device. Edit Button: Click this button to edit this rules settings. Delete Button: Click this button to delete this DHCP IP Reservation. DHCP RESERVATIONS LIST Enable Host Name IP Address NUMBER OF DYNAMIC DHCP CLIENTS NUMBER OF DYNAMIC DHCP CLIENTS Host Name IP Address MAC Address Expired Time This section displays all of the currently connected DHCP cclients. The Host Name, IP address, MAC Address, and expiration time of each client is displayed in the table. Save Settings Dont Save Settings Click Save Settings when you are finished. D-Link DIR-815 User Manual 56 Section 3 - Configuration Storage Click Storage on the navigation menu to configure network access to files on an external USB device plugged into the router. Samba allows file and print sharing between computers. When you are satisfied with your configuration, click Save Settings. Refer Connect and Share a USB Storage Device on page 125 to for information on configuring your client computers to connect to your USB drive. WINDOWS FILE SHARING (SAMBA) Enable SAMBA: Enable or disable SAMBA file sharing. User Name: By default, the username for SAMBA is root. USER CREATION Password: Enter the password used to secure your fileshare. Click Save Settings when you are finished. DIR-815 STORAGE STORAGE SETUP STORAGE USB storage device using the Samba file sharing protocol. To use this feature, check the Enable SAMBA checkbox, then use the root account to manage access to your storage device. Save Settings Dont Save Settings WINDOWS FILE SHARING (SAMBA) USER CREATION Enable SAMBA:
User Name :
root Password :
123456 Save Settings Dont Save Settings D-Link DIR-815 User Manual 57 Section 3 - Configuration IPv6 Click IPv6 on the navigation menu to configure IPv6 connectivity. The IPv6 Internet Connection Setup Wizard allows you to quickly set up an IPv6 Internet connection which uses PPPoE, Static IP, or 6rd. See IPv6 Internet Connection Setup Wizard on page 59 for more information. To configure your router to use IPv6 locally on your LAN only see IPv6 Local Connectivity Settings on page 63. You may also manually configure your IPv6 connection. See Manual IPv6 Internet Connection Setup on page 64. DIR-815 IPV6 IPV6 INTERNET CONNECTION SETUP IPV6 INTERNET CONNECTION There are two ways to set up your IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually configure the connection. IPV6 INTERNET CONNECTION SETUP WIZARD If you would like to utilize our easy to use Web-based Wizard to assist you in connecting your new D-Link Systems Router to the IPv6 Internet, click on the button below. IPv6 Internet Connection Setup Wizard Note:Before launching the wizards, please make sure you have followed all steps outlined in the Quick Installation Guide included in the package. MANUAL IPV6 LOCAL CONNECTIVITY SETUP If you would like to configure the IPv6 local connectivity settings of your D-Link Router, then click on the button below. IPv6 Local Connectivity Settings MANUAL IPV6 INTERNET CONNECTION SETUP If you would like to configure the IPv6 Internet settings of your new D-Link Router manually, then click on the button below. Manual IPv6 Internet Connection Setup D-Link DIR-815 User Manual 58 Section 3 - Configuration IPv6 Internet Connection Setup Wizard The IPv6 Internet Connection Setup Wizard allows you to quickly set up an IPv6 Internet connection which uses PPPoE, Static IP, or 6rd. Click Next to begin. STEP 1: CONFIGURE YOUR IPV6 INTERNET CONNECTION Choose your IPv6 connection type and click Next. For IPv6 over PPPoE setup help refer to page 60. For Static IPv6 address and Route setup help refer to page 61. For Tunneling Connection (6rd) setup help refer to page 62. WELCOME TO THE D-LINK IPV6 INTERNET CONNECTION SETUP WIZARD This wizard will guide you through a step-by-step process to configure your new D-Link router and connect to the IPv6 Internet. Step 1: Configure your IPv6 Internet Connection Step 2: Save Settings and Connectnect Prev Next Cancel Connect STEP 1: CONFIGURE YOUR IPV6 INTERNET CONNECTION Please select your IPv6 Internet Connection type:
IPv6 over PPPoE Choose this option if your IPv6 Internet connection requires a username and password to get online. Most DSL modems use this type of connection. Static IPv6 address and Route Choose this option if your Internet Setup Provider (ISP) provided you with IPv6 Address information that has to be manually configured. Tunneling Connection (6rd) Choose this option if your Internet Setup Provider (ISP) provided you a IPv6 Internet Connection by using 6rd automatic tunneling mechanism. Prev Next Cancel Connect D-Link DIR-815 User Manual 59 Section 3 - Configuration IPv6 Internet Connection Setup Wizard IPv6 over PPPoE If you choose IPv6 over PPPoE as your Internet Connection, enter your IP address, configure the following settings:
SET USERNAME AND PASSWORD CONNECTION (PPPOE) SET USERNAME AND PASSWORD CONNECTION (PPPOE) To set up this connection you will need to have a Username and Password from your IPv6 Internet Service Provider. If you do not have this information, please contact your ISP. PPPoE Session : Select whethe to Share with IPv4 or Create a new session. If you choose Create a new session as the PPPoE Session, fill in the following fields:
Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. Service Name: Enter the ISP service name (optional). Click Next to continue. PPPoE Session : Share with IPv4 Create a new session User Name :
Password :
Verify Password :
Service Name :
(optional) Note: You may also need to provide a Service Name. If you do not have or know this information, please contact your ISP. Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot the router. Prev Next Cancel Connect D-Link DIR-815 User Manual 60 Section 3 - Configuration IPv6 Internet Connection Setup Wizard Static IPv6 address and Route If you choose Static IPv6 address and Route as your Internet Connection, enter your IP address, configure the following settings:
SET STATIC IPV6 ADDRESS CONNECTION SET STATIC IPV6 ADDRESS CONNECTION To set up this connection you will need to have a complete list of IPv6 information provided by your IPv6 Internet Service Provider. If you have a Static IPv6 connection and do not have this information, please contact your ISP. Use Link-Local Address:
Enable or disable using the Link-Local Address. The IPv6 Address and Subnet Prefix Length is automatically populated with this function. IPv6 Address: Enter the address supplied by your ISP. Subnet Prefix Length:
Enter the subnet prefix length supplied by your ISP. Default Gateway: Enter the default gateway for your IPv6 connection. Primary IPv6 DNS Address:
Secondary IPv6 DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. LAN IPv6 Address: Enter your the LAN IPv6 Address you want to use. Click Next to continue. Use Link-Local Address :
IPv6 Address :
Subnet Prefix Length :
Default Gateway :
Primary IPv6 DNS Address :
Secondary IPv6 DNS Address :
LAN IPv6 Address :
Prev Next Cancel Connect Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot the router. Prev Next Cancel Connect D-Link DIR-815 User Manual 61 Section 3 - Configuration IPv6 Internet Connection Setup Wizard Tunneling Connection (6rd) If you choose Tunneling Connection (6rd) as your Internet Connection, enter your IP address, configure the following settings:
SET UP 6RD TUNNELING CONNECTION SET UP 6RD TUNNELING CONNECTION To set up this 6rd tunneling connection you will need to have the following information from your IPv6 Internet Service Provider. If you do not have this information, please contact your ISP. 6rd IPv6 Prefix: Enter the 6rd IPv6 prefix and mask length supplied by your ISP. IPv4 Address: Displays the routers IPv4 address and mask length. Assigned IPv6 Prefix:
6rd Border Relay IPv4 Address:
Displays the routers assigned IPv6 prefix. Enter the 6rd border relay IPv4 address settings supplied by your ISP. 6rd IPv6 Prefix :
IPv4 Address :
Assigned IPv6 Prefix :
6rd Border Relay IPv4 Address :
Primary IPv6 DNS Address :
/
Mask Length :
Prev Next Cancel Connect IPv6 DNS Server: Enter the IPv6 DNS server address. Click Next to continue. Click Connect to finish the setup. SETUP COMPLETE!
SETUP COMPLETE!
The IPv6 Internet Connection Setup Wizard has completed. Click the Connect button to save your settings and reboot the router. Prev Next Cancel Connect D-Link DIR-815 User Manual 62 Section 3 - Configuration IPv6 Local Connectivity Settings Click the IPv6 Local Connectivity Settings button to configure IPv6 on your local network. When you are satisfied with your configuration, click Save Settings. Enable ULA: Enable or disable ULA. IPV6 ULA SETTINGS DIR-815 IPV6 SETUP IPV6 LOCAL CONNECTIVITY SETTINGS Use default ULA prefix:
Enable or disable the use of the default ULA prefix. IPV6 LOCAL CONNECTIVITY SETTINGS Use this section to configure Unique Local IPv6 Unicast Address (ULA) settings for your router.ULA is intended for local communications and not expected to be routable on the global Internet. If you enabled ULA, enter your ULA prefix:
ULA Prefix: Enter your ULA prefix. IPV6 ULA SETTINGS The current ULA Prefix is displayed here. Current ULA Prefix:
LAN IPv6 ULA: The current LAN IPv6 ULA is displayed here. When you have finished configuring your IPv6 connection, click the Save Settings button. Save Settings Dont Save Settings IPV6 ULA SETTINGS Enable ULA :
Use default ULA prefix :
Use default ULA prefix :
CURRENT IPV6 ULA SETTINGS Current ULA Prefix :
/64 LAN IPv6 ULA :
/64 Save Settings Dont Save Settings
/64 D-Link DIR-815 User Manual 63 Section 3 - Configuration Manual IPv6 Internet Connection Setup Click the Manual IPv6 Internet Connection Setup button to manually configure your IPv6 connection to your ISP. When you are satisfied with your configuration, click Save Settings. IPV6 INTERNET CONNECTION SETUP WIZARD My IPv6 Connection is:
Choose your IPv6 connection type from the drop-down menu. You will be presented with the appropriate options for your connection type. DIR-815 IPV6 IPV6 SETUP IPV6 For Static IPv6 refer to page 65. For Autoconfiguration(SLAAC/DHCPv6) refer to page 67. For PPPoE refer to page 69. For IPv6 in an IPv4 Tunnel refer to page 72. For 6to4 refer to page 75. For 6rd refer to page 77. For Local Connectivity Only refer to page 79. When you have finished configuring your IPv6 connection, click the Save Settings button. Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
Static IPv6 Autoconfiguration(SLAAC/DHCPv6) PPPoE IPv6 in IPv4 Tunnel 6to4 6rd Local Connectivity Only D-Link DIR-815 User Manual 64 Section 3 - Configuration Static IPv6 IPV6 CONNECTION TYPE Select Static IPv6 if your IPv6 information is provided by your ISP. My IPv6 Connection is:
WAN IPV6 ADDRESS SETTINGS Use Link-Local Address:
Enable or disable using the Link-Local Address. The IPv6 Address and Subnet Prefix Length is automatically populated with this function. IPv6 Address: Enter the address supplied by your ISP. Subnet Prefix Length:
Enter the subnet prefix length supplied by your ISP. Default Gateway: Enter the default gateway for your IPv6 connection. Primary DNS Address:
Secondary DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Address Settings LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
Static IPv6 WAN IPV6 ADDRESS SETTINGS Enter the IPv6 address information provided by your Internet Service Provider (ISP). Use Link-Local Address :
IPv6 Address :
Subnet Prefix Length :
Default Gateway :
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings D-Link DIR-815 User Manual 65 Section 3 - Configuration Static IPv6 (continued) ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement LIfetime :
(minutes) Save Settings Dont Save Settings ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement LIfetime :
(minutes)
:00
:00 1 ff Save Settings Dont Save Settings Enable Automatic IPv6 address assignment:
Autoconfiguration Type:
Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Advertisement Lifetime:
Enter the IPv6 address lifetime (in minutes). If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
Enter the starting IPv6 address for the DHCP servers IPv6 assignment. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. Enter the IPv6 address lifetime (in seconds). When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 66 Section 3 - Configuration Autoconfiguration(SLAAC/DHCPv6) IPV6 CONNECTION TYPE My IPv6 Connection is:
Select Autoconfiguration(SLAAC/DHCPv6) if your ISP assigns your IPv6 address when your router requests one from the ISPs server. Some ISPs require you to adjust settings on your side before your router can connect to the IPv6 Internet. Select either Obtain DNS server address automatically or Use the following DNS address. IPV6 DNS SETTINGS DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
Autoconfiguration(SLAAC/DHCPv6) If you choose Use the following DNS address, please configure the following field:
IPV6 DNS SETTINGS Primary DNS Address:
Secondary DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. Enable DHCP-PD: Check this box to enable DHCP-PD. LAN IPv6 Address Settings LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. Obtain DNS server address automatically or enter a specific DNS server address. Obtain IPv6 DNS Servers automatically Use the following IPv6 DNS Servers Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. Enable DHCP-PD :
LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings D-Link DIR-815 User Manual 67 Section 3 - Configuration Autoconfiguration(SLAAC/DHCPv6) (continued) Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Enable Automatic IPv6 address assignment:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Enable Automatic DHCP-PD in LAN:
Enable or disable the Automatic IPv6 Address Assignment feature for the LAN. Save Settings Dont Save Settings Autoconfiguration Type:
Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. If you choose SLAAC+Stateless DHCP, the following field appears:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement Lifetime :
(minutes)
:00
:00 1 ff The currently defined router advertisement lifetime is displayed. Save Settings Dont Save Settings Router Advertisement Lifetime:
If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
Enter the starting IPv6 address for the DHCP servers IPv6 assignment. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. The currently defined router advertisement lifetime is displayed. When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 68 Section 3 - Configuration PPPoE IPV6 CONNECTION TYPE My IPv6 Connection is:
Select PPPoE if your ISP provides and requires you to enter a PPPoE username and password in order to connect to the Internet. PPPOE INTERNET CONNECTION TYPE :
PPPoE Session : Select whethe to Share with IPv4 or Create a new session. Address Mode: Select either Dynamic IP or Static IP. If you chose Share with IPv4 as the PPPoE Session with Static IP as the Address Mode, enter your IP address:
IP Address: Enter the IP address provided by your ISP. If you choose Create a new session as the PPPoE Session, fill in the following fields:
Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Verify Password: Enter the password provided by your ISP one more time. Service Name: Enter the ISP service name (optional). Reconnect Mode: Select either AlwaysOn or Manual. Maximum Idle Time:
Set the length of time to wait before disconnecting if there is no Internet activity. (Manual Only) MTU Size: Enter the MTU size. D-Link DIR-815 User Manual DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
PPPoE PPPOE INTERNET CONNECTION TYPE :
Enter the information provided by your Internet Service Provider (ISP). PPPoE Session : Share with IPv4 Create a new session Address Mode : Dynamic IP Static IP IP Address :
User Name :
Password :
Verify Password :
Service Name :
(optional) Reconnect Mode : Always on On Demand Manual Maximum Idle Time :
(minutes, 0=infinite) MTU :
1492
(byes) MTU default=1492 IPV6 DNS SETTINGS Obtain DNS server address automatically or enter a specific DNS server address. Obtain IPv6 DNS Servers automatically Use the following IPv6 DNS Servers Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. Enable DHCP-PD :
LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) 69 Section 3 - Configuration PPPoE (continued) Select either Obtain DNS server address automatically or Use the following DNS address. Obtain IPv6 DNS Servers automatically Use the following IPv6 DNS Servers IPV6 DNS SETTINGS IPV6 DNS SETTINGS Obtain DNS server address automatically or enter a specific DNS server address. If you choose Use the following DNS address, please configure the following field:
Primary DNS Address:
Secondary DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. LAN IPv6 Address Settings Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. Enable DHCP-PD :
LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) If you chose Dynamic IP as the Address Mode, you have the option to enable DHCP-PD appears:
Save Settings Dont Save Settings Enable DHCP-PD: Check this box to enable DHCP-PD. If you chose Static IP as the Address Mode, or disabled DHCP-PD, enter your LAN IPv6 Address:
LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. D-Link DIR-815 User Manual 70 Section 3 - Configuration PPPoE (continued) Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Enable Automatic IPv6 address assignment:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement LIfetime :
(minutes) Save Settings Dont Save Settings If you chose Dynamic IP as the Address Mode and enabled DHCP-PD in LAN IPv6 Address Settings, you may enable DHCP-PD for the LAN:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic DHCP-PD in LAN:
Enable or disable the Automatic IPv6 Address Assignment feature for the LAN. Autoconfiguration Type:
Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings If you choose SLAAC+Stateless DHCP, the following field appears:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Router Advertisement Lifetime:
The currently defined router advertisement lifetime is displayed. If you choose Stateful DHCPv6, please configure the following fields:
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings
:00
:00 1 ff Enter the starting IPv6 address for the DHCP servers IPv6 assignment. ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. The currently defined router advertisement lifetime is displayed. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement LIfetime :
(minutes)
:00
:00 1 ff Save Settings Dont Save Settings IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 71 Section 3 - Configuration IPv6 in an IPv4 Tunnel IPV6 CONNECTION TYPE My IPv6 Connection is:
Select IPv6 In IPv4 Tunnel if you wish to configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunnelling encapsulates IPv6 packets in IPv4 packets so that IPv6 packets can be sent over an IPv4 infrastructure. IPv6 in IPv4 Tunnel Settings Enter the IPv4 remote address. Enter the IPv6 remote address. Displays the current local IPv4 address. Enter the IPv6 local address. Enter the IPv6 subnet prefix length. Remote IPv4 Address:
Remote IPv6 Address:
Local IPv4 Address:
Local IPv6 Address:
Subnet Prefix Length:
DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
IPv6 in IPv4 Tunnel IPV6 IN IPV4 TUNNEL SETTINGS Enter the information provided by your Internet Service Provider (ISP). Remote IPv4 Address :
Remote IPv6 Address :
Local IPv4 Address :
Local IPv6 Address :
Subnet Prefix Length :
IPV6 DNS SETTINGS Obtain DNS server address automatically or enter a specific DNS server address. Obtain IPv6 DNS Servers automatically Use the following IPv6 DNS Servers Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. Enable DHCP-PD :
LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) D-Link DIR-815 User Manual 72 Section 3 - Configuration IPv6 in and IPv4 Tunnel (continued) Select either Obtain DNS server address automatically or Use the following DNS address. Obtain IPv6 DNS Servers automatically Use the following IPv6 DNS Servers IPV6 DNS SETTINGS IPV6 DNS SETTINGS Obtain DNS server address automatically or enter a specific DNS server address. If you choose Use the following DNS address, please configure the following field:
Primary DNS Address:
Secondary DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. Enable DHCP-PD: Check this box to enable DHCP-PD. LAN IPv6 Address Settings LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. Not available if DHCP-PD is enabled. LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. Enable DHCP-PD :
LAN IPv6 Address :
/64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings D-Link DIR-815 User Manual 73 Section 3 - Configuration IPv6 in an IPv4 Tunnel (continued) Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Enable Automatic IPv6 address assignment:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement LIfetime :
(minutes) Save Settings Dont Save Settings If you enabled DHCP-PD in LAN IPv6 Address Settings, you may enable DHCP-PD for the LAN:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Enable Automatic DHCP-PD in LAN:
Enable or disable the Automatic IPv6 Address Assignment feature for the LAN. Autoconfiguration Type:
Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings If you choose SLAAC+Stateless DHCP, the following field appears:
ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. You can also enable DHCP-PD to delegate prefixes for routers in your LAN. Router Advertisement Lifetime:
The currently defined router advertisement lifetime is displayed. If you choose Stateful DHCPv6, please configure the following fields:
Enable Automatic IPv6 address assignment :
Enable Automatic DHCP-PD in LAN :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings
:00
:00 1 ff Enter the starting IPv6 address for the DHCP servers IPv6 assignment. ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. The currently defined router advertisement lifetime is displayed. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement LIfetime :
(minutes)
:00
:00 1 ff Save Settings Dont Save Settings IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 74 Section 3 - Configuration 6to4 IPV6 CONNECTION TYPE My IPv6 Connection is:
Select IPv6 In IPv4 Tunnel if you wish to configure your router to connect to your ISP using 6 to 4. 6 to 4 is an IPv6 address assignment and automatic tunneling technology that is used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet. DIR-815 IPV6 IPV6 SETUP IPV6 WAN IPV6 ADDRESS SETTINGS 6to4 Address: The current 6to4 address is displayed here. 6to4 Relay: Enter the 6 to 4 relay address supplied by your ISP. Primary DNS Address:
Secondary DNS Address:
Enter the primary DNS server address. Enter the secondary DNS server address. LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Address Settings LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
6to4 WAN IPV6 ADDRESS SETTINGS Enter the IPv6 address information provided by your Internet Service Provider (ISP). 6to4 Address :
6to4 relay :
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. LAN IPv6 Address : XXXX:XXXX:XXXX:
::1 /64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings D-Link DIR-815 User Manual 75 Section 3 - Configuration ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement LIfetime :
(minutes) Save Settings Dont Save Settings ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
Stateful DHCPv6 IPv6 Address Range (Start) :
IPv6 Address Range (End) :
Router Advertisement LIfetime :
(minutes)
:00
:00 1 ff Save Settings Dont Save Settings 6to4 (continued) Enable Automatic IPv6 address assignment:
Autoconfiguration Type:
Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Advertisement Lifetime:
Enter the IPv6 address lifetime (in minutes). If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
Enter the starting IPv6 address for the DHCP servers IPv6 assignment. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. Enter the IPv6 address lifetime (in seconds). When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 76 Section 3 - Configuration 6rd IPV6 CONNECTION TYPE Select 6rd if your ISP uses the 6rd IPv6 connection protocol. My IPv6 Connection is:
6rd Configuration: Select either 6rd DHCPv4 or Manual Configuration. WAN IPV6 ADDRESS SETTINGS If you selected Manual Configuration, fill in the following fields:
DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
6rd 6rd IPv6 Prefix: Enter the 6rd IPv6 prefix and mask length supplied by your ISP. WAN IPV6 ADDRESS SETTINGS IPv4 Address: Displays the routers IPv4 address and mask length. Assigned IPv6 Prefix:
Tunnel Link-Local Address:
6rd Border Relay IPv4 Address:
Primary DNS Address:
Secondary DNS Address:
Displays the routers assigned IPv6 prefix. Displays the tunnel link-local address. Enter the 6rd border relay IPv4 address settings supplied by your ISP. Enter the primary DNS server address. Enter the secondary DNS server address. Enter the IPv6 address information provided by your Internet Service Provider (ISP). 6rd Configuration : 6rd DHCPv4 option Manual Configuration
/
Mask Length :
6rd IPv6 Prefix :
IPv4 Address :
Assigned IPv6 Prefix :
Tunnel Link-Local Address :
6rd Border Relay IPv4 Address :
Primary DNS Address :
Secondary DNS Address :
LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. LAN IPv6 Address : XXXX:XXXX:XXXX:
::1 /64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPV6 ADDRESS SETTINGS D-Link DIR-815 User Manual 77 Section 3 - Configuration 6rd (continued) LAN IPv6 Link-
Local Address:
Displays the routers LAN link-local address. LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. If you change the LAN IPv6 Address here, you may need to adjust your PC network settings to access the network again. LAN IPv6 Address : XXXX:XXXX:XXXX:
::1 /64 LAN IPv6 Link-Local Address :
ffff::fff:ffff:ffff:1234 /64 Enable Automatic IPv6 address assignment:
Autoconfiguration Type:
Address Autoconfiguration Settings Enable or disable the Automatic IPv6 Address Assignment feature. If you disable this option, no further configuration is available. Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. ADDRESS AUTOCONFIGURATION SETTINGS Use this section to setup IPv6 Autoconfiguration to assign IP addresses to the computers on your network. Enable Automatic IPv6 address assignment :
Autoconfiguration Type :
SLAAC+RDNSS SLAAC+Stateless DHCP Stateful DHCPv6 Router Advertisement Lifetime :
(minutes) Save Settings Dont Save Settings If you choose SLAAC+Stateless DHCP, please configure the following field:
Router Advertisement Lifetime:
Enter the IPv6 address lifetime (in minutes). If you choose Stateful DHCPv6, please configure the following fields:
IPv6 Address Range(Start):
IPv6 Address Range(End):
Router Advertisement Lifetime:
Enter the starting IPv6 address for the DHCP servers IPv6 assignment. Enter the ending IPv6 address for the DHCP servers IPv6 assignment. Enter the IPv6 address lifetime (in seconds). When you have finished configuring your IPv6 connection, click the Save Settings button. D-Link DIR-815 User Manual 78 Section 3 - Configuration Local Connectivity Only IPV6 CONNECTION TYPE My IPv6 Connection is:
Select Local Connectivity Only allows you to set up a local IPv6 connection that does not connect to the Internet. IPV6 CONNECTION TYPE Displays the routers LAN IPv6 Link-Local address and mask length. LAN IPv6 Link-
Local Address :
LAN IPv6 Unique Local Address :
When you have finished configuring your IPv6 connection, click the Save Settings button. DIR-815 IPV6 IPV6 SETUP IPV6 Use this section to configure your IPv6 Connection Type.If you are unsure of your connection method, please contact your Internet Service Provider. Save Settings Dont Save Settings IPV6 CONNECTION TYPE LAN IPV6 ADDRESS SETTINGS Use this section to configure the internal network settings of your router. LAN IPv6 Link-Local Address : XXXX:XXXX:XXXX:XXXX / 64 LAN IPv6 Unique Local Address :
ffff::fff:ffff:ffff:1234 /64 Save Settings Dont Save Settings Displays the routers LAN IPv6 unique local address and mask length. Choose the mode to be used by the router to connect to the IPv6 Internet. My IPv6 Connection is:
Local Connectivity Only D-Link DIR-815 User Manual 79 Section 3 - Configuration The Advanced tab provides access to configure the advanced features of your DIR-815. Advanced SETUP ADVANCED TOOLS STATUS SUPPORT DIR-815 VIRTUAL SERVER PORT FORWARDING APPLICATION RULES QOS ENGINE NETWORK FILTER INBOUND FILTER ACCESS CONTROL WEBSITE FILTER FIREWALL SETTINGS ROUTING ADVANCED WIRELESS WI-FI PROTECTED SETUP ADVANCED NETWORK GUEST ZONE IPV6 FIREWALL IPV6 ROUTING To return to the Web UI Table of Contents page, simply click the D-Link logo on the top right of each page. DIR-815 INTERNET SETUP INTERNET CONNECTION D-Link DIR-815 User Manual 80 Section 3 - ConfigurationVIRTUAL SERVERThe Virtual Server option allows you to define a single public port on your router for redirection to an internal LAN IP Address and Private LAN port if required.This feature is useful for hosting online services such as FTP or Web Servers.Save SettingsDont Save Settings24 - VIRTUAL SERVERS LISTRemaining number of rules that can be created: 24PortTraffic TypeName<< Application NamePublic PortProtocol TCPScheduleAlwaysIP Address<< Computer NamePrivate Port6Inbound FilterAllow AllSave SettingsDont Save Settings Virtual Server Click Virtual Server on the navigation menu to configure the virtual server. The virtual server performs port-redirection, which allows remote users to access multiple services on your local network via your public IP address. For example, you may want to connect two FTP servers on two different machines on your local network to the Internet. Using Port Forwarding only allows a single machine use port 21, but with port forwarding you can remap two different external ports to each machine. When you are satisfied with your configuration, click Save Settings. 24 - VIRTUAL SERVERS LIST Enable: Check the box to enable this rule. Name: Enter a name for the application you wish to apply the virtual server to. Use the Application Name dropdown menu and the << button to quickly select commonly used applications. The name, private port, public port, and protocol type are automatically populated. Public Port: Enter or adjust the WAN port number in order to remap traffic. Protocol: Select TCP or UDP from the Protocol drop-down menu. Schedule: Select the schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to or use the Computer Name dropdown menu and the << button to quickly insert a devices IP address. Private Port: Enter the LAN port number. Inbound Filter: You may set the traffic filter to Allow All or Block All traffic. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual DIR-815 ADVANCED VIRTUAL SERVER VIRTUAL SERVER VIRTUAL SERVER The Virtual Server option allows you to define a single public port on your router for redirection to an internal LAN IP Address and Private LAN port if required.This feature is useful for hosting online services such as FTP or Web Servers. Save Settings Dont Save Settings 24 - VIRTUAL SERVERS LIST Remaining number of rules that can be created: 24 Name IP Address
<< Application Name
<< Computer Name Port Public Port Private Port Traffic Type Protocol TCP 6 Schedule Always Inbound Filter Allow All Save Settings Dont Save Settings 81 Section 3 - Configuration Port Forwarding Click Port Forwarding on the navigation menu to configure Port Forwarding. Port Forwarding allows you to expose devices, applications, and servers on your local network to the Internet. When you are satisfied with your configuration, click Save Settings. 24 -- PORT FORWARDING RULES Enable: Check the box to enable this rule. Name: Enter a name for the application you wish to apply the virtual server to. Use the Application Name dropdown menu and the << button to quickly select an application. The name, TCP port, and UDP port are automatically populated. TCP: Enter the TCP port number to forward. Schedule: Select the schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to or use the Computer Name dropdown menu and the << button to quickly insert a devices IP address. UDP: Enter the UDP port number to forward. Inbound Filter: You may set the traffic filter to Allow All or Block All traffic. Click the Save Settings button when you are finished. DIR-815 ADVANCED PORT FORWARDING PORT FORWARDING PORT FORWARDING This option is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on your network. This feature allows you to enter ports in the format, Port Ranges (100-150), Individual Ports (80, 68, 888), or Mixed
(1020-5000, 689). This option is only applicable to the INTERNET session. Save Settings Dont Save Settings 24 -- PORT FORWARDING RULES Remaining number of rules that can be created: 24 Name IP Address Ports to Open TCP
<< Application Name
<< Computer Name UDP Schedule Always Inbound Filter Allow All Save Settings Dont Save Settings D-Link DIR-815 User Manual 82 Section 3 - Configuration Application Rules Click Port Triggering on the navigation menu to configure Port Triggering. Port triggering allows external ports to be opened for remote access when triggered by activity by a local computer on specified ports. When you are satisfied with your configuration, click Save Settings. 24 -- APPLICATION RULES Enable: Check the box to enable this rule. Name: Enter a name for the application you wish to apply the virtual server to. Use the Application Name dropdown menu and the << button to quickly select an application. The name, port numbers, and traffic type are automatically populated. Trigger Port: Enter the trigger port. Traffic Type: Select TCP, UDP, or All. Firewall Port: Enter the firewall port to open once triggered. Traffic Type: Select TCP, UDP, or All. Schedule: Select the schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. Click the Save Settings button when you are finished. DIR-815 ADVANCED APPLICATION RULES APPLICATION RULES APPLICATION RULES The Application Rules option is used to open single or multiple ports in your firewall when the router senses data sent to the Internet on an outgoing "Trigger" port or port range. Special Application rules apply to all computers on your internal network. Save Settings Dont Save Settings 24 -- APPLICATION RULES Remaining number of rules that can be created: 24 Name Application <<
Application Name Save Settings Dont Save Settings Port Trigger Firewall Traffic Type TCP TCP Schedule Always D-Link DIR-815 User Manual 83 Section 3 - Configuration QOS Engine Click QoS Engine on the navigation menu to configure Quality of Service (QoS). QoS allows you to prioritize Internet traffic to ensure a better web browsing experience in situations where bandwidth is limited or large numbers of devices are in use. QoS can improve your online experience by ensuring that specific traffic is prioritized over other network traffic, such as VoIP, FTP, or Web. When you are satisfied with your configuration, click Save Settings. Enable QoS: Enable or disable QoS. QOS SETUP Uplink Speed: Enter your Internet connections Uplink Speed in kbps or use the Select Transmission Rate dropdown menu and the << button to quickly select and populate a speed. Downlink Speed: Enter your Internet connections Downlink Speed in kbps or use the Select Transmission Rate dropdown menu and the << button to quickly select and populate a speed. Queue Type: Choose either Strict Priority Queue or Weighted Fair Queue. If you select Weighted Fair Queue, you may adjust the percentage weights for each queue. Click the Save Settings button before proceeding to 32 -- ADD CLASSIFICATION RULE. DIR-815 QOS ENGINE QOS SETTINGS ADVANCED QOS SETTINGS Use this section to configure D-Link's QoS Engine powered by QoS Engine Technology. This QoS Engine improves your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web.For best performance, use the Automatic Classification option to automatically set the priority for your applications. Save Settings Dont Save Settings QOS SETUP Enable Qos :
Uplink Speed :
0 kbps <<
Select Transmission Rate Downlink Speed :
0 kbps <<
Select Transmission Rate Queue Type : Strict Priority Queue Weighted Fair Queue Queue ID Queue Priority 1 2 3 4 32 -- ADD CLASSIFICATION RULE Highest Higher Normal Best Effort(default) Enable :
Name :
Queue ID :
1 - Highest Protocol :
ALL Classify :
Upstream Local IP Range : Local IP Start Local IP End Application Port :
Application Name >>
Remote IP Range : Remote IP Start Add Cancel to to to Remote IP End CLASSIFICATION RULES Enable Name Queue ID Protocol Classify Application Port Remote IP Range Local IP Range Save Settings Dont Save Settings D-Link DIR-815 User Manual 84 Section 3 - Configuration QOS Engine (continued) 32 -- ADD CLASSIFICATION RULE Enable: Check the box to enable this rule. Name: Enter a name for this QoS rule. Queue ID: Select the queue to apply this rule to. Protocol: Select the protocol to apply the rule to: TCP, UDP, or All. DIR-815 QOS ENGINE QOS SETTINGS ADVANCED QOS SETTINGS Use this section to configure D-Link's QoS Engine powered by QoS Engine Technology. This QoS Engine improves your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web.For best performance, use the Automatic Classification option to automatically set the priority for your applications. Save Settings Dont Save Settings Classify: Select to apply the rule to Upstream or Downstream traffic. QOS SETUP Local IP Range: If you selected Upstream as the Classify type, enter the local IP Range, excluding the router IP and broadcast IP, to apply this rule to. For example 192.168.0.2 to 192.168.0.254. Application Port: Enter the port range you wish to apply this rule to. Use the Application Name dropdown menu and the << button to quickly select an application. The protocol, and port range are automatically populated. Remote IP Range: If you selected Downstream as the Classify type, enter the Remote IP Range, excluding the router IP and broadcast IP, to apply this rule to. For example 192.168.0.2 to 192.168.0.254. CLASSIFICATION RULES The currently defined QoS rules are listed here. Click the Save Settings button when you are finished. Enable Qos :
Uplink Speed :
0 kbps <<
Select Transmission Rate Downlink Speed :
0 kbps <<
Select Transmission Rate Queue Type : Strict Priority Queue Weighted Fair Queue Queue ID Queue Priority 1 2 3 4 32 -- ADD CLASSIFICATION RULE Highest Higher Normal Best Effort(default) Enable :
Name :
Queue ID :
1 - Highest Protocol :
ALL Classify :
Upstream Local IP Range : Local IP Start Local IP End Application Port :
Application Name >>
Remote IP Range : Remote IP Start Add Cancel to to to Remote IP End CLASSIFICATION RULES Enable Name Queue ID Protocol Classify Application Port Remote IP Range Local IP Range Save Settings Dont Save Settings D-Link DIR-815 User Manual 85 Section 3 - Configuration Network Filter Click Network Filter on the navigation menu to configure the Network Filter. The Network Filter allows you to allow or block a devices access to the network or Internet based on its MAC address. When you are satisfied with your configuration, click Save Settings. 24 -- MAC FILTERING RULES Configure MAC Filtering below:
Select the function of the MAC Filter, the options are Turn MAC Filtering OFF, Turn MAC Filtering ON and ALLOW rules listed, or Turn MAC Filtering ON and DENY rules listed. Enable: Check the box to enable this rule. MAC Address: Enter the MAC Address of the device you wish to apply the Network Filter to. Use the Computer Name dropdown menu and the <<
button to quickly select a device. The MAC Address is automatically populated. Schedule: Select the schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. Click the Save Settings button when you are finished. DIR-815 ADVANCED NETWORK FILTER MAC ADDRESS FILTER MAC ADDRESS FILTER The MAC (Media Access Controller) Address filter option is used to control network access based on the MAC Address of the network adapter.A MAC address is a unique ID assigned by the manufacturer of the network adapter.This feature can be configured to ALLOW or DENY network/Internet access. Save Settings Dont Save Settings 24 -- MAC FILTERING RULES Configure MAC Filtering below:
Turn MAC Filtering OFF Turn MAC Filtering ON and ALLOW rules listed Turn MAC Filtering ON and DENY rules listed Remaining number of rules that can be created: 24 MAC Address DHCP Client List Schedule
<<
Computer Name Always New Schedule Save Settings Dont Save Settings D-Link DIR-815 User Manual 86 Section 3 - Configuration Inbound Filter Click Inbound Filter on the navigation menu to configure the Inbound Filter. The Inbound Filter allows you to place filtering rules on a per IP basis. Using this tool you may restrict access to or block traffic to a specific remote IP address or range. When you are satisfied with your configuration, click Save Settings. ADD INBOUND FILTER RULE Name: Enter a name for this Inbound Filter. Action: Allow or Deny traffic. Remote IP Range Enable: Check the box to enable this rule. Remote IP Start: Enter the starting IP address to apply the rule to. Remote IP End: Enter the ending IP address to apply the rule to. The currently defined Inbound Filter rules are listed here. INBOUND FILTER RULES LIST Click the Save Settings button when you are finished. DIR-815 ADVANCED INBOUND FILTER INBOUND FILTER ORANGE OrangeText Save Settings Dont Save Settings ADD INBOUND FILTER RULE Name :
Action :
Allow Remote IP Range : Enable Remote IP Start Remote IP End 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 INBOUND FILTER RULES LIST Name Action Remote IP Range Add Cancel D-Link DIR-815 User Manual 87 Section 3 - Configuration Access Control Click Access Control on the navigation menu to configure Access Control. The Access Control function allows you to control access to the Internet. You may also monitor which web sites were accessed. The Add Policy Wizard allows you to easily add access control policies. When you are satisfied with your configuration, click Save Settings. ACCESS CONTROL Enable Access Control:
Enable or disable Access Control. You must click Save Settings after enabling Access Control before you can add policies. Add Policy: Click this button to add a policy. Refer to Add Policy on page 89 for more information on running the Add Policy Wizard. POLICY TABLE The currently defined access control policies are listed in this table. Click the Save Settings button when you are finished. DIR-815 ADVANCED ACCESS CONTROL ACCESS CONTROL ACCESS CONTROL The Access Control option allows you to control access in and out of your network. Use this feature as Access Controls to only grant access to approved sites, limit web access based on time or dates, and/or block Internet access for applications like P2P utilities or games. Save Settings Dont Save Settings ACCESS CONTROL POLICY TABLE Enable Access Control :
Add Policy Enable Policy Machine Filtering Logged Schedule Save Settings Dont Save Settings D-Link DIR-815 User Manual 88 Section 3 - Configuration Click Next to begin the add policy wizard. ADD NEW POLICY Add Policy ADD NEW POLICY This wizard will guide you through the following steps to add a new policy for Access Control. Step 1 - Choose a unique name for your policy Step 2 - Select a schedule Step 3 - Select the machine to which this policy applies Step 4 - Select filtering method Step 5 - Select filters Step 6 - Configure Web Access Logging STEP 1: CHOOSE POLICY NAME STEP 1: CHOOSE POLICY NAME Choose a unique name for your policy. Policy Name : Enter a name for your policy. Click Next to continue. Prev Next Save Cancel Policy Name :
Prev Next Save Cancel STEP 2: SELECT SCHEDULE STEP 2: SELECT SCHEDULE Choose a schedule to apply to this policy. Details: Select a schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. Always Details :
Always Prev Next Save Cancel Click Next to continue. Address Type: Choose whether this policy is applied by IP or MAC address. STEP 3: SELECT MACHINE IP Address: If you select IP as the address type, enter the IP address of the device you wish to apply the policy to or use the Computer Name dropdown menu to quickly select a computer. The IP address is automatically populated. Machine STEP 3: SELECT MACHINE Select the machine to which this policy applies. Specify a machine with its IP or MAC address. Address Type : IP MAC IP Address :
Machine Addres :
<<
<<
Computer Name Computer Name Clone Your PCs MAC Address Add Cancel Prev Next Save Cancel D-Link DIR-815 User Manual 89 Section 3 - Configuration Add Policy (continued) Machine Address: If you select MAC as the address type, enter the IP address of the device you wish to apply the policy to or use the Computer Name dropdown menu to quickly select a computer. The MAC address is automatically populated. You may also use the Clone Your PCs MAC Address button to use the MAC address of the device you are running the wizard from. STEP 3: SELECT MACHINE Select the machine to which this policy applies. Specify a machine with its IP or MAC address. Add: Click this button to add the machine to the table. Machine Cancel: Click this button to clear the currently configured information Machine IP or MAC Address: To edit a machine added to the table, click its corresponding pencil icon. To remove a machine click its corresponding trashcan icon. Click Next to continue. Address Type : IP MAC IP Address :
Machine Addres :
<<
<<
Computer Name Computer Name Clone Your PCs MAC Address Add Cancel Prev Next Save Cancel STEP 4: SELECT FILTERING METHOD STEP 4: SELECT FILTERING METHOD Select the method for filtering. Method: Select the method for filtering. The available options are Log Web Access Only, Block All Access, or Block Some Access. Method : Log Web Access Only Block All Access Block Some Access Prev Next Save Cancel If you select Log Web Access Only or Block Some Access, click Save to finish the wizard. STEP 4: SELECT FILTERING METHOD Select the method for filtering. If you select Block Some Access, select the following options:
Apply Web Filter: Check this box to enable Web Access Logging. Apply Advanced Port Filters:
Check this box to enable port filtering. Click Next to continue. D-Link DIR-815 User Manual Method : Log Web Access Only Block All Access Block Some Access Apply Web Filter :
Apply Advanced Port Filters :
Prev Next Save Cancel 90 Section 3 - Configuration Add Policy (continued) If you selected Block Some Access, configure the following options:
STEP 5: PORT FILTER Enable: Check the box to enable this rule. Name: Enter a name for port filtering rule. Dest IP Start: Enter the start of the IP address range to filter. Dest IP End: Enter the end of the IP address range to filter. Protocol: Select the protocol to apply the port filter to. The options are Any, ICMP, TCP, and UDP. If you select TCP or UDP, enter the port range:
Des Port Start: Enter the start of the port range to filter. Des Port End: Enter the end of the port range to filter. Click Next to continue. STEP 5: PORT FILTER Add Port Filters Rules. Specify rules to prohibit access to specific IP addresses and ports. Enable Name Dest IP Start Dest IP End Protocol Dest Port Start Dest Port End 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 255.255.255.255 Any 1 1 1 1 1 1 1 1 Prev Next Save Cancel 65535 65535 65535 65535 65535 65535 65535 65535 STEP 6: CONFIGURE WEB ACCESS LOGGING STEP 6: CONFIGURE WEB ACCESS LOGGING Select the method for filtering. Web Access Logging:
Enable or disable Web Access logging. You may view the web access log from the Status > Logs section of the web configuration utility. Web Access Logging : Disabled Enabled Prev Next Save Cancel Click Save to finish. D-Link DIR-815 User Manual 91 Section 3 - Configuration Website Filter Click Website Filter on the navigation menu to configure the Website Filter. The Website Filter function allows you to control access to specific websites. When you are satisfied with your configuration, click Save Settings. 40 -- WEBSITE FILTERING RULES Configure Website Filter below:
Select the function of the Website Filter, the options are ALLOW computers access to ONLY these sites or DENY computers access to ONLY these sites. Clear the list below... Website URL/
Domain:
Click this button to clear the website filter. Enter website URL/Domains in each box. Click the Save Settings button when you are finished. DIR-815 ADVANCED WEBSITE FILTER WEBSITE FILTER WEBSITE FILTER The Website Filter option allows you to set up a list of Web sites you would like to allow or deny through your network. Save Settings Dont Save Settings 40 -- WEBSITE FILTERING RULES Configure Website Filter below:
ALLOW computers access to ONLY these sites DENY computers access to ONLY these sites Clear the list below... Website URL/Domain Save Settings Dont Save Settings D-Link DIR-815 User Manual 92 Section 3 - Configuration Firewall Settings Click Firewall Settings on the navigation menu to configure the Firewall Settings. When you are satisfied with your configuration, click Save Settings. FIREWALL SETTINGS Enable SPI: Enable or disable the Stateful Packet Inspection (SPI) firewall. Disabling the firewall is not recommended. DIR-815 ADVANCED FIREWALL SETTINGS FIREWALL & DMZ SETTINGS FIREWALL & DMZ SETTINGS DMZ means "Demilitarized Zone". DMZ allows computers behind the router firewall to be accessible to Internet traffic.Typically, your DMZ would contain Web servers, FTP servers and others.b ANTI-SPOOF CHECKING Enable or disable anti-spoof checking. Enable anti-spoof checking:
DMZ HOST This option allows you to manually configure the routers demilitarized zone (DMZ). The DMZ should only be used as a last resort when you are having difficulty using other port forwarding tools since the device using this IP address is not protected by the firewall. If you use DMZ, take measures such as client-based virus protection to protect the remaining client PCs on your LAN from possible attacks through DMZd device. Enable DMZ: Check the box to enable the DMZ function. DMZ Host IP Address:
Enter the IP address of the machine that you wish to place in the DMZ. If the machine receives an IP address from the DHCP server, you should create a static DHCP reservation to ensure that the machine always receives the same address from the DHCP server. Use the Computer Name dropdown menu and the << button to quickly select a device. The IP address is automatically populated. Save Settings Dont Save Settings FIREWALL SETTINGS ANTI-SPOOF CHECKING Enable SPI :
Enable anti-spoof checking :
DMZ HOST The DMZ (Demilitarized Zone) option lets you set a single computer on your network outside of the router.If you have a computer that cannot run Internet applications successfully from behind the router, then you can place the computer into the DMZ for unrestricted Internet access. Note:Putting a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. Enable DMZ :
DMZ IP Address :
<<
Computer Name APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION PPTP :
IPSec (VPN) :
RTSP :
SIP :
Save Settings Dont Save Settings D-Link DIR-815 User Manual 93 Section 3 - Configuration Firewall Settings (continued) APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION PPTP: Allows multiple machines on the LAN to connect to their corporate network using the Point-to-Point Tunneling protocol (PPTP) based VPNs. IPSec (VPN): Allows VPN clients to connect to their corporate IPSec-based network. Some VPN clients support traversal of IPSec through NAT. This Application Level Gateway (ALG) may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG off. Please check with the system administrator of your corporate network whether your VPN client supports NAT traversal. RTSP: A llows applications that use Real Time Streaming Protocol (RTSP)to receive streaming media from the Internet. DIR-815 ADVANCED FIREWALL SETTINGS FIREWALL & DMZ SETTINGS FIREWALL & DMZ SETTINGS DMZ means "Demilitarized Zone". DMZ allows computers behind the router firewall to be accessible to Internet traffic.Typically, your DMZ would contain Web servers, FTP servers and others.b Save Settings Dont Save Settings FIREWALL SETTINGS ANTI-SPOOF CHECKING Enable SPI :
Enable anti-spoof checking :
DMZ HOST The DMZ (Demilitarized Zone) option lets you set a single computer on your network outside of the router.If you have a computer that cannot run Internet applications successfully from behind the router, then you can place the computer into the DMZ for unrestricted Internet access. Note:Putting a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort. Enable DMZ :
DMZ IP Address :
<<
Computer Name SIP: Enabling Session Initiation Protocol (SIP) allows devices and applications using VoIP (Voice over IP). Some VoIP applications and devices have the ability to discover NAT devices and work around them. This ALG may interfere with the operation of such devices. If you are having trouble making VoIP calls, try turning this ALG off. APPLICATION LEVEL GATEWAY (ALG) CONFIGURATION PPTP :
IPSec (VPN) :
RTSP :
SIP :
Save Settings Dont Save Settings Click the Save Settings button when you are finished. D-Link DIR-815 User Manual 94 Section 3 - Configuration Click Routing on the navigation menu to configure Routing. The routing page allows you to define custom static routes to control the route which your data takes. When you are satisfied with your configuration, click Save Settings. Routing 32 -- ROUTE LIST Enable: Check the box to enable this rule. Name: Enter a name for this static route. Destination IP: Enter the destination IP address. Gateway: Enter the gateway IP address. Metric: Enter the metric value between 1-255. Interface: Select the Interface from the drop-down menu. Click the Save Settings button when you are finished. DIR-815 ROUTING ROUTING ADVANCED ROUTING The Routing option allows you to define static routes to specific destinations. Save Settings Dont Save Settings 24 -- APPLICATION RULES Remaining number of rules that can be created: 24 Name Destination IP Netmask Gateway Save Settings Dont Save Settings Metric Interface 1 WAN(172.17.5.x) D-Link DIR-815 User Manual 95 Section 3 - Configuration Advanced Wireless Click Advanced Wireless on the navigation menu to configure the advanced wireless options. When you are satisfied with your configuration, click Save Settings. ADVANCED WIRELESS SETTINGS Wireless Band: 2.4 GHz Band Transmit Power: Select the desired wireless transmission power. DIR-815 ADVANCED ADVANCED WIRELESS ADVANCED WIRELESS SETTINGS ADVANCED WIRELESS SETTINGS These options are for users that wish to change the behavior of their 802.11n wireless radio from the standard settings. We do not recommend changing these settings from the factory defaults. Incorrect settings may impact the performance of your wireless radio. The default settings should provide the best wireless radio performance in most environments. WLAN Partition: Check this box to enable user isolation. User isolation forces wireless clients to communicate with each other through the access point. WMM Enable: Enable or Disable Wi-Fi MultiMedia QoS. HT 20/40 Coexistence:
Enable or disable HT20/40 Coexistence. ADVANCED WIRELESS SETTINGS Wireless Band: 5 GHz Band Transmit Power: Select the desired wireless transmission power. WLAN Partition: Check this box to enable user isolation. User isolation forces wireless clients to communicate with each other through the access point. WMM Enable: Enable or Disable Wi-Fi MultiMedia QoS. Click the Save Settings button when you are finished. Save Settings Dont Save Settings ADVANCED WIRELESS SETTINGS Wireless Band : 2.4GHz Band High Transmit Power :
WLAN Partition :
WMM Enable :
HT 20/40 Coexistence : Enable Disable ADVANCED WIRELESS SETTINGS Wireless Band : 5GHz Band High Transmit Power :
WLAN Partition :
WMM Enable :
Save Settings Dont Save Settings D-Link DIR-815 User Manual 96 Section 3 - Configuration Wi-Fi Protected Setup Click Wi-Fi Protected Setup on the navigation menu to configure the Wi-Fi Protected Setup
(WPS) feature. Refer to WPS Button on page 134 for more information about WPS. When you are satisfied with your configuration, click Save Settings. DIR-815 ADVANCED WI-FI PROTECTED SETUP WI-FI PROTECTED SETUP WI-FI PROTECTED SETUP Wi-Fi Protected Setup is used to easily add devices to a network using a PIN or button press. Devices must support Wi-Fi Protected Setup in order to be configured by this method. If the PIN changes, the new PIN will be used in following Wi-Fi Protected Setup process. Clicking on ''Don't Save Settings'' button will not reset the PIN. However, if the new PIN is not saved, it will get lost when the device reboots or loses power. Save Settings Dont Save Settings WI-FI PROTECTED SETUP Enable :
WiFi Protected Setup : Enabled/Configured Lock WPS-PIN Setup :
PIN SETTINGS ADD WIRELESS STATION Save Settings Dont Save Settings PIN : 49445183 Reset PIN to Default Generate New Pin Connect your Wireless Device WI-FI PROTECTED SETUP Enable: Check the box to enable WPS. WiFi Protected Setup:
Lock WPS-PIN Setup:
The current status of the WPS feature is displayed here. Enable or disable WPS-PIN functionality. PIN SETTINGS PIN: The currently defined WPS-PIN is displyaed here. Reset PIN to Default Click this button to reset the WPS-PIN to the factory default. Generate New PIN Click this button to generate a new WPS PIN. ADD WIRELESS STATION Connect your Wireless Device:
Click this button to launch the WPS Add Device Wizard. Refer to Add Wireless Device with WPS on page 47 for more information. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual 97 Section 3 - Configuration Advanced Network Click Advanced Network on the navigation menu to configure the Advanced Wireless settings. This page allows for the configuration of miscillaneous settings. When you are satisfied with your configuration, click Save Settings. Enable UPnP IGD: Click Enable to use the UPnP feature. UPnP provides compatibility with networking equipment, software, and peripherals. UPNP Enable WAN Ping Response:
Enable or disable the router to reply to pings. WAN PING WAN PORT SPEED WAN Port Speed: You may set the port speed of the Internet port to 10 Mbps, 100 Mbps, or Auto 10/100 Mbps. Using Auto 10/100 Mbps is recommended. MULTICAST STREAMS Enable Multicast Streams:
Enable to allow IPv4 multicast traffic to pass through the router from the Internet. IPV6 MULTICAST STREAMS Enable IPv6 Multicast Streams:
Enable to allow IPv6 multicast traffic to pass through the router from the Internet. Click the Save Settings button when you are finished. DIR-815 ADVANCED ADVANCED NETWORK ADVANCED NETWORK SETTINGS ADVANCED NETWORK SETTINGS These options are for users that wish to change the LAN settings. We do not recommend changing these settings from factory default. Changing these settings may affect the behavior of your network. Save Settings Dont Save Settings UPNP Universal Plug and Play(UPnP) supports peer-to-peer Plug and Play functionality for network devices. Enable UPnP IGD :
WAN PING If you enable this feature, the WAN port of your router will respond to ping requests from the Internet that are sent to the WAN IP Address. Enable WAN Ping Response :
WAN PORT SPEED MULTICAST STREAMS WAN Port Speed :
Auto 10/100Mbps Enable Multicast Streams :
IPV6 MULTICAST STREAMS Enable IPv6 Multicast Streams :
Save Settings Dont Save Settings D-Link DIR-815 User Manual 98 Section 3 - Configuration Guest Zone Click Guest Zone on the navigation menu to configure Guest Zones. The guest zone feature allows you to create wireless networks for visitors. This allows you to keep your devices secure. When you are satisfied with your configuration, click Save Settings. GUEST ZONE Enable Routing Between Zones:
If a guest zone or zones are enabled and this option is disabled, guest device network connectivity is restricted to the Internet. If this option is enabled, guest devices are allowed access to other local network devices. DIR-815 GUEST ZONE GUEST ZONE ADVANCED GUEST ZONE Use this section to configure the guest zone settings of your router. The guest zone provide a separate network zone for guest to access Internet. Save Settings Dont Save Settings GUEST ZONE SESSION 2.4GHZ Enable Routing Between Zones :
SESSION 2.4GHZ / SESSION 5GHZ Enable Guest Zone: Enable or disable this guest wireless network. From the drop down menu you may apply a schedule to enable or disable this wireless network. Click New Schedule to create a new schedule. Refer to Schedules on page 113 for more information. SESSION 5GHZ Enable Guest Zone : Always Wireless Band : 2.4GHz Band New Schedule Wireless Network Name :
(Also called the SSID) Security Mode :
None Enable Guest Zone : Always Wireless Band : 5GHz Band New Schedule Wireless Network Name :
(Also called the SSID) Security Mode :
None Save Settings Dont Save Settings Wireless Band: The current wireless band is displayed here, either 2.4GHz or 5GHz. Wireless Network Name:
Create a name for your wireless network. Security Mode: Select a wireless security encryption option. The options are None, WEP, WPA-Personal, and WPA-Enterprise. Using WPA is recommended. Refer to Wireless Security Mode on page 52 for more information. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual 99 Section 3 - Configuration IPv6 Firewall Click IPv6 Firewall on the navigation menu to configure the IPv6 Firewall Settings. When you are satisfied with your configuration, click Save Settings. Enable IPv6 Simple Security:
IPV6 SIMPLE SECURITY Enable or disable the IPv6 firewall. 20 -- IPV6 FIREWALL RULES Configure IPv6 Filtering below:
Select the function of the IPv6 Filter, the options are Turn IPv6 Filtering OFF, Turn IPv6 Filtering ON and ALLOW rules listed, Turn IPv6 Filtering ON and DENY rules listed. Enable: Check the box to enable this rule. Name: Enter a name for the rule. Schedule: Select the schedule from the drop-down menu. The default is Always. Refer to Schedules on page 113 for more information on creating new schedules. Source Interface: Select the source interface, WAN or LAN, from the drop down menu. Source IP Address /
PrefixLength:
Enter the source IP address and specify the prefix length for the rule. Protocol: Select the protocol to apply the rule to, either ALL, TCP, UDP, or ICMP. Destination Interface:
Select the destination interface, WAN or LAN, from the drop down menu. DIR-815 ADVANCED IPV6 FIREWALL IPV6 FIREWALL IPV6 FIREWALL The firewall settings section is an advance feature used to allow or deny traffic from passing through the device. It works in the same way as IP Filters with additional settings. You can create more detailed rules for the device. Save Settings Dont Save Settings IPV6 SIMPLE SECURITY Enable IPv6 Simple Security :
20 -- IPV6 FIREWALL RULES Remaining number of rules that can be created: 24 Configure IPv6 Filtering below:
Turn IPv6 Filtering OFF Turn IPv6 Filtering ON and ALLOW rules listed Turn IPv6 Filtering ON and DENY rules listed Name Source Interface LAN Dest Interface LAN Schedule Always IP Address /PrefixLength IP Address /PrefixLength Protocol ALL Port Range
~
Save Settings Dont Save Settings D-Link DIR-815 User Manual 100 Section 3 - Configuration IPv6 Firewall (continued) Destination IP Address /
PrefixLength:
Enter the destination IP address and specify the prefix length for the rule. Port Range: Enter the port range to apply the rule to. If the protocol is set as ALL or ICMP this feature is disabled. Click the Save Settings button when you are finished. DIR-815 ADVANCED IPV6 FIREWALL IPV6 FIREWALL IPV6 FIREWALL The firewall settings section is an advance feature used to allow or deny traffic from passing through the device. It works in the same way as IP Filters with additional settings. You can create more detailed rules for the device. Save Settings Dont Save Settings IPV6 SIMPLE SECURITY Enable IPv6 Simple Security :
20 -- IPV6 FIREWALL RULES Remaining number of rules that can be created: 24 Configure IPv6 Filtering below:
Turn IPv6 Filtering OFF Turn IPv6 Filtering ON and ALLOW rules listed Turn IPv6 Filtering ON and DENY rules listed Name Source Interface LAN Dest Interface LAN Schedule Always IP Address /PrefixLength IP Address /PrefixLength Protocol LAN Port Range
~
Save Settings Dont Save Settings D-Link DIR-815 User Manual 101 Section 3 - Configuration Click IPv6 Routing on the navigation menu to configure IPv6 Routing. The routing page allows you to define custom static routes to control the route which your data takes. When you are satisfied with your configuration, click Save Settings. IPv6 Routing 10 -- ROUTE LIST Enable: Check the box to enable this rule. Name: Enter a name for this IPv6 static route. Destination IPv6 /
Prefix Length:
Enter the destination IPv6 address and Prefix Length. Metric: Enter the metric value between 1-255. Interface: Select the Interface from the drop-down menu. Gateway: Enter the gateway IPv6 address. Click the Save Settings button when you are finished. DIR-815 ADVANCED IPV6 ROUTING ROUTING ROUTING This Routing page allows you to specify custom routes that determine how data is moved around your network. Save Settings Dont Save Settings 10 -- ROUTE LIST Name Destination IPv6 / Prefix Length
/
Metric 256 Interface NULL Gateway Save Settings Dont Save Settings D-Link DIR-815 User Manual 102 Section 3 - Configuration The Tools tab provides access to administration related settings of your DIR-815. Tools SETUP ADVANCED TOOLS STATUS SUPPORT DIR-815 ADMIN TIME SYSLOG EMAIL SETTINGS SYSTEM FIRMWARE DYNAMIC DNS SYSTEM CHECK SCHEDULES To return to this Web UI Table of Contents page, simply click the D-Link logo on the top right of each page. DIR-815 INTERNET SETUP INTERNET CONNECTION D-Link DIR-815 User Manual 103 Section 3 - ConfigurationSave SettingsDont Save SettingsADMINISTRATOR SETTINGSThe 'admin' account can access the management interface. The admin has read/write access and can change password. By default there is no password configured. It is highly recommended that you create a password to keep your router secure. Save SettingsDont Save SettingsADMIN PASSWORDPlease enter the same password into both boxes, for confirmation.Password :Verify Password :ADMINISTRATIONEnable HTTPS Server :Enable Remote Management :Remote Admin Port :8080Use HTTPS:Remote Admin Inbound Filter :Allow AllDetails :Allow All Admin Click Admin on the navigation menu to configure the administration settings. This page allows you to configure access to the web configuration utility. When you are satisfied with your configuration, click Save Settings. ADMIN PASSWORD Password: Enter the new password for the admin account. Verify Password: Enter the new password for the admin account one more time. ADMINISTRATION Enable HTTPS Server::
Check to enable HTTPS to connect to the router securely. You may access the web configuration utility using https://dlinkrouter.local./. ADMINISTRATION Enable Remote Management:
Remote management allows the DIR-815 to be configured from the Internet by a web browser. A password is still required to access the web management interface. Remote Admin Port:
Enter the port number you wish to use to access the DIR-815s web configuration utility. Example: http://x.x.x.x:8080 where x.x.x.x is the Internet IP address of the DIR-815 and 8080 is the port used for the web management interface. Note: If you enabled HTTPS Server and wish to access the router remotely and securely, you may enter https:// at the beginning of the address. Remote Admin Inbound Filter:
You may select an inbound filter from the drop down menu to restrict remote administration. Refer to Inbound Filter on page 87 for more information. Details: The current status of the Remote Administration Inbound filter is displayed here. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual DIR-815 ADMIN ADMINISTRATOR SETTINGS TOOLS ADMINISTRATOR SETTINGS The 'admin' account can access the management interface. The admin has read/write access and can change password. By default there is no password configured. It is highly recommended that you create a password to keep your router secure. Save Settings Dont Save Settings ADMIN PASSWORD Please enter the same password into both boxes, for confirmation. Password :
Verify Password :
Enable HTTPS Server :
Enable Remote Management :
Remote Admin Port :
8080 Use HTTPS:
Remote Admin Inbound Filter :
Allow All Details :
Allow All Save Settings Dont Save Settings 104 Section 3 - Configuration Time Click Time on the navigation menu to configure the time. When you are satisfied with your configuration, click Save Settings. TIME AND DATE CONFIGURATION Time: The currently set time on the router is displayed. Time Zone: Displays the current date and time of the router. Enable Daylight Saving:
Daylight Saving Offset:
Daylight Saving Dates:
Enable or disable daylight saving time. Select the daylight saving offset if Daylight Saving time will be used. Select the date range for when to start and stop daylight savings time. AUTOMATIC TIME AND DATE CONFIGURATION Automatically synchronize with D-Links Internet time server:
Enable this option to get the current time from an NTP server on the Internet. To configure the router's time and date manually, disable this option and use the drop-down menus that appear to input the time and date. NTP Server Used: If you enable this option, select an NTP server from the drop-down menu. SET THE TIME AND DATE MANUALLY You may manually set the time from this option or set the time by clicking Sync. your computers time settings. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual DIR-815 TIME TIME AND DATE TOOLS TIME AND DATE The Time and Date Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone you are in and set the NTP (Network Time Protocol) Server. Daylight Saving can also be configured to adjust the time when needed. Save Settings Dont Save Settings TIME AND DATE CONFIGURATION Time : 2016-09-19 12:00:00 Time Zone :
(GMT+08:00) Taipei Enable Daylight Saving :
Daylight Saving Offset :
-02:00 Daylight Saving Dates :
Month Week Day of Week Time DST Start DST End Mar Nov 2nd 1st Sun Sun 2 am 2 am AUTOMATIC TIME AND DATE CONFIGURATION Automatically synchronize with D-Links Internet time server NTP Server Used :
ntp1.dlink.com SET THE TIME AND DATE MANUALLY Year 2016 Hour 4 Month Sep Minute 6 Day Second 19 59 Sync. your computers time settings Save Settings Dont Save Settings 105 Section 3 - Configuration Syslog Click Syslog on the navigation menu to configure the system log settings. This device maintains a running log of events which can be sent to a syslog server or emailed. Refer to Logs on page 117 for an example system log. When you are satisfied with your configuration, click Save Settings. SYSLOG SETTINGS Enable or disable the sending of router logs to a syslog server. Enable Logging to SysLog Server:
If you enable Logging to SysLog Server, enter the Syslog Server IP Address:
SysLog Server IP Address:
Enter the IP address of the syslog server. Use the Computer Name dropdown menu and the << button to quickly select a device. The IP address is automatically populated. Click the Save Settings button when you are finished. DIR-815 SYSLOG SYSLOG TOOLS SYSLOG The SysLog options allow you to send log information to a Syslog Server. Save Settings Dont Save Settings SYSLOG SETTINGS Enable Logging To SysLog Server:
Syslog Server IP Address:
Save Settings Dont Save Settings
<<
Computer Name D-Link DIR-815 User Manual 106 Section 3 - Configuration Email Settings Click Email Settings on the navigation menu to configure the email account settings used for the system log. When you are satisfied with your configuration, click Save Settings. EMAIL NOTIFICATION Enable Email Notification:
When this option is enabled, router activity logs are emailed to a designated email address. DIR-815 TOOLS EMAIL SETTINGS EMAIL SETTINGS EMAIL SETTINGS The Email feature can be used to send the system log files and router alert messages to your email address. If you enabled Email Notification, configure the following settings:
EMAIL SETTINGS From Email Address:
This email address will appear as the sender when you receive a log file or firmware upgrade notification via email. To Email Address: Enter the email address where you want the email sent. Email Subject: Enter the subject line of the email. SMTP Server Address:
Enter the SMTP server address for sending email. SMTP Server Port: Enter the SMTP port used on the server. Save Settings Dont Save Settings EMAIL NOTIFICATION EMAIL SETTINGS Enable Email Notification :
From Email Address :
To Email Address :
Email Subject :
SMTP Server Address :
SMTP Server Port :
Enable Authentication :
Account Name :
Password :
Verify Password :
EMAIL LOG WHEN FULL OR ON SCHEDULE On Log Full :
On Schedule :
Schedule :
Never Detail :
Never Send Mail Now Enable Authentication:
Check this box if your SMTP server requires authentication. Save Settings Dont Save Settings If you enabled Authentication, configure the following settings:
Account Name: Enter your account for sending email. Password: Enter the password associated with the account. Verify Password: Re-type the password associated with the account. Send Mail Now: Click this button to send a test email using the above settings. D-Link DIR-815 User Manual 107 Section 3 - Configuration Email Settings (continued) EMAIL LOG WHEN FULL OR ON SCHEDULE On Log Full: When this option is selected, logs will be sent via email to your account when the log is full. On Schedule: Selecting this option will send the logs via email according to schedule. Schedule: Select a schedule for the emailing of system logs. From the drop down menu you may apply a schedule to enable or disable this wireless network. Click New Schedule to create a new schedule. Refer to Schedules on page 113 for more information. Detail: The currently selected schedule is listed here. Click the Save Settings button when you are finished. DIR-815 TOOLS EMAIL SETTINGS EMAIL SETTINGS EMAIL SETTINGS The Email feature can be used to send the system log files and router alert messages to your email address. Save Settings Dont Save Settings EMAIL NOTIFICATION EMAIL SETTINGS Enable Email Notification :
From Email Address :
To Email Address :
Email Subject :
SMTP Server Address :
SMTP Server Port :
Enable Authentication :
Account Name :
Password :
Verify Password :
EMAIL LOG WHEN FULL OR ON SCHEDULE On Log Full :
On Schedule :
Schedule :
Never Detail :
Never Save Settings Dont Save Settings Send Mail Now D-Link DIR-815 User Manual 108 Section 3 - Configuration System Click System on the navigation menu to configure the system settings. This section allows you to manage the routers configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that youve created. SAVE AND RESTORE SETTINGS Save Settings To Local Hard Drive:
Use this option to save the current router configuration settings to a file on the hard disk of the computer you are using. Click the Save Configuration button. A file dialog will appear, allowing you to select a location and file name for the settings. Load Settings From Local Hard Drive:
Use this option to load previously saved router configuration settings. Use the Choose File option to find a previously saved file of configuration settings and then click the Restore Configuration From File to transfer those settings to the router. Restore To Factory Default Settings:
This option will restore all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you want to save the current router configuration settings, use the Save button above. Reboot The Device: Click this button to reboot the device. Clear Language Pack:
If the device is of other language than English, clicking this button to convert the routers language back to English. DIR-815 SYSTEM SAVE AND RESTORE SETTINGS TOOLS SAVE AND RESTORE SETTINGS Once the router is configured you can save the configuration settings to a configuration file on your hard drive. You also have the option to load configuration settings, or restore the factory default settings. SAVE AND RESTORE SETTINGS Save Settings To Local Hard Drive :
Save Configuration Load Settings From Local Hard Drive :
Choose File No file chosen Restore Configuration From File Restore To Factory Default Settings :
Restore Factory Defaults Reboot The Device :
Reboot the Device Clear Language Pack :
Clear D-Link DIR-815 User Manual 109 Section 3 - Configuration Firmware Click Firmware on the navigation menu to configure the firmware. Please check the D-Link support website for firmware updates and new language packs at http://support.dlink.com. Be sure to keep your router firmware updated to help protect against the latest cyber threats. Current Firmware Version:
Current Firmware Time:
Check Online Now for Latest Firmware Version:
FIRMWARE INFORMATION The current firmware version is displayed here. The release date and time of the current firmware is displayed here. Click this button to prompt the router to check for a new firmware version. DIR-815 FIRMWARE FIRMWARE UPDATE TOOLS FIRMWARE UPDATE There may be new firmware for your router to improve functionality and performance. Click here to check for an upgrade on our support site. To upgrade the firmware, locate the upgrade file on the local hard drive with the Browse button. Once you have found the file to be used, click the Upload button to start the firmware upgrade. The language pack allows you to change the language of the user interface on the router. We suggest that you upgrade your current language pack if you upgrade the firmware. This ensures that any changes in the firmware are displayed correctly. To upgrade the language pack, locate the upgrade file on the local hard drive with the Browse button. Once you have found the file to be used, click the Upload button to start the language pack upgrade. SAVE AND RESTORE SETTINGS Current Firmware Version : V4.00 Current Firmware Time : Jul-21-2016 11:02:40 Check Online Now for Latest Firmware Version :
Check Now FIRMWARE UPGRADE Note: Some firmware upgrades reset the configuration options to the factory defaults. Before performing an upgrade, be sure to save the current configuration. To upgrade the firmware, your PC must have a wired connection to the router. Enter the name of the firmware upgrade file, and click on the Upload button. FIRMWARE UPGRADE Upload: Select a file to upgrade your device with by clicking the Choose File button. Click the Upload button to begin the firmware upgrade. LANGUAGE PACK UPGRADE Clear Config: Check this box to clear the current settings of your DIR-815 once the firmware update is applied. Upload :
Choose File No file chosen Clear Config :
Upload :
Choose File No file chosen Upload Upload LANGUAGE PACK UPGRADE Upload: You can change the language of the web UI by uploading language packs. Select a file to upgrade your device with by clicking the Choose File button. Click the Upload button to begin the firmware upgrade. Click the Save Settings button when you are finished. D-Link DIR-815 User Manual 110 Section 3 - Configuration Click Dynamic DNS on the navigation menu to configure the Dynamic Domain Name Server
(DDNS) client. DDNS makes accessing your network from the Internet easier by providing you with an easy to use web address. Owners of D-Link routers can use the dlinkdns service. Dynamic DNS DYNAMIC DNS SETTINGS Enable or disable the Dynamic DNS feature. Enable Dynamic DNS:
If you enabled Dynamic DNS, configure the following settings:
Server Address: Enter the IP address of your DDNS provider. Use the Select Dynamic DNS Server dropdown menu and the << button to quickly select a device. The IP address is automatically populated. Host Name: Enter the host name that you registered with your DDNS service provider. Username: Enter your DDNS username. Password: Enter your DDNS password. Verify Password: Enter your DDNS password one more time. Timeout: Enter a timeout time (in hours) before the DDNS information is automatically updated. Status: The current status of your DDNS service is displayed here. Click the Save Settings button when you are finished. DIR-815 TOOLS DYNAMIC DNS DYNAMIC DNS DYNAMIC DNS The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc...) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter your host name to connect to your game server no matter what your IP address is. Save Settings Dont Save Settings DYNAMIC DNS SETTINGS Enable Dynamic DNS :
Server Address :
Host Name :
Username :
Password :
Verify Password :
<<
Select Dynamic DNS Server Timeout :
576
(Times) Status : Disconnected Save Settings Dont Save Settings D-Link DIR-815 User Manual 111 Section 3 - Configuration System Check Click System Check on the navigation menu to test your connection to the Internet. Host Name or IP Address:
Enter either an IP address or web address that you wish to Ping and click Ping. PING TEST Host Name or IPv6 Address:
Enter either an IPv6 address or web address that you wish to Ping and click Ping. IPV6 PING TEST PING RESULT The results of the test are displayed in this dialog box. DIR-815 TOOLS SYSTEM CHECK PING TEST PING TEST Ping Test sends "ping" packets to test a computer on the Internet. PING TEST IPV6 PING TEST PING RESULT Result here Host Name or IP Address :
Host Name or IPv6 Address :
Ping Ping D-Link DIR-815 User Manual 112 Section 3 - Configuration Schedules Click Schedules on the navigation menu to configure the system schedules. Several router functions be operated according to a pre-configured schedule which may be created from this page. 10 -- ADD SCHEDULE RULE If you wish to create a new schedule, fill in the following fields:
Name: Enter a name for your new schedule. Day(s): Choose to have the schedule apply to All Week or Select Days and check the boxes of the days to apply the rules to. All Day - 24 hrs: Check this box to have the rule apply all day or leave this box unchecked at fill in the Start Time and End Time fields. Start Time: Enter the start time for this rule to start. End Time: Enter the end time for this rule to stop. Click the Add button when you are satisfied with your new schedule. SCHEDULE RULES LIST The currently added rules are displayed in this table. You may edit or delete a rule by clicking on its corresponding Edit or Delete buttons. DIR-815 SCHEDULES SCHEDULES TOOLS SCHEDULES The Schedule configuration option is used to manage schedule rules for "WAN", "Wireless", "Virtual Server", "Port Forwarding",
"Applications" and "Network Filter". 10 -- ADD SCHEDULE RULE Name :
Day(s) : All Week Select Days Sun Mon Tue Wed Thu Frid Sat All Day - 24 hrs :
Start Time :
End Time :
:
:
(hour:minute)
(hour:minute) Add Cancel SCHEDULE RULES LIST Name Days Time Frame D-Link DIR-815 User Manual 113 Section 3 - Configuration The Status tab provides information about the DIR-815s current status. Status SETUP ADVANCED TOOLS STATUS SUPPORT DIR-815 DEVICE INFO LOGS STATISTICS INTERNET SESSIONS WIRELESS ROUTING IPV6 IPV6 ROUTING To return to this Web UI Table of Contents page, simply click the D-Link logo on the top right of each page. DIR-815 INTERNET SETUP INTERNET CONNECTION D-Link DIR-815 User Manual 114 Section 3 - ConfigurationDEVICE INFORMATIONAll of your Internet and network connection details are displayed on this page. The firmware version is also displayed here.WANConnection Type :DHCP ClientCable Status :ConnectedNetwork Status :ConnectedRenewReleaseConnection Up Time :0 Day 0 Hour 0 Min 0 SecMAC Address :ff:ff:ff:ff:ff:ffIP Address :192.168.0.1GENERALTime:2016-09-19 13:00Current Firmware Version :V4.00 Device Info Click Device Info to see current information about the DIR-815. This pages displays LAN, WAN (Internet), and Wireless information. The DIR-815s currently set time and firmware are displayed here. GENERAL DIR-815 DEVICE INFO DEVICE INFORMATION STATUS DEVICE INFORMATION All of your Internet and network connection details are displayed on this page. The firmware version is also displayed here. The DIR-815s currently configured Internet connection settings are displayed here. WAN GENERAL WAN The DIR-815s currently configured local network settings are displayed here. LAN The DIR-815s currently configured 2.4 GHz wireless network settings are displayed here. LAN WIRELESS LAN Time: 2016-09-19 13:00 Current Firmware Version : V4.00 Connection Type : DHCP Client Cable Status : Connected Network Status : Connected Renew Release Connection Up Time : 0 Day 0 Hour 0 Min 0 Sec MAC Address :
ff:ff:ff:ff:ff:ff IP Address : 192.168.0.1 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1 Primary DNS Server : 192.168.0.1 Secondary DNS Server : 192.168.0.1 MAC Address :
ff:ff:ff:ff:ff:ff IP Address : 192.168.0.1 Subnet Mask 255.255.255.0 DHCP Server : Enabled WIRELESS LAN Wireless Radio : Enabled MAC Address :
ff:ff:ff:ff:ff:ff 802.11 Mode : Mixed 802.11n, 802.11g and 802.11b Channel Width : 20/40MHz Channel : 1 Network Name (SSID) : Your_2.4GHz_Network Wi-Fi Protected Setup : Enabled/Not configured Security : NONE Guest Zone Wireless Radio : Disabled Guest Zone Network Name (SSID) :
Guest Zone Security : NONE D-Link DIR-815 User Manual 115 Section 3 - Configuration Device Info (continued) The DIR-815s currently configured 5 GHz wireless network settings are displayed here. WIRELESS LAN2 WIRELESS LAN2 The devices currently connected to the DIR-815s are displayed here. LAN COMPUTERS The DIR-815s current IGMP multicast information is displayed here. IGMP MULTICAST MEMBERSHIPS Wireless Radio : Enabled MAC Address :
ff:ff:ff:ff:ff:ff 802.11 Mode : Mixed 802.11ac, 802.11n and 802.11a Channel Width : 20/40/80MHz Channel : 161 Network Name (SSID) : Your_5GHz_Network Wi-Fi Protected Setup : Enabled/Not configured Security : NONE Guest Zone Wireless Radio : Disabled Guest Zone Network Name (SSID) :
Guest Zone Security : NONE IP Address Name(if any) LAN COMPUTERS MAC Address ff:ff:ff:ff:ff:ff IGMP MULTICAST MEMBERSHIPS IPv4 Multicast Group Address IPv6 Multicast Group Address D-Link DIR-815 User Manual 116 Section 3 - Configuration Logs Click Logs on the navigation menu to view the system log. This device maintains a running log of events which can be sent to a syslog server or emailed. Refer to Syslog on page 106 for more information on configuring the system log. Click the Save button to save the log file to your local hard drive. SAVE LOG FILE WAN Log Type: To change the type of information to view and then click the Save Settings button. Log Level: To change the levl of information to view and then click the Save Settings button. LOG FILES Click the navigation buttons to view the log file. Click Link To Email Log Settings to be redirected to the Email Log Settings page. Refer Email Settings on page 107 for more information. STATUS VIEW LOG DIR-815 LOGS VIEW LOG The View Log displays the activities occurring on the router. Save Settings Dont Save Settings SAVE LOG FILE WAN LOG FILES Save Log File To Local Hard Drive. Save Log Type : System Log Level : Critical Firewall & Security Router Status Warning Information First Page Last Page Previous Next Clear Link To Email Log Settings 1/1 Time Message Sep 19 09:15:05 2016 User Admin login success D-Link DIR-815 User Manual 117 Section 3 - Configuration Click Statistics on the navigation menu to view statistics on the amount of traffic which has passed through the DIR-815s interfaces. Click the Refresh Statistics button to view the latest numbers. Statistics DIR-815 STATISTICS TRAFFIC STATISTICS STATUS TRAFFIC STATISTICS Traffic Statistics displays Receive and Transmit packets passing through the device. Refresh Statistics LAN STATISTICS Sent :
TX Packets Dropped :
Collisions :
WAN STATISTICS Sent :
TX Packets Dropped :
Collisions :
WIRELESS STATISTICS - 2.4GHZ BAND Sent :
TX Packets Dropped :
Collisions :
WIRELESS STATISTICS - 5GHZ BAND Sent :
TX Packets Dropped :
Collisions :
0 0 0 0 0 0 0 0 0 0 0 0 Received :
RX Packets Dropped :
Errors :
Received :
RX Packets Dropped :
Errors :
Received :
RX Packets Dropped :
Errors :
Received :
RX Packets Dropped :
Errors :
0 0 0 0 0 0 0 0 0 0 0 0 D-Link DIR-815 User Manual 118 Section 3 - Configuration Internet Sessions Click Internet Sessions on the navigation menu to view information about currently active Internet connections. This page helps to diagnose connectivity issues. Click the Refresh button to view the latest information. DIR-815 STATUS INTERNET SESSIONS INTERNET SESSIONS INTERNET SESSIONS This page displays Source and Destination sessions passing through the device. Refresh IP 192.168.0.100 Protocol UDP NAT 54674 Internet State 192.168.0.1 Dir Out Time Out 60 D-Link DIR-815 User Manual 119 Section 3 - Configuration Click Wireless on the navigation menu to view information about currently connected wireless clients. You may view each clients MAC address, IP address, 802.11 mode, speed, and signal strength. Wireless DIR-815 WIRELESS STATUS CONNECTED WIRELESS CLIENT LIST CONNECTED WIRELESS CLIENT LISTV View the wireless clients that are connected to the router. (A client might linger in the list for a few minutes after an unexpected disconnect.) NUMBER OF WIRELESS CLIENTS - 2.4GHZ BAND : 0 MAC Address IP Address Mode Rate(Mbps) Signal (%) NUMBER OF WIRELESS CLIENTS - 5GHZ BAND : 0 MAC Address IP Address Mode Rate(Mbps) Signal (%) D-Link DIR-815 User Manual 120 Section 3 - Configuration Click Routing to view the currently configured IPv4 routing table. Routing DIR-815 ROUTING ROUTING STATUS ROUTING Routing Table This page displays the routing details configured for your router. ROUTING TABLE Destination 192.168.0.100 Gateway 0.0.0.0 Genmask Metric 255.255.255.0 0 Iface eth1 Creator 0 D-Link DIR-815 User Manual 121 Section 3 - Configuration IPV6 Click IPv6 to view the currently IPv6 information. IPv6 Connection Type:
IPv6 Default Gateway:
LAN IPv6 Link-Local Address:
IPV6 CONNECTION INFORMATION The currently configured IPv6 connection type is listed here. The current IPv6 default gateway is listed here. The current IPv6 Link-Local address is listed here. The currently connected IPv6 computers are listed in this table. LAN IPV6 COMPUTERS DIR-815 IPV6 STATUS IPV6 NETWORK INFORMATION IPV6 NETWORK INFORMATION All of your IPv6 Internet and network connection details are displayed on this IPV6 CONNECTION INFORMATION IPv6 Connection Type : Link-Lcoal IPv6 Default Gateway : NONE LAN IPv6 Link-Local Address :
ffff::fff:fff:ffff:ffff LAN IPV6 COMPUTERS IPv6 Address Name(if any) D-Link DIR-815 User Manual 122 Section 3 - Configuration Click IPv6 Routing to view the currently configured IPv6 routing table. IPv6 Routing DIR-815 STATUS IPV6 ROUTING IPV6 ROUTING IPV6 ROUTING This page displays IPV6 routing details configured for your router. IPV6 ROUTING TABLE Destination IP Gateway Metric Interface fe800000000000000000000000 000000/64 000000000000000000000000 00000000 256 br0 D-Link DIR-815 User Manual 123 Section 3 - Configuration DIR-815 MENU SETUP ADVANCED TOOLS STATUS Support SETUP ADVANCED TOOLS STATUS SUPPORT IPV6 ROUTING Setup Advanced Tools Status SETUP HELP Internet Wireless Settings Network Settings Storage IPv6 ADVANCED HELP Virtual Server Port Forwarding Application Rules QOS Engine Network Filter Inbound Filter Access Control Website filter Firewall Settings Routing Advanced Wireless Wi-Fi Protected Setup Advanced Network Guest Zone IPv6 Firewall IPv6 Routing D-Link DIR-815 User Manual 124 Section 3 - Configuration Connect and Share a USB Storage Device After you have successfully installed and configured your D-Link device, you are ready to enjoy the benefits of D-Links USB sharing technology. This allows you to quickly and easily share a USB storage device with multiple computers on your network. The DIR-815 will share a FAT32 or NTFS-formatted USB storage device using the Samba file sharing protocol. Once connected, you can copy, move, delete, and edit files over the network like you would with any ordinary drive attached to your computer. Refer to Storage on page 57 for more information. Connect a USB storage device to the USB Port on the DIR-815. USB Port D-Link DIR-815 User Manual 125 Section 4 - Connect a USB Storage Device Connecting from a Windows-Based PC Step 1 - Click the Start menu and select Computer. D-Link DIR-815 User Manual 126 Section 4 - Connect a USB Storage Device Step 2 - Click Map network drive. D-Link DIR-815 User Manual 127 Section 4 - Connect a USB Storage Device Step 3 - Select the drive letter you wish to map your network drive to. Enter the DIR-815s IP address and the name of the USB volume you wish to share. For example \\192.168.0.1\usb1_1. Check the boxes Reconnect at logon and Connect using different credentials. Click Finish. D-Link DIR-815 User Manual 128 Section 4 - Connect a USB Storage Device Step 4 - Enter root and the password you configured on the Storage page of the web configuration utility and click Ok. root D-Link DIR-815 User Manual 129 Section 4 - Connect a USB Storage Device Congratulations! Your files are now shared. Repeat this process from each Windows PC you wish to share your USB drive with. D-Link DIR-815 User Manual 130 Section 4 - Connect a USB Storage Device Connecting from a Mac Step 1 - While in Finder, click Go menu and select Connect to Server... D-Link DIR-815 User Manual 131 Section 4 - Connect a USB Storage Device Step 2 - Enter the DIR-815s IP address and the name of the USB volume you wish to share. For example smb//192.168.0.1/usb1_1. Click Connect. D-Link DIR-815 User Manual 132 Section 4 - Connect a USB Storage Device Congratulations Your files are now shared. Repeat this process from each Mac you wish to share your USB drive with. D-Link DIR-815 User Manual 133 Section 4 - Connect a USB Storage Device Connect a Wireless Client to Your Router WPS Button The easiest and most secure way to connect your wireless devices to the router is with WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers, and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-815 router. Please refer to your user manual for the wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step 1 - Press the WPS button on the DIR-815 for about 1 second. The wireless LED on the front will start to blink. WPS Button Step 2 - Within 2 minutes, press the WPS button on your wireless device (or launch the software utility and start the WPS process). Step 3 - Allow up to 1 minute for your connection to be configured. Once the WPS LED stops blinking, you will be connected and your wireless connection will be secure with WPA2. D-Link DIR-815 User Manual 134 Section 5 - Connecting to a Wireless Network Windows 10 When connecting to the DIR-815 wirelessly for the first time, you will need to input the wireless network name (SSID) and Wi-
Fi password (security key) of the device you are connecting to. If your product has a Wi-Fi configuration card, you can find the default network name and Wi-Fi password here. Otherwise refer to the product label for the default Wi-Fi network SSID and password, or enter the Wi-Fi credentials set during the product configuration. To join an existing network, locate the wireless network icon in the taskbar, next to the time display and click on it. Wireless Icon Clicking on this icon will display a list of wireless networks which are within range of your computer. Select the desired network by clicking on the SSID. D-Link DIR-815 User Manual 135 Section 5 - Connecting to a Wireless Network To connect to the SSID, click Connect. To automatically connect with the router when your device next detects the SSID, click the Connect Automatically check box. You will then be prompted to enter the Wi-Fi password (network security key) for the wireless network. Enter the password into the box and click Next to connect to the network. Your computer will now automatically connect to this wireless network when it is detected. You can also use Wi-Fi Protected Setup (WPS) to connect to the router. Press the WPS button on your D-Link device and you will be automatically connected. D-Link DIR-815 User Manual 136 Section 5 - Connecting to a Wireless Network Windows 8 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used. To join an existing network, locate the wireless network icon in the taskbar next to the time display. Wireless Icon Clicking on this icon will display a list of wireless networks that are within connecting proximity of your computer. Select the desired network by clicking on the network name. D-Link DIR-815 User Manual 137 Section 5 - Connecting to a Wireless Network You will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next. If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also press the WPS button on your router during this step to enable the WPS function. When you have established a successful connection to a wireless network, the word Connected will appear next to the name of the network to which you are connected to. D-Link DIR-815 User Manual 138 Section 5 - Connecting to a Wireless Network Windows 7 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). 2. The utility will display any available wireless networks in your area. Wireless Icon D-Link DIR-815 User Manual 139 Section 5 - Connecting to a Wireless Network 3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/
IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router. D-Link DIR-815 User Manual 140 Section 5 - Connecting to a Wireless Network WPS The WPS feature of the DIR-815 can be configured using Windows 7. Carry out the following steps to use Windows 7 to configure the WPS feature:
1. Click the Start button and select Computer from the Start menu. 2. Click Network on the left side. D-Link DIR-815 User Manual 141 Section 5 - Connecting to a Wireless Network 3. Double-click the DIR-815. DIR-815 4. Input the WPS PIN number (on the router label) in the Setup > Wireless Setup menu in the Routers Web UI) and click Next. D-Link DIR-815 User Manual 142 Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue. D-Link DIR-815 User Manual 143 Section 5 - Connecting to a Wireless Network 7. The following window appears while the DIR-815 is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the DIR-815 has been set up successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup. D-Link DIR-815 User Manual 144 Section 5 - Connecting to a Wireless Network Windows Vista Windows Vista users may use the built-in wireless utility. If you are using another companys wireless utility, please refer to the user manual of your wireless adapter for help connecting to a wireless network. Most wireless utilities will have a site survey option similar to the Windows Vista utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility. or Right-click on the wireless computer icon in your system tray (lower-right corner next to the time). Select Connect to a network. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. D-Link DIR-815 User Manual 145 Section 5 - Connecting to a Wireless Network WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2. Highlight the Wi-Fi name (SSID) you would like to connect to and click Connect. D-Link DIR-815 User Manual 146 Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router. D-Link DIR-815 User Manual 147 Section 5 - Connecting to a Wireless Network Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-815. Read the following descriptions if you are having problems. The examples below are illustrated in Windows XP. If you have a different operating system, the screenshots on your computer will look similar to these examples. 1. Why cant I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.11.1 for example), you are not connecting to a website, nor do you have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility. Make sure you have an updated Java-enabled web browser. We recommend the following:
Internet Explorer 10 or higher EDGE Browser 20 or higher Firefox 28 or higher Safari 6.0 or higher Chrome 28 or higher Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable, or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on. Disable any Internet security software running on the computer. Software firewalls such as ZoneAlarm, BlackICE, Sygate, Norton Personal Firewall, and Windows XP firewall may block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. D-Link DIR-815 User Manual 148 Section 6 - Troubleshooting Configure your Internet settings:
Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times. Close your web browser (if open) and open it. Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the login page for your web management. If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer. 2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. This process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default IP address is 192.168.11.1. When logging in, leave the password box empty. D-Link DIR-815 User Manual 149 Section 6 - Troubleshooting 3. Why cant I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). To find the proper MTU Size, youll have to do a special ping of the destination youre trying to go to. A destination could be another computer, or a URL. Click on Start and then click Run. Windows 95, 98, and Me users type in command (Windows NT, 2000, XP, Vista, and 7 users type in cmd) and press Enter (or click OK). Once the window opens, youll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472 D-Link DIR-815 User Manual 150 Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network were working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below:
Open your browser, enter the IP address of your router (192.168.11.1) and click OK. Enter your username (admin) and password (blank by default). Click OK to enter the web configuration page for the device. Click on Setup and then click Manual Configure. To change the MTU, enter the number in the MTU field and click Save Settings to save your settings. Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments of ten. D-Link DIR-815 User Manual 151 Section 6 - Troubleshooting Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when, and where you want it. You will be able to enjoy the freedom that wireless networking delivers. A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people work, and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users. Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards. Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to use servers, printers or an Internet connection supplied through the wired LAN. A wireless router is a device used to provide this link. D-Link DIR-815 User Manual 152 Appendix A - Wireless Basics What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work?
Wireless works similarly to how cordless phones work, through radio signals that transmit data from one point A to point B. But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area to be able to connect your computer. There are two different types of wireless networks: Wireless Local Area Network
(WLAN), and Wireless Personal Area Network (WPAN). Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places like manufacturing plants, industrial locations, university and high school campuses, airports, golf courses, and many other outdoor venues. Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. D-Link DIR-815 User Manual 153 Appendix A - Wireless Basics Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesnt use nearly as much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether its for home, office, business, D-Link has a wireless solution for it. Home Uses/Benefits Gives everyone at home broadband access Surf the web, check email, instant message, etc. Gets rid of the cables around the house Simple and easy to use Small Office and Home Office Uses/Benefits Stay on top of everything at home as you would at office Remotely access your office network from home Share Internet connection and printer with multiple computers No need to dedicate office space Where is wireless used?
Wireless technology is expanding everywhere, not just at home or office. People like the freedom of mobility and its becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called hotspots. Using a D-Link USB adapter with your laptop, you can access the hotspot to connect to the Internet from remote locations like:
airports, hotels, coffee shops, libraries, restaurants, and convention centers. D-Link DIR-815 User Manual 154 Appendix A - Wireless Basics Wireless network is easy to setup, but if youre installing it for the first time it could be quite a task not knowing where to start. Thats why weve put together a few setup steps and tips to help you through the process of setting up a wireless network. Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your router or access point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range. Eliminate Interference Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. Security Dont let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to the product manual for detail information on how to set it up. D-Link DIR-815 User Manual 155 Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking:
Infrastructure All wireless clients will connect to an access point or wireless router. Ad-hoc Directly connecting to another computer for peer-to-peer communication using wireless network adapters on each computer, such as two or more wireless network USB adapters. An Infrastructure network contains an access point or wireless router. All the wireless devices, or clients, will connect to the wireless router or access point. An Ad-hoc network contains only clients, such as laptops with wireless USB adapters. All the adapters must be in Ad-hoc mode to communicate. D-Link DIR-815 User Manual 156 Appendix A - Wireless Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows 7/Vista users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters. D-Link DIR-815 User Manual 157 Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1 Windows 7 -
Windows Vista -
Windows XP -
Windows 2000 -
Click on Start > Control Panel > Network and Internet > Network and Sharing Center. Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your network adapter and select Properties. Step 3 Highlight Internet Protocol (TCP/IP) and click Properties. Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the routers LAN IP address is 192.168.11.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set the Default Gateway the same as the LAN IP address of your router (I.E. 192.168.11.1). Set Primary DNS the same as the LAN IP address of your router (192.168.11.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP. Step 5 Click OK twice to save your settings. D-Link DIR-815 User Manual 158 Appendix B - Networking Basics Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-815 offers the following types of security:
WPA2 (Wi-Fi Protected Access 2) WPA (Wi-Fi Protected Access) WPA2-PSK (Pre-Shared Key) WPA-PSK (Pre-Shared Key) What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP:
Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing algorithm and by adding an integrity-checking feature, ensures that the keys havent been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computers hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your wireless router or access point. WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. D-Link DIR-815 User Manual 159 Appendix B - Networking Basics Technical Specifications Device Interfaces 802.11 ac/n/g/a/b wireless LAN Four 10/100 LAN ports One 10/100 WAN port One USB 2.0 port Antenna Types Four external antennas Standards IEEE 802.11ac1,2,3 IEEE 802.11n IEEE 802.11g IEEE 802.11b IEEE 802.11a IEEE 802.3 IEEE 802.3u Security WPA - Personal/Enterprise WPA2 - Personal/Enterprise Wi-Fi Protected Setup (WPS) PIN/PBC Power Input: 100 to 240 V AC, 50/60 Hz Output: 12 V DC, 1 A Operating Temperature 0 to 40 C (32 to 104 F) Storage Temperature
-20 to 65 C (-4 to 149 F) Operating Humidity 10% to 90% maximum (non-condensing) Storage Humidity 5% to 95% maximum (non-condensing) Certifications CE LVD RoHS Dimensions & Weight L = 202 mm (7.95 inches) W = 132 mm (5.20 inches) H = 28 mm (1.09 inches) 360 g (12.7 ounces) 1 Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n, and 802.11ac specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely affect wireless signal range. 2 Frequency Range varies depending on countrys regulation. 3 The DIR-815 does not include 5.25-5.35 GHz & 5.47-5.725 GHz in some regions. D-Link DIR-815 User Manual 160 Appendix C - Technical Specifications Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Note The country code selection is for non-USA models only and is not available to all USA models. Per FCC regulations, all WiFi product marketed in the USA must be fixed to USA operational channels only. D-Link DIR-815 User Manual 161 Appendix D - Regulatory Statements IMPORTANT NOTICE:
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. D-Link DIR-815 User Manual 162 Appendix D - Regulatory Statements Korea KCC (RRA) 1. 2. 3. (B ) , . 1. This wireless/radio equipment has a possibility of radio interference during operation. 2. This wireless/radio equipment cant be used for services of safety in human life because it has a possibility of radio interference. 3. As an electromagnetic wave equipment for home use (Class B), this equipment is intended to use mainly for home use and may be used in all areas. D-Link DIR-815 User Manual 163 Appendix D - Regulatory Statements NCC
:
:
MPE(MPE) 1 mW/cm2 0.52 mW/cm2 D-Link DIR-815 User Manual 164 Appendix D - Regulatory Statements Frequency Band(s) Frequenzband Frquence bande(s) Bandas de Frecuencia Frequenza/e Frequentie(s) 5.15 5.25 GHz 5.25 5.35 GHz 5.47 5.725 GHz 2.4 2.4835 GHz 5 G 2.4 G Max. Output Power (EIRP) Max. Output Power Consommation dnergie max. Potencia mxima de Salida Potenza max. Output Max. Output Power 200 mW 200 mW 1 W 100 mW D-Link DIR-815 User Manual 165 Appendix D - Regulatory Statements
This product uses the FCC Data API but is not endorsed or certified by the FCC