S90HD 4.1 Channel Soundbar Home Theatre System User manual Whats in the Box 2 Box contents Soundbar Wall mount bracket Wireless active subwoofer Remote control Left rear surround speaker (SL) Right rear surround speaker (SR) Fiber optic input audio cable Audio cable Adapter audio cable HDMI cable Speaker connecting cable for rear surround speakers Plastic wall anchor x10 Rubber pad x4 Screws for bracket x4 Screws for wall mounting brackets x10 Bracket x2 User manual Illustrations 3 view Back rear surround speaker (SR) of Back view of soundbar Back view of subwoofer Back view of rear Front view of soundbar
(SL) speaker surround 1. Connect to right rear surround speaker (SR) 2. HDMI 1 input 3. HDMI 2 input 4. HDMI ARC output (Audio Return Channel) 5. Optical input 6. Coaxial input 7. Line in input 8. AUX input 9. Subwoofer/SR speaker pairing button on soundbar 10. Display window 11. Master volume control/input selector Rotate: Volume +/-
Press: Audio source selection (HDMI1HDMI 2HDMI ARCLine inAUXBluetoothOpticalCoaxial) Press: Power ON Press and hold: Standby 12. Status indicator 13. Soundbar pairing button on the subwoofer 14. Power switch 15. Power cable 16. Soundbar pairing button on the SR speaker 17. Status indicator 18. Connect to left rear surround speaker (SL) 19. Power cable Remote Control Illustration 4 1. Power ON/standby 2. Mute/mute off 3. Optical input 4. Bluetooth input(press and hold to disconnect Bluetooth) 5. Coaxial input 6. HDMI 1 input 7. HDMI 2 input 8. HDMI ARC output 9. Line in input 10. AUX input 11. Dolby sound effect enabled 12. Dolby sound effect disabled 13. Music mode 14. Movie mode 15. Emulate mode 16. Matrix mode 17. Virtual mode 18. Game mode 19. Volume up 20. Volume down 21. Bluetooth mode: Previous track 22. Bluetooth mode: Next track 23. Bluetooth mode: Play/pause 24. Dolby Compression enabled 25. Dolby Compression disabled 26. Reset: press and hold to restore to factory settings 27. Multifunctional tuning 28. Adj+ : Each component increase progressively 29. Adj - : Each component decrease progressively Remote Control Illustration 5 How to operate remote control 1. Point the remote control to the IR window on soundbar. 2. The optimum operational distance is within 7 meters. 3. The optimum operational scope is within a 60 degree angle. Install the battery Please refer to the illustration to open the battery compartment, load the batteries and close the compartment. Note:
1. Do not place the remote control in places that are hot and humid. 2. Do not charge the batteries. 3. Remove the batteries when unused for extended periods. 4. The battery should not be exposed to excessive heat such as direct sun, fire or related. 5. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Wall Mount Bracket Installation 6 1. Soundbar Drill hole in wall Drill 4 holes (Depth: 40mm/1.5, Hole size: 8mm/1/4) in the wall using the wall mount bracket as a template, then knock wall anchor into holes. Note:
Dimension of hole may vary depending on wall materials, therefore please adjust drill size to existing conditions for proper installation. Attach wall mount bracket Align mounting bracket to the holes and use screws to attach wall mount bracket Wall Mount Bracket Installation 7 Place soundbar onto the wall mount bracket Please make sure all audio cable connections are secure before mounting the speaker. Warning: Please follow installation instructions to avoid damage to your product. Wall Mount Bracket Installation 8 2. Rear surround speakers Drill hole in wall For each rear surround speaker, drill 2 holes (Depth: 40mm/1.5, Hole size: 8mm/1/4) in the wall using the bracket as a template, then knock wall anchor into holes. Note:
Dimension of hole may vary depending on wall materials, therefore please adjust drill size to existing conditions for proper installation. Fix bracket on the wall Align bracket to the holes and use screws to attach. Wall Mount Bracket Installation 9 Attach rear surround speakers to wall bracket Place rubber pad between rear surround speakers and brackets to prevent vibration. Align rubber pads to the holes on the bracket; then align screws on the bottom of speakers to the rubber pad holes on the brackets and tighten the screws. Warning: Please follow installation instructions to avoid damage to your product. Connection 10 LINE IN input Optical input TV/DVD Blu-ray DVD Set Top Box TV Box 1. As the illustration shows, connect to audio source using the corresponding audio cable. 2. As the illustration shows, connect speakers to power source using the corresponding power cable. 3. Turn on main power switch and your speakers should be ready to go. How to Pair Your Speakers 11 Pair soundbar with wireless active subwoofer Subwoofer Soundbar Pair Soundbar has been paired with subwoofer before leaving the factory. Hence the wireless connection will resume automatically when both soundbar and subwoofer are powered on and the red indicator is lit. If the wireless connection fails to resume, please follow these steps below to re-pair. 1. Power on the subwoofer, the red indicator should blink in a breathing pattern, which means no active wireless connection. 2. Press and hold the "Pair" button on back panel of the subwoofer for 2 seconds to put it into pairing mode. The red indicator will blink rapidly. 3. Press and hold the "Pair" button on back panel of soundbar to put it into pairing mode. 4. Wait until the red indicator on subwoofer is lit constantly. The pairing is complete and wireless connection is made. LED indicator blinks in a breathing pattern: subwoofer is disconnected and enters standby mode LED indicator blinks rapidly: subwoofer enters pairing mode LED indicator is constantly lit: subwoofer is connected. S70DB Pair soundbar with right rear surround speaker (SR) Right rear surround speaker (SR) Soundbar Pair Soundbar has been paired with right rear surround speaker before leaving the factory. Hence the wireless connection will resume automatically when both soundbar and SR speaker are powered on and the red indicator is lit. If the wireless connection fails to resume, please follow these steps below to re-pair. 1. Power on SR speaker, the red indicator should blink in a breathing pattern, which means no active wireless connection. 2. Press and hold the "Pair" button on back panel of SR speaker for 2 seconds to put it into pairing mode. The red indicator will blink rapidly. 3. Press and hold the "Pair" button on back panel of soundbar to put it into pairing mode. 4. Wait until the red indicator on SR speaker is lit constantly. The pairing is complete and wireless connection is made. LED indicator blinks in a breathing pattern: SR speaker is disconnected and enters standby mode LED indicator blinks rapidly: SR speaker enters pairing mode LED indicator is constantly lit: SR speaker is connected Operations Guide 12 1. Press the Master volume control/input selector knob on soundbar or the corresponding audio source button on the remote control to select audio source. 2. Play music and adjust to the comfortable volume. Bluetooth or Note:
Only the standard PCM audio signals (44.1KHz/48KHz/96KHz) and Dolby/DTS audio coded signals function in optical/coaxial mode. Bluetooth Function 13 or Bluetooth 1. Press the Master volume control/input selector" knob on soundbar or button on the remote control to select Bluetooth mode. The display window shows Bluetooth mode. 2. Set your Bluetooth device (mobile phone, tablet etc.) to search for and connect to EDIFIER S90HD. 3. PIN code for connection is 0000 if needed. 4. To disconnect Bluetooth, please press and hold button on the remote control Note:
1. Bluetooth connectivity and compatibility may be different between different source devices, depending on the software versions of source devices. 2. To enjoy all Bluetooth functions of this product, please ensure your mobile device has A2DP profile. HDMI Operation 14 HDMI input/output or HDMI 1/HDMI 2 mode 1. Press the "Master volume control/input selection" knob on soundbar or the "HDMI 1" / "HDMI 2"
button on the remote control to select HDMI 1/HDMI 2 mode. The display window shows
"HDMI 1" / "HDMI 2. 2. Connect audio source (like DVD) to "HDMI 1" or "HDMI 2 input port on the back panel of soundbar using HDMI cable. 3. Connect HDMI connector on the TV to HDMI ARC output port on the back panel of soundbar using another HDMI cable. Audio source video signal will output to TV. (Note: You have been supplied with one HDMI cable; additional cables may be necessary.) HDMI ARC mode 1. Press the "Master volume control/input selection" knob on soundbar or the "HDMI ARC" button on the remote control to select HDMI ARC mode. The display window shows "HDMI ARC. 2. Connect HDMI ARC connector on the TV to "HDMI ARC" output port on the back panel of soundbar using HDMI cable. 3. HDMI ARC will return audio signal to the speaker via HDMI cable. Specifications 15 Power output: R/L (Treble): 12W+12W R/L (Mid-range): 32W+32W SR/SL (Mid-range): 22W+22W SW: 70W Frequency response: 40Hz~20KHz Input: HDMI/AUX/LINE IN/Bluetooth/Optical/Coaxial Note:
Reference frequency used for electrical parameter during test: treble is 10KHz; mid-range and bass is 500Hz;
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, DTS and the Symbol together, and Digital Surround are registered trademarks and/or trademarks of DTS, Inc. in the United States and/or other countries. DTS, Inc. All Rights Reserved. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries." This sentence may be translated into local languages upon approval by HDMI Licensing Administrator, Inc.