FMAPR4400 WIFI+BT Module 15 F23BUUM13-W2 UserMan, r2 Users Manual

WIFI+BTModule F23BUUM13W2 ManualandSpec,revision1.0 ReferenceDocuments FNLINKF23BUUM13W2moduleproductspecification FMAWIFIFTSWUSBschematic Description TheFenderFMAWIFIFTSWUSBPCBAssemblyisanI/Oboard(WIFIboard)usedinthefamilyof FenderModularArchitecture(FMA)products.TheboardhasaUSBportwithamicroABconnector,a FenderFootswitchportwithaphonejackandawirelessmodule. CircuitDescription Referringtotheblockdiagram,therearethreemainsectionsofthecircuit:

FNLinkF23BUUM13W2module USBport Footswitchport CommunicationwiththeFNLinkmoduleisaccomplishedthroughaUSBportfromthe18pinmain boardheader.TheWiFiandBluetoothradiocircuitryiscontainedontheFNLinkmodule.Thereisno antennaonthemodulesotheradiooutputfromthemoduleconnectstoanFTypePCBantennaonthe PCBA.TheFNLinkmoduleoperatesfroma3.3VsupplysourceonthemainPCBthroughthe18pin header. TheUSBcircuitonthePCBAconsistsofESDprotectioncomponentsandamicroABUSBconnector. TheFootswitchcircuitonthePCBAconsistsofESDprotectioncomponentsandaphonejack connector. FNLinkModuleinstallationandUse TheFNLinkmoduleissolderedtothePCBA.PadsonthePCBAmakecontacttothe3.3Vsupply,USB portandantenna.Allcommunicationbetweenthehostprocessorandthemoduleisaccomplished throughthemodulesUSBport.AdescriptionofspecificcommandsforBluetoothandWiFidriver developmentisbeyondthescopeofthisdocumentandcanbefoundindocumentationfromRealtek fortheRTL8723BUWiFi+BTchipelsewhere. BlockDiagram FMAMainPCBInterfaceHeader Allcontrolandpowersignalscomefromaconnectiontoamotherboardthroughan18pin,2mmdual rowfemaleheader.Thepinoutfortheheaderisinthetablebelow:

Signal USB_OTG_DP USB_OTG_DN GNDD FTSW_DAT CHIP_WAKE FTSW_DET HOST_WAKE USB_OTG_5V USB_OTG_ID 3.3V USB_WIRELESS_DP GNDD USB_WIRELESS_DN reserved reserved reserved reserved reserved Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 FNLinkModule Description USBOTGportdatasignal USBOTGportdatasignal DigitalGND Footswitchportdatasignal Reservedforfutureuse Footswitchportdetect Reservedforfutureuse Reservedforfutureuse USBOTGportIDsignal 3.3VDCSupply FNLINKModuleUSBportdatasignal FNLINKModuleUSBportdatasignal Reservedforfutureuse Reservedforfutureuse Reservedforfutureuse Reservedforfutureuse Reservedforfutureuse WIFIboardisusesanFNLINKF23BUUM13W2moduleforwirelesscommunication.TheFMAmain boardcommunicatestothemodulethroughaUSBport.Thewirelessmoduleissupportsandnumberof IEEEstandardsincludingIEEE802.11b,IEEE802.11g,IEEE802.11n,IEEE802.11d,IEEE802.11e,IEEE 802.11handIEEE802.11i.THmodulealsosupportsBluetoothspecsincludingBluetooth3.0and Bluetooth4.0Dualmode.Foracompletelistofsupportedwirelessstandardspleaserefertothe productspecificationfortheFNLinkF23BUUM13W2module. Antenna AnFtypePCBantennaislocatedonthePCBtosupportthe2.4GHzsignalfromtheFNLinkmodule,and themaximumantennagainis1.0dBi. PowerConsumption OperatingVoltage WiFimodecurrent BT BoardDimensions 3.3VDC+/9%

200mA(TX/RXcontinuousmode) 2.1mA(idlepowersaving) 0.1mA(IdleorRFdisablemode) 15mA(SCOHV3) 0.9mA(InquiryandPageScan) 7.5mA(ACLnotraffic) FCC Statement:

This de vice co mplies with Part 15 of the FCC Rules. Op eration i s subject to t he following two conditions: (1) Th is device may not cause harmful i nterference. (2) This device must accept any interf erence received, i ncluding interference tha t may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digi tal device, p ursuant to Part 15 of t he FCC Rules. The se limits are designed t o provide re asonable protection against harmf ul interference in a residential installation. This equi pment generat es u ses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, t he user is encouraged to t ry to co rrect t he int erference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications not e xpressly approved b y the party responsible for compliance could void the user's authority to operate the equipment. LABEL OF THE END PRODUCT:

The final end product must be label led in a visible area with the following "Contains TX FCC ID: 2AATL-F23BUUM13". If the size of the end product is smaller than 8x10cm, then additional FCC part able in the users manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interf erence received, i ncluding interference tha t may cause undesired operation. RF Exposure 15.19 st atement is required to be avail This device has been evaluated and shown compliant with the FCC RF Exposure limits under fixed exposure conditions (antennas are greater than 20cm from a person's body) when installed in certain specific OEM configurations. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM integrator under control of the Grantee. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE:

This device is intended only for OEM integrators under the following conditions:

(1) According to FCC P art 15 Subpart C Section 15. 212, t he radio e lements o f t he modular trans mitter must have their own shieldi ng. However, due to th ere is no shielding for thi s WIFI/ BT module, this module is granted as a Li mited Modular Approval.

(2) This module has been designed to ope rate with PCBA antenna having a m aximum gain of 1.0dBi.

(3) Integration is t ypically s trictly r estricted t o Grantee hims elf or dedicat ed OEM integrators under control of the Grantee. The m odule will be responsible t o satisfy SAR/RF Exposure requirement s, when the module integrated into any (portable, mobile, fixed) host device. This module is intended for OEM integrator only and the OEM integrators and instructed to ensure that the en d user ha s no manual in structions to remove or in stall the device. The OEM integrator is st ill responsible for the FCC compliance requirement of t he end product, which integrates this module. The module has no shielding and tested stand alone. This module is tested and approved as Limited modular approval with stand alone configuration, any OEM incorporated this radio module into any system are require additional testing and evaluation. The module is only certified with the installed antenna. Any change of the antenna will void the certification. IC Notice:

This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference; and

(2) this device must accept any interference. Including interference that may cause undesired operation of the device. Avis dIndustrieCanada Le present appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exem pts de licence L'exploitation est autorise aux deux conditions suivantes:

1) I'appareil ne doit pas produire de brouillage; et 2) I'utillsateur de I'appareil doit accepter brouillage radio lectrique subi meme si le brouillage est susceptible d'encompromettre le fonctionnement. Mauvais fonctionnement de I'appareil. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclarationd'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device and its antenna(s) must not beco-located with any other transmitters except in accordance with IC multi-transmitte rproduct procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without reassess ment permissive change. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. This module isintended for OEM integrator. The OEM integratorisstillresponsible for the IC compliance requirement of the end product, whichintegratesthis module. In the usersmanual of the end product, the end user has to beinformed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to beinformed that the IC radio-frequencyexposure guidelines for an uncontrol led environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The final end product must belabeled in a visible area with the following " Contains TX IC : 12425A-F23BUUM13W2". EU Regulatory Conformance Hereby, we (FN-Link Technology Limited) declared that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.