FCC ID: 2BB3M-LIMITLESS5 2.4G broadcasting module

YK2023A03 1.Introduction The LIMITLESS 5 series module is a remote ID module board solution that meets the specifications launched by our company for Uavs. Based on the BLE 5.3 SOC scheme, it has the advantages of small size, light weight, low cost, and easy to use. The product can transmit data through UART, SPI interface, easy to use, flexible installation, easy to expand. 2.Features Based on the Bluetooth BLE 5.3 SOC scheme Small size: 27x14x1mm Light weight: 0.8 g Transmission distance: 150m (open without interference) Low power consumption: < 4.0mA @5V (unbroadcast state) 3. Product specifications classes parameter 150m 10ms 3.6-5.5 V Distance interval working voltage power dissipation operating temperature storage temperature size weight communication interface UART115200 27 x 14 x 1 mm

-30~70

-40~85 0.95g TBD 1 YK2023A03 4.Mechanical specifications SIZI 27.0 * 14.0 * 1.0 mm 5. Pin assignment Num 1 2 3 4 5 6 name MISO MOSI SCK CS GND VCC description SPI data output signal SPI data input signal SPI clock signal SPI signal GND POWER 5V FCC Warning Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15.247 2.3 Specific operational use conditions This transmitter/module and its antenna(s) must not be co-located or operating in conjunction with any transmitter. This information also extends to the host manufacturers instruction manual. 2.4 Limited module procedures Not applicable 2 2.5 Trace antenna designs It is not applicable as trace antenna which is not used on the module. YK2023A03 2.6 RF exposure considerations This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This compliance to FCC radiation exposure limits for an uncontrolled environment, and minimum of 20cm separation between antenna and body. The host product manufacturer would provide the above information to end users in their end-product manuals. 2.7 Antennas PCB antenna; 1.74dBi; 2.402 GHz2.480GHz 2.8 Label and compliance information The end product must carry a physical label or shall use e-labeling followed KDB784748D01 and KDB 784748 stating Contains Transmitter Module FCC ID: 2BB3M-LIMITLESS5. 2.9 Information on test modes and additional testing requirements For more information on testing, please contact the manufacturer. 2.10 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity. FCC Statements

(OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module. For 15 B (15.107 and if applicable 15.109) compliance, the host manufacturer is required to show compliance with 15 while the module is installed and operating. Furthermore the module should be transmitting and the evaluation should confirm that the module's intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has to apply the appropriate equipment authorization (e.g. Verification) for the new host device per definition in 15.101. Integrator is reminded to assure that these installation instructions will not be made available to the end-user of the final host device. The final host device, into which this RF Module is integrated has to be labeled with an auxiliary label stating the FCC ID of the RF Module, such as "Contains FCC ID:2BB3M-LIMITLESS5". This device complies with part 15 of the FCC rules. Operation is subject to the following two 3 YK2023A03 conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The Integrator will be responsible to satisfy SAR/ RF Exposure requirements, when the module integrated into the host device. Module statement The single-modular transmitter is a self-contained, physically delineated, component for which compliance can be demonstrated independent of the host operating conditions, and which complies with all eight requirements of 15.212(a)(1) as summarized below. 1) The radio elements have the radio frequency circuitry shielded. 2) The module has buffered modulation/data inputs to ensure that the device will complywith Part 15 requirements with any type of input signal. 3) The module contains power supply regulation on the module. 4) The module contains a permanently attached antenna. 5) The module demonstrates compliance in a stand-alone configuration. 6) The module is labeled with its permanently affixed FCC ID label. 7) The module complies with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. 8) The module complies with RF exposure requirements. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. 4

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BB3M-LIMITLESS5

[Drone-Clone Xperts, Inc.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicant signature)

(Matthew kenney)

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-14-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BB3M-LIMITLESS5

[rone-Clone Xperts, Inc.] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Applicant signature)

(Matthew kenney)

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States Section 2.911(d)(7) USA Agent for Service of Process FCC ID: 2BB3M-LIMITLESS5 2.911(d)(7) USA Designated Agent for Service of Process We, [Drone-Clone Xperts, Inc.] (the applicant) designate [Drone-Clone Xperts, Inc.] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent & Applicant Company name: Drone-Clone Xperts, Inc. Address: 13 Carrington Way, Morristown NJ, 07960 Unites States Contact Name: Matthew kenney Telephone No: 973 610 3613 Email: Admin@droneclonexperts.com FRN: 0034003038 Signature:

Date:Sep.14, 2023 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-comm unications-supply-chain-through-the 2.911 (d)(7)USA Agent v1.2

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States Agent Authorization Company: Drone-Clone Xperts, Inc. Address: 13 Carrington Way, Morristown NJ, 07960 Unites States Product Name: 2.4G broadcasting module Model Number(s): LIMITLESS 5 Product Description: 2.4G broadcasting module We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2023-09-18 Name:

Company: Drone-Clone Xperts, Inc. Matthew kenney

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States RE FCC ID: 2BB3M-LIMITLESS5 To the certification reviewer:

We are hereby applying for [full] modular approval of the above-referenced FCC ID, based on compliance with [all] of the criteria as detailed below. Sincerely,

[Matthew kenney]

[General Manager]

Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212

(i)

(ii) Requirement per 15.212 radio elements of The transmitter must have shielding. the modular their own RF reference Shielding is provided by a metal cover over the circuitry. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided. All modulation and data inputs are buffered by circuitry on the transmitter chip.

(iii) The modular transmitter must have its own power supply regulation. Power supply regulation is provided by circuitry on the transmitter chip.

(iv) The modular transmitter must comply with the antenna and system requirements of 15.203, 15.204(b) and 15.204(c). transmission

(v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during for compliance with Part 15 testing parameters.

(vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module label is referring to the enclosed module. installed must also display a The antenna is fixed. Testing was performed in a stand-alone configuration as shown in the test setup photos. The modular was labeled with its own FCC ID. The outside of device in to which the module is installed will labeled Contains TX FCC ID: 2BB3M-LIMITLESS5, Please refer to User Manual. Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States

(vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular is comply with all applicable FCC rules. Any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions.

(viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. This module operates under Part 15. 247 which is exempt from RF exposure evaluation owing to the very low operating power.

Drone-Clone Xperts, Inc. 13 Carrington Way, Morristown NJ, 07960 Unites States Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BB3M-LIMITLESS5 Date: 09-14-2023 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Contact person: Matthew kenney