FCC ID: 2APCQ-TAC-106A Infrared Sensor Wireless Charge Holder

Infrared Sensor Wireless Charge Holder USER MANUAL Wireless holder Input voltage DC 5V/9V Input current 2A Output power 5W / 7.5W / 10W Frequency 115-205KHZ QC 3.0 car charger Input voltage DC 12-24V Output Current 5V 3A, 9V 2A, 12V 1.5A LED Mode:

Working state LED light color Power transfer Red,blue,red blue light turn on by turns for once,then off Standby mode Light off Charging Red light keeps on FOD Warning Red light keeps flashing Charge complete Red light keeps on Please read the instructions carefully before using. Pictures are for reference only, Specifications are subject to the physical product Please use the product correctly according to instructions Please do not disassemble the product or throw it to fire and water, to avoid leakage caused by electrical short circuit Please do not use wireless charger in high temperature, wet, corrosive environment, to avoid leakage from caused by damaged circuit Please do not put wireless charger close to cards with magnetic stripes or chips (ID card, credit card etc.) to avoid demagnetization Please keep wireless charger at least 20 CM distance away from implantable medical device

(heart pacemaker, Implantable cochlea etc.) to avoid potential interferences Please do safekeeping, do not let your kids treat wireless charger as toy to avoid unwanted accidents The pictures only supplies the reference, please take the actual product as the standard What is included:

Features:

Parameters:

Parameters:

Infrared Sensor Wireless Charger Holder X 1 Air vent mount X 1 QC3.0 car charger X 1 USB cable X 1 Car holder with wireless charging fuction, charges your phone conveniently when driving. Advanced infrared sensor system, automatically open and clamp your phone onto the mount. Power output 5W/7.5W/10W, compatible with all phones with QI standard. Full 360 degrees rotation for perfect viewing angle. Start charging once as the phone contact with the holder, no need cable anymore. Fix foot support to fit any size of phone, much convenient for use. QC 3.0 USB car charger included so you can start charging readily, with over temperature, over current, over voltage muti-safety protection. Compatible devices:

Work well with: iP XS Max / NOTE 8 / 9 / iP XR /

8P / iP XS / iP X / S8 / S9 / iP 8. Also work with all other Qi enabled devices. Qi disabled devices with wireless receiver or wireless charging case. Require receiver compliant with WPC Qi standard to match). Infrared Sensor Wireless Charger Holder Air vent mount There are three levels of locking for different size AC vent blades. Loose First position Transmitter coil Clamp arms stretchable range 59-91mm Touch switch Second position Third position Infrared Sensor Support foot Micro USB port

. 1 8

2 5 m m

. 2 5

3 5 m m W i i t h n 1 8 m m

. 1. Insert the adjuster into the ball joint adapter. 4. Connect the cable micro head to your charge holder. 2. Insert the ball into the socket at the back of bracket and tighten. 5. Connect the other end to car charger, then insert the car charger to car cigar lighter. 3. Insert the mount directly into the car air vent blade, set the locking switch to proper position. 6. The holder clamps will open automatically when the phone is near 2-3 inches from the infrared sensor 7. After the phone has been placed in the holder, the clamps close automatically and start charging. 8. The clips will open automatically when you touch the touch sensitive swtich in side edge, take your phone away 9. The clamps close automatically FCC Warning:

This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC RF exposure statement:

The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Product specification:

Attentions:

Attentions:

Attentions:

Attentions:

x23.7x17mm Infrared Sensor Wireless Charge Holder Input: 5V 2A 9V 2A Output: 5W/7.5W/10W (max) FCC ID:2APCQ-TAC-106A MADE IN CHINA Model : TAC-106A Chuang Long Electronics Limited Infrared Sensor Wireless Charge Holder Input: 5V 2A 9V 2A Output: 5W/7.5W/10W (max) FCC ID:2APCQ-TAC-106A MADE IN CHINA

C5266091_X10_Ed.1 DONGGUAN CHUANGLONG ELECTRONICS LIMITED Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/31/2020 Subject: Request for Confidentiality FCC ID: 2APCQ-TAC-106A To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Long-Term Confidentiality Short-Term Confidentiality Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info No No No No No No No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: AnZhang Liao Date: 7/31/2020 Title: President 1/1

DONGGUAN CHUANGLONG ELECTRONICS LIMITED Statement Product Name: Infrared Sensor Wireless Charge Holder Model No.: TAC-106A, YT-701 We( DONGGUAN CHUANGLONG ELECTRONICS LIMITED ; King Long industrial district, xiekeng village, qingxi town, Dongguan city, Guangdong China ) hereby state that all models above are identical in interior structure, electrical circuits and components, and just the model names are different for marking requirement. Signature:

Name / title:AnZhang Liao / President Tel: +86-0769-82098608 Date: 2020/7/30

C5266091_X8_Ed.1 Letter of Authorization DONGGUAN CHUANGLONG ELECTRONICS LIMITED Infrared Sensor Wireless Charge Holder Company: DONGGUAN CHUANGLONG ELECTRONICS LIMITED Address: King Long industrial district, xiekeng village, qingxi town, Dongguan city, Guangdong China Product Name:

Model Number: TAC-106A, YT-701 FCC Identifier: 2APCQ-TAC-106A We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: AnZhang Liao Date: 7/31/2020 Title: President Signature of applicant:

1/1