smartTouch Swipe User Manual Doc No. 720100010 Version 1 Copyright 2015 by Embed International Notice of Rights All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of Embed. For more information on getting permission for reprints and excerpts, contact Embed. Notice of Liability The information in this document is distributed on an as is basis, without warranty. While every precaution has been taken in the preparation of this document, neither the author or Embed shall have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the instructions contained in this document or by the computer software or hardware products described herein. www.embedcard.com Embed Asia-Pacific Head Office 2 Neil Street Osborne Park, WA 6017 Australia Telephone +61 (8) 9340 0100 Facsimile +61 (8) 9340 0199 Information: info@embed.com.au Sales: sales@embed.com.au Support: support@embed.com.au Embed North & South America 1621 West Crosby Rd. Suite 100A Carrollton, TX 75006 United States Telephone (469) 521-8000 Facsimile (214) 260-0976 Information: info@embedcard.com Sales: sales@embedcard.com Support: USAsupport@embedcard.com Embed Middle East
#1504, Indigo Icon. PO Box 37307 Jumeirah Lakes Towers Dubai, UAE Telephone +971 (4) 4356331 Facsimile +971 (4) 4356332 Information: infoME@embedcard.com Sales: salesME@embedcard.com Support: supportME@embedcard.com Embed UK and Europe 14 The Maltings Brassmill Lane Bath BA1 3JL United Kingdom Telephone +44 (0)1225 311 323 Facsimile +44 (0)1225 445 217 Information: infoUK@embedcard.com Sales: salesUK@embedcard.com Support:supportUK@embedcard.com www.embedcard.com 1 Table of Contents LIST OF ACRONYMS .............................................................................................................................................. 2 SAFETY INFORMATION ........................................................................................................................................ 3 PROTECTING AGAINST ELECTROSTATIC DISCHARGE ................................................................................................. 3 OTHER INFORMATION AND WARNINGS: ..................................................................................................................... 3 INTRODUCTION ...................................................................................................................................................... 4 MAJOR COMPONENTS ............................................................................................................................................... 4 RECOMMENDED INSTALLATION HARDWARE ............................................................................................................ 5 PRE-INSTALLATION .............................................................................................................................................. 6 SMARTTOUCH SWIPE READER INSTALLATION .......................................................................................... 7 VIDEO GAME INSTALLATION .................................................................................................................................... 9 HARNESS CONNECTIONS ........................................................................................................................................... 9 POWER 12 VOLT DC ............................................................................................................................................... 9 GAME CREDIT CONNECTIONS ................................................................................................................................. 10 BASIC CONFIGURATION OF THE SMARTTOUCH SWIPE ......................................................................... 11 HOW IT WORKS ..................................................................................................................................................... 11 FCC PART 15B COMPLIANCE STATEMENT .................................................................................................. 12 CE DECLARATION OF CONFORMITY ......................................................................................................... 12 VERSION HISTORY ............................................................................................................................................... 13 Notice All images presented in this document are for illustration purposes only. All procedures in this document assume a degree of technical knowledge, only persons with the appropriate qualifications and experience should implement these procedures. Acronym Description STS Wi-Fi AC DC List of Acronyms www.embedcard.com smartTouch Swipe Wireless Fidelity / IEEE 802.11b Direct Sequence Alternating Current Direct Current 2 Safety Information This guide assumes that the installer is qualified to work on electrical devices, with electronic skills and experience working with arcade machines. Do not use in life critical or applications requiring high reliability The smartTouch Swipe is not intended for use in systems that may affect human life or that require a very high degree of reliability such as medical equipment, nuclear facilities, aerospace equipment or transportation equipment. Embed does not assume any liability for accidents resulting in injury or death, or for any damages to property that may occur as a result of using the product in such facilities, equipment, or control systems. Protecting against electrostatic discharge Electrostatic discharge can damage electronic components including the Embed smartTouch Swipe. Please observe electrostatic discharge precautions for handling or installing this equipment. Other information and warnings:
Embed smartTouch Swipe is intended for operation between 55 0C and -20 OC (131 0F and -4 OF). Embed smartTouch Swipe is not intended for domestic use. www.embedcard.com 3 Introduction This manual describes the requirements and steps needed to successfully install the smartTouch Swipe. The scope of this document covers the hardware installation and the interface to common Video game type. Major Components The smartTouch Swipe The smartTouch Swipe is the guest facing device that features a touchscreen display with a dedicated contactless type cards type reader. Guests will Swipe their card for the primary purpose of transacting at games and attractions. The device can be mounted in portrait or landscape orientations to best suite the game and guest accessibility. www.embedcard.com 4 Picture shows typical mounting of device on a game Recommended Installation Hardware The following is a recommended range of hardware to securely install and mount the smartTouch Swipe reader. The smartTouch Swipe reader uses 4mm brass inserts in the base of the enclosure so the appropriate length 4mm metric screws must be used to properly secure the smartTouch Swipe reader. All other hardware can be adjusted to what is most appropriate and available in your area. M4 metric, pan head, Philips drive, and zinc coated steel screws. Used to secure the smartTouch to the surface of the game or attraction. Recommended you have lengths of 10mm, 20mm and 25mm available as a minimum. M4 metric, zinc coated steel washers. Recommended these are used under every screw. M4 metric, zinc coated steel full width nuts www.embedcard.com 5 Pre-Installation Before the installation of any hardware, verify the following:
If the mounting surface is metal, that it is adequately earthed. An adequate earth connection point exists in the game cabinet. The game credits when a coin is inserted The game accurately dispenses tickets The coin and ticket meters increment correctly Correct any identified faults and retest Disconnect the power from the game It is vital that you are certain the game is in proper working order before beginning the installation of the Embed hardware. This will prevent confusion later in the process. Never source and use wire taps or wire nuts. Wire taps cut into the wire and make a minimal connection that will deteriorate over time leading to game credit and power supply related problems. Wire nuts also offer a less-than-desirable connection on the small gauge wire used in games. Wire Swipe We recommends that crimp type butt connectors be used for wire joins and splicing. You will need some tools and hardware for the equipment installation and recommend the following as a minimum. Butt Connector Wire Nut Multi-meter Drill 5 mm drill bit Step drill bit up to 20mm Phillips screwdriver Wire stripper Crimp tool for connectors Butt connectors Cable ties www.embedcard.com 6 smartTouch Swipe Reader Installation The smartTouch Swipe reader is best mounted and fixed to a location on the game that ensures its easily accessible to guests. In many cases its recommended to mount the smartTouch Swipe reader over the existing coin entry point as it is readily accessible and allows use of the existing hole for cable entry. The smartTouch Swipe reader display is usually mounted in landscape display orientation. Landscape Orientation Step 1: Locate the ideal position to mount the smartTouch Swipe reader. Step 2: Mark the spots for drilling. Use the smartTouch Swipe reader mounting template to mark the four mounting points and the cable connection point. Step 3: Drill the four mounting points with a 5mm drill-bit. Drill a harness connection hole with a 12.5mm step drill-bit. Clear the holes of sharp edges to protect the harness. Step 4: Connect the harness to the connector in the bottom of the smartTouch Swipereader. Feed harness through the hole in the cabinet and position the smartTouch Swipe reader to line up with the screw mounting holes. Insert the correct length 4mm screws into the base of the smartTouch Swipe reader and tighten. www.embedcard.com 7 Template for the smartTouch Swipe reader mount point drill holes. NOT TO 1:1 SCALE This template is available in scale PDF format from support@embedcard.com www.embedcard.com 8 Video Game Installation Standard type Video Games are typically strait forward to install with connections to the 12v DC Power Supply and Credit Input only. From start to finish you can expect to take 25-35 minutes. Harness Required The harness required for this installation is the Standard Video Harness. Standard Video Harness Part # IOC-005 Harness Connections Power 12 volt DC Power to the IOC is supplied via the 12-way connector through the following pins:
Pin number 1 2 Wire Colour ORANGE BLACK Wire Function DC +12 v DC Ground Start by locating the games power supply, these are typically located in the base of the cabinet. Identify and measure the 12v DC output ensure it is stable and ideally between 12-13v DC. Splice in the Orange wire to +12v DC and the Black wire to DC Ground. It is important for long term reliability that this this connection is made at, or as close as possible to the Power Supply and not at a mid-point in the game harness or coin door. www.embedcard.com 9 If +12 v DC is not available from the game or is unstable then you will need to install a dedicated
+12v DC 1000mA supply. Note: its very important the DC Ground of the new power supply is commoned with the existing DC Ground of the existing in game power supply. Without this common ground ant ticket or coin monitoring will not operate correctly. Game Credit Connections Pin number 7 8 Wire Function Wire Colour ORANGE/BLACK CREDIT 1 N.O. YELLOW/BLACK CREDIT 1 COM. Note N.O. means Normally Open, COM. Means Common On the selected player station you can typically disconnect the common and normally open connectors from the existing coin switch and plug them directly into the pre fitted harness connectors. Connect the other end of the harness to the smartTouch Swipe at connector J7. www.embedcard.com 10 Basic Configuration of the smartTouch Swipe As with any configurable electronic device, the smartTouch Swipe contains settings that either control or change its behaviour without modifying hardware or software associated with the device. The smartTouch Swipe has an integrated Wi-Fi module. The smartTouch is configured to attach to the networking and security information with the use of a special staff card. How it works The smartTouch Swipe is very simple to use . User simply present their cards over the display or user to transact or insert the card in the card slot and swipe . The user only needs to ensure the card is tapped within the display area of the smartTouch Swip or the card can be Swipeped in either face up or face down in the card slot The functions available to the user include :
E-Ticket collection Start/ Play game Check Card balance Note : The smartTouch Swipe is a smart interactive device and will display messages dianamically to a user to enhance gaming experience. The game configuration is independent of the smartTouch Swipe reader and varies from game type to game type. The user descriptions for interactive gaming messages fall outside the scope of this manual. www.embedcard.com 11 FCC Part 15B Compliance Statement RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving device. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You may also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402. Any Changes or Modifications not expressly approved by Embed International or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules. This device complies with part 15 of the FCC Rules. Operation is subject to the Following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Declaration of Conformity The smartTouch Swipe equipment meets the requirement of EC dircetives for CE certification Directive 2014/53/EU the following standards are applied :
Standard EN 60950-1: 2006+A11: 2009+A1:2010+A12:2011+A2:2013 ETSI EN 301 489-1 V2.1.1, ETSI EN 301 489-3 V2.1.1, ETSI EN 301 489-17 V3.1.1, ETSI EN 300 328 V2.1.1, ETSI EN 300 330 V2.1.1, EN 62311:2008 www.embedcard.com 12 Initial document Add typical installion picture Version History V 0.0 V 0.1 T Venter T Venter 30/03/2016 21/04/2016 www.embedcard.com 13