FCC ID: 2ATDU-01446 KIN TOUCH PANEL

MEET KIN PANEL INSTALLER'S MANUAL ENGLISH Version This manual corresponds to firmware version V2.0. FERMAX ELECTRNICA S.A.U. http://www.fermax.com MEET DIGITAL VIDEO Panel manual available at https://www.fermax.com/qr/meet/

Copyright Notice Fermax and Fermax MEET panel are trademarks of Fermax Electronica S.A.U. registered in the European Union and other countries. FERMAX ELECTRNICA S.A.U., 2018. Page 3 1 Product Introduction Overview High definition camera 1,2Mpx Lighting for night vision with LEDs Speaker TFT and touch screen Motion sensor Microphone Mifare reader Slider Page 4 Panel Display Screen Network Status 2 Functions Introduction Call apartment Call guard unit Call volume settings Door opening, relay delay settings Connect exit button Speech Door opened and tamper alarm Lift control (Only when installed) Access Code Mifare reader Alarm management by access control Face Recognition for release lock Page 5 Call Apartment 2.1.1 Block Panel call apartment Visitors need enter apartment number followed by to confirm. For example, if the resident lives in apartment 2601, the visitor should enter: 2601 and press 2.1.2 General Entry Panel call apartment Visitors need to enter block number followed by a 4 digits apartment number followed by to confirm. For example, if the resident lives in block 3 apartment 2601, the visitor shall enter:

32601 and press Page 6 Call Guard Unit 2.2.1 Block Panel Call Guard Unit The visitor or resident can call the guard unit by touch concierge icon , then select the concierge that they want to call .This call can be made from all Block Entry Panels. 2.2.1 General Entry Panel Call Guard Unit The visitor or resident can call the guard unit by touch concierge icon , then select the concierge that they want to call .This call can be made from all General Entry Panels. Page 7 Access Code Press ACCESS CODE icon to access code function, entering the access code followed by KEY icon to confirm. If the access code is correct the door will open and release the lock. You can enable or disable the function at web of the panel. The access code to be defined at web of the panel, Maximum access code 8. Face Recognition Press FACE RECOG icon to key access face recognition function, the camera of the panel will start to read the face information. If the face data is authorized, the door will open and release the lock. The face data is to be added through the management software. Maximum face data 10000. Page 8 Mifare Reader Resident can access to their corresponding entrance by passing their authorized Mifare card, the door will open and release the lock. The Mifare card data is to be added through management software, Maximum 100,000 Mifare cards. 2.6 About Enter code 9999 followed by icon to confirm, The ABOUT information will show. You can get information about the device name, firmware version, IP address, MAC address. Page 9 3 Installation Connectors 10/100Mbps RJ45 Port.

+, : 12Vdc Power Input. C, NO, NC: Relay contacts for release lock, the double terminals are the same connection.

+5V, , WD0, WD1: Wigand-26 protocol output or input. BS, : Exit button.

, SP: Door-open sensor. 485+, 485-: To lift control gateway, F01491 (4 relay module). Page 10 Technical Parameters Dimensions Panel (mm): 185(W) 405(H) 53(D) Power supply: 12Vdc/POE Standby current: 330mA Working current: 500mA Technical specifications of the display:

-Size: 10 inch

-Format: 16:9

-Resolution: 1024*600 Camera pixel: 1.2 megapixels 90o visual angle: Vertical 72, Horizontal 54 Minimum illumination: 0.5Lux Maximum conversation time: 120s Door relay time: 1-9s Door delay time: 0-9s Door sensor time: 120s IC cards: 100,000 Face data: 10000 Operating temperature: 40 Relative humidity: 20%~80%, without condensation 3.3 FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Page 11 Caution:

Products can only be used below 2000m altitude For the following equipment:

Product Name: KIN TOUCH PANEL Model: 1445 1446 Brand Name: FERMAX FERMAX (SHANGHAI) ELECTRONICS CO., LTD. E-mail: richard.chen@fermax.com.cn hereby declares that this [Name: KIN TOUCH PANEL, Model: 1445,1446] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the internet address: www.xxx.com This product is intended for sale and application in a business environment. RED Article 10 2

-This product can be used across EU member states RED Article 10 10

-The product is class 1 product, No restrictions NFC:

Frequency Range: 13.56MHz Radiated H-Field: -12.6dBuA/m(@10m) 4 Installati 4.1 Installation height Page 12 4.2 Installation Guide Diagram 1. Flush box install. 2. Base flush box depth adjustment 3. The upper part of the panel is stuck in, then move the panel to the flush box. hook. 2 CM 2 CM 4. Move the slider of the panel and fix the two screws. When installing, pay attention to the reservation of the 2 CM space around the door to move the slide cover.

Reference No.: WTX22X06129359W001 Page 1 of 18 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

FERMAX ELECTRONICA, S.A.U. AV. TRES CRUCES, 133, VALENCIA 46017, Spain Date: 2022-08-26 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ATDU-01446 Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. Block Diagram Operational Description Schematics Parts List Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Internal Photos Test Setup Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. or For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, FERMAX ELECTRONICA, S.A.U. FERMAX ELECTRONICA, S.A.U. AV. TRES CRUCES, 133, VALENCIA 46017, Spain

TOMAS ANDRES/Manager

FERMAX ELECTRONICA, S.A.U. AV. TRES CRUCES, 133, VALENCIA 46017, Spain

(FCC ID2ATDU-01446) POWER OF ATTORNEY DATE: 2022-08-26 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, FERMAX ELECTRONICA, S.A.U. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, FERMAX ELECTRONICA, S.A.U.

TOMAS ANDRES/Manager

FERMAX ELECTRONICA, S.A.U. AV. TRES CRUCES, 133, VALENCIA 46017, Spain Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2022-08-26 SUBJECT: FCC Application for FCC ID: 2ATDU-01446 To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the

"accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, FERMAX ELECTRONICA, S.A.U.

TOMAS ANDRES/Manager