FCC ID: YE3800C Mobile Tablet

DT398H DT398H BASIC OPERATION GUIDE INTRODUCTION Thank you for acquiring the latest addition to DT Researchs line of mobile tablets the DT398H. Featuring an IP65-rated, slim yet robust enclosure, the three-pound DT398H with 9.7 TFT display is powered by the Intel Core i dual core processor, offering optimal combinations of performance and power savings. The DT398H is available with Microsoft Windows Embedded Standard 7, 7 Professional, Embedded Standard 8 or 8.1 Industry Pro, or Linux operating systems. Each software operating system features web browser, client/ server computing software, media player, accessories, and applications support. PACKAGE CONTENTS DT398H with internal battery pack, stylus, and bumpers AC-DC Power Adapter with Power Cord Basic Operation Guide Handstrap ENGLISH 1 DT398H Input/ Output Ports A e-SATA USB Hybrid Port Headphone Jack DC Power Input Full Slot Smart Card Reader SD Slot Button Functions BUTTON ACTION Power on, Push/release typically enters Standby mode, or Push/release exits Standby mode or restarts device (software dependent) Push and hold (over 4 seconds) invokes hardware shutdown Programmable, As scanner trigger when equipped with the scanner module Programmable B C D E ENGLISH 2 DT398H Power/Battery LED Status:

Blue indicates the battery is 25% to 100% charged Blinking blue indicates the battery is charging Orange indicates that the battery is between 11% to 25%

Blinking orange indicates that the battery is below 10%

Blinking blue and orange alternately indicates the battery is being warmed up. Do not unplug the AC/DC adapter. Precautions Always exercise care when operating and handling the DT398H. Do NOT apply excessive pressure to the display screen. We recommend using the Stylus provided to keep the screen clean. Avoid prolonged exposure of the display panel to any strong heat source. Wherever possible, the DT398H should face away from direct light to reduce glare. If the AC-DC power adapter is used to recharge or power the device, do NOT use any AC-DC adapter other than the one provided with the device or acquired from the manufacturer or its partners. In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power off the DT398H and disconnect all power sources. Report the problem to your device provider immediately. Never attempt to disassemble the DT398H, as this will void the warranty. The DT398H internal battery is designed for wide temperature usage. Please do not use it for other tablet models.

(The wide temperature design is not applicable for external batteries.) THE DT398H Basic Features The DT398H wireless tablet integrates a bright and responsive touch display, 1 e-SATA USB Hybrid port, and embedded networking elements such as wireless LAN or optional 3G. A DT398H typically integrates an 802.11a/b/g/n/ac wireless LAN (WLAN) adapter that may connect to other wireless devices or access points. If your DT398H does not come with such a network adapter, please consult your device provider to establish the desired network connectivity. ENGLISH 3 DT398H OPERATION Internal Battery Warning!

The Internal battery pack should only be replaced by an authorized DT Research service representative. Please contact your product and/or service provider for internal battery replacement service. Powering ON and OFF To activate the DT398H, push and quickly release the Power Button. The display will come on in a few seconds. To put the DT398H in Standby mode, push and quickly release the Power Button. To turn the DT398H off for extended storage, power off the device safely using any software function that shuts down computer provided in the software operating system. NOTE:

The battery packs shipped with your device may be low in powerplease use the AC-DC adapter with the DT398H when setting up the device for the first time to fully charge the internal battery pack. You may charge the external battery pack with it attached to the DT398H, or with the optional external battery charger kit. NOTE:

When the battery pack(s) is (are) charging, the blue-colored Battery LED should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking activity and the LED stays dark, the battery pack(s) may have been drained substantially. Try unplugging/ replugging the AC-DC adapter to the DT398H a few times to activate the charging process. NOTE:

To conserve power, use (push and quick release) the Power Button to put the device in Standby mode while not in use. Pushing briefly on the same button will wake up the system within seconds. NOTE:

Avoid using the Power Button (hold 4+ seconds feature) to turn off the devicethis form of hardware shutdown is intended to be a means of recovery from device lockups, and not as normal operation. ENGLISH 4 DT398H Start Up If the power up (from Standby or otherwise) is successful, the appropriate interface will be displayed after a launch sequence of several seconds. The wireless LAN connection may take 10-15 seconds to be established. Configuring the Mobile Tablet The device may be configured using the utilities and methods dictated by the software operating system. The DT398H should be configurable for various properties such as user profiles, network features, and several system elements. Calibration The touch display for the DT398H is calibrated before shipping. In the event that the calibration has been modified or is unsatisfactory, the respective calibration routines (e.g., PenMount (PM) to calibrate the touch interface may be used. Such applications are typically executed through touch input via Stylus or through mouse click via a USB mouse. Wireless Networking Wireless LAN The DT398H is often delivered with an embedded (user-inaccessible) 802.11a/b/g/n/ac WLAN adapter equipped with a hidden custom antenna. Through the support of typical WLAN adapters, the DT398H should be able to detect all 802.11 access points in the vicinity for you to select the access point of your choice for connection. The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT398H and the access points have to match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secure access. When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your networking equipment literature to properly configure associated settings such as Authentication mode, etc. Refer to the access point operating manuals for setting up the 802.11 access points. ENGLISH 5 DT398H Bluetooth Management Where supported by software, many of the hard buttons on the DT398H are programmable to perform a function of the users choice. To activate the button re-assignment application, invoke the Button Manager application. Brightness Control To control the screen brightness, launch the System Utility. The System screen will display a Brightness control section with up and down arrows that can be activated with the stylus. Battery and Power Management The DT398H is equipped with an internal 1880mAh Li-Ion battery pack that is capable of supporting approximately 3 - 4 hours of continuous operation. The period between battery recharges can be significantly lengthened by putting the device into Standby mode through the Power Button (see Buttons Function Table) whenever the device is not in use. Depending on the operating software, the DT398H may also be configured to enter various power-saving modes via the Power Button or through timed entry. ENGLISH 6 DT398H USING THE Mobile Tablet Peripherals Support Through its e-SATA USB Hybrid port, the DT398H supports a wide range of USB-based peripherals. These peripherals are applicable for software installation, applications storage, data storage, software recovery and update. For More Support Users can download the Software Utility and Modules Operation Guides from the DT Research website. If the DT398H comes with a 3G module, please contact your product and/or service provider for the SIM Card Slot Location and Insertion Guide. ENGLISH 7 DT398H SPECIFICATIONS System CPU RAM Storage Operating System Display Display Resolution Trusted Platform Module Fan Control Switch and Buttons Indicator Microphone Speaker SD Slot NIST Compliant Sensor I/O Ports USB 2.0 Port Headphone-out DC-in Full Slot Smart Card Reader Mechanical and Environmental AC/DC Adapter Battery Pack Enclosure Stylus Protective Grips Dimensions (H x W x D) Weight Water and Dust Resistance Regulatory Intel Core i7, 1.8GHz 8GB DDR3L 64GB Microsoft Windows Embedded Standard 7, 7 Professional, Embedded 8 Standard, 8.1 Industry Pro or Linux 9.7 LED-backlight outdoor display with capacitive touch; Sunlight readable display with resistive touch option 1024 x 768 (XGA) Yes, TPM 1.2 support Yes 1 power button, 3 side buttons, 1 trigger button and 1 Wi-Fi switch 1 power/ battery status LED and 1 WLAN active LED Built-in Microphone Built-in speaker Yes, up to 64GB Yes Built-in gyroscope sensor, e-Compass sensor, pressure sensor and 3-axis accelerometer 1 eSATA USB hybrid port 1 1 Reads ISO 7816 T=0, T=1; 1.8/3/5V smart card Input: 100 240V AC; Output: 19V DC, 6.31A Internal 14.8V, 1880mAh ABS + PC plastics Yes, capacitive touch stylus Rubber bumpers on each corner with handstrap for handling protection 9.05 x 10.8 x 1.4 inch/ 230 x 275 x 35 mm 3.1lbs/ 1.4kgs IP65* IP65 rating may not be applicable for units with module options FCC Class B, RoHS compliant Operation: 32F to 104F (0C to 40C);

Govt/Military: -4F to 122F (-20C to 50C) Storage: -4F to 140F (-20C to 60C) 0% 90% non-condensing DT Research, Inc. 2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com Copyright 2014, DT Research, Inc. All Rights Reserved. DT Research is a registered trademark of DT Research, Inc. BOG020713DT365CTMDENG Temperature Humidity ENGLISH 8

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Operation on the 5.15-5.25GHz frequency band is restricted to indoor use only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the potential for harmful interference to co-channel Mobile Satellite Systems. RF Exposure Information (SAR) This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. This device was tested according to FCC SAR procedure, and was tested directly contacted with the Body. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines.