DSH-G200 D-Link Corporation DSH-G200 Omna Z-Wave Bridge Users Manual Version 1.0 May. 12th, 2017 Page 1 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;
(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. MPE1mW/cm2 20 cm DSH-G200 D-Link Corporation Table of Contents 1. PRODUCT DESCRIPTION .................................................................................. 3 2. APPEARANCE ..................................................................................................... 3 3. APPLICATIONS ................................................................................................... 4 4. INSTALLATIONS & BASIC CONFIGURATIONS ........................................... 4 Page 2 DSH-G200 D-Link Corporation 1. PRODUCT DESCRIPTION The DSH-G200 is a Z-Wave smart home bridge supporting S2 security and working with Apple HomeKit app to manage Z-Wave nodes to communicate with other HomeKit related devices. 2. APPEARANCE Top LED: Status indicator Wireless button: Z-Wave pairing/un-pairing Rear LAN port x1 Micro USB: Power jack, 5V/1.A or 1.2A Bottom Reset button Mounting installation Page 3 DSH-G200 D-Link Corporation 3. APPLICATIONS 4. INSTALLATIONS & BASIC CONFIGURATIONS Step 1 Make sure your DSH-G200 is powered on and near by your iOS devices. Step 2 Open Home and tap Add Accessory or tap to add the DSH-G200 to your home. Page 4 DSH-G200 D-Link Corporation Step 3 Wait for the DSH-G200 to appear, then tap it. (Note: If asked to Add Accessory to Network, tap Allow.) Step 4 Scan the eight-digit HomeKit code on the DSH-G200 or its documentation. Or enter the code manually. Step 5 Add information about your DSH-G200, like its name or the room it's located in. Siri will identify the DSH-G200 by the name you give it and the location it's in. Step 6 Tap Next, then tap Done to finish the setup. Note:
1. Press the wireless button to enter inclusion mode to include Z-Wave nodes. 2. Press the wireless button for more than 5 seconds to enter exclusion mode to remove Z-Wave nodes. Page 5