FCC ID: 2AX2R-WHP01K Bluetooth Headphone

 

AG-WHP01K

Bluetooth Headphone

User's Manual

取扱説 明 書

使用说明书

EN

Package contents

Product Overview

AG-WHP01K

Carrying Pouch

User’ s Manual

(Warranty Card Included)

Charging Indicator

ANC (Active Noise

Cancelling) Button

USB Charging Port

Bluetooth /ANC

Status Indicator

Power Button

Volume + Button

Volume - Button

3.5mm Audio Jack

USB Type-C

Charging Cable

Analog Audio Cable

with 3.5mm Plug

2

3

Charging the Headphones

Powering ON

Connect the USB Charging Port to a charging adaptor with the supplied USB Type-C Charging

Cable. The Charging Indicator flashes red while charging and turns green when the headphones

are fully charged.

Press and hold the Power Button for 3 seconds and the headphones will turn ON with a "Power

ON" announcement.

When the power is ON, the Bluetooth/ANC Status Indicator flashes in blue at a regular interval.

When the power is ON with the ANC function is activated, the Bluetooth/ANC Status Indicator

flashes alternately in blue and green at a regular interval.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

4

Powering OFF

Press and hold the Power Button for 5 seconds and the headphones will turn OFF with a "Power

OFF" announcement. When the power is turned OFF, the Bluetooth/ANC Status Indicator lights up

red and fades off.

* To fully turn OFF the power of the headphones, please make sure to turn OFF the ANC function

too to prevent extra power consumption. ANC function might remain ON even after turning OFF

the headphone power.

5

Activating ANC (Active Noise Cancelling) Function

Performing Device Pairing

Press and hold the ANC Button for 2 seconds and the ANC function will be activated in 2 different

ways depending on the status of the headphone.

If headphone power is ON: Announcement "Noise Cancelling" will be emitted and the

Bluetooth/ANC Status Indicator flashes alternately in blue and green at a regular interval.

If the headphone power is OFF: The Bluetooth/ANC Status Indicator will light up green.

* The ANC function can be activated even when the power is OFF. As ANC function consumes

battery power, when the headphones are not in use, please make sure that the ANC function is

properly turned OFF.

Setting

Device

WHP01K

In order to use the WHP01K with your device, initial device pairing is necessary. Once the

headphone is paired to a device, it will connect to the device automatically next time the

power is turned ON.

Deactivating ANC (Active Noise Cancelling) Function

Press and hold the ANC Button for 2 seconds and the ANC function will be deactivated in 2

different ways depending on the status of the headphone.

If the headphone power is ON: Announcement "OFF" will be emitted and the alternately flashing

blue and green light of the Bluetooth/ANC Status Indicator fades off.

If the headphone power is OFF: The green light of the Bluetooth/ANC Status Indicator fades off.

* The status of the ANC function when the headphone power is OFF can be easily recognizable by

refering to the Bluetooth/ANC Status Indicator.

Green light: ANC function ON

No light: ANC function OFF

6

To perform initial device pairing:

1. Press and hold the Power Button for 3 seconds and the headphones will turn ON with a "Power

ON" announcement. The headphones start device pairing mode automatically with the

Bluetooth/ ANC Status Indicator flashing alternately in red and blue.

2. With the Bluetooth function of the device being ON, choose "WHP01K" under the device list.

The device pairing is successful if "WHP01K Connected" is shown.

To reinitiate device pairing with another device:

1. While the headphone power is OFF, press and hold the Power Button for 5s and the

headphones will turn ON and start device pairing mode with "Power ON" & "Pairing"

announcements and the Bluetooth/ANC Status Indicator flashes alternately in red and blue.

2. With the Bluetooth function of the device is ON, choose "WHP01K" under the device list. The

device pairing is successful if "WHP01K Connected" is shown.

* It is necessary to unpair the current device pairing before reinitiating a new device pairing. This

can be done by removing the current connection or turning off the Bluetooth function of the

current paired device.

7

Performing Factory Reset

Media Control

If the headphone is having difficulty pairing to a device, please follow the simple steps below to

perform a factory reset.

1. While the headphone power is ON, press and hold the Volume + Button and the Volume -

Button simultenously for 2 seconds and the Bluetooth/ANC Status Indicator will flash twice in

purple together with 2 beeps.

2. The factory reset is completed. The headphones will start device pairing mode automatically

with the Bluetooth/ANC Status Indicator flashes alternately in red and blue.

Music Playback

Play

Pause

Next

Press the Power Button once

Press the Power Button once

Press and hold the Volume + Button for 2 seconds

Previous

Press and hold the Volume - Button for 2 seconds

Receiving Call

Press the Power Button once

Phone Call

End Call

Press the Power Button once

Declining Call

Press and hold the Power Button for 1second

Increasing Volume

Press the Volume + Button

Music Playback /

Phone Call

Siri/

Google Assistant

wired connection.

Activating

Press the Power Button twice *1

* 1: There is a possibility that this does not work for certain devices.

* Media controls on the headphones are disabled when the headphone is used with physical

Connecting the Headphones to a Device Using the Analog Audio Cable

Decreasing Volume

Press the Volume - Button

The headphones can be used with any device through physical wired connection by connecting

the headphones' 3.5mm Audio Jack to the device with the supplied analog audio cable. Once the

3.5mm Audio Jack is plugged in, the headphones will turn OFF immediately with all media controls

being disabled. Please perform media controls via the connected device instead.

* It is possible to activate the ANC fuction when the headphone is used with physical wired

connection.

* As the headphone power is OFF, no announcement of "Noise Cancelling" or "OFF" will be made

when the ANC function is activated or deactivated. Please refer to the Bluetooth/ANC Status

Indicator for the status of ANC function.

8

9

Important Safety Instruction

Trouble shooting : When you think, “Is it broken?”

· There is a risk of permanent hearing loss from extended use at excessive sound volumes. Please

do not exceed 40 hours use per week at a sound volume of 80 dB (A) or 5 hours per week at a

volume of 89 dB (A).

· To avoid electromagnetic interference, please refrain from use in places in which the use of

electronic devices is prohibited.

before using this product.

· If you are using a pacemaker or other electronic medical devices, please consult your physician

· This product contains small parts that may be hazardous to children, so please store in a place

that is out of the reach of children.

· Please do not subject to strong shocks or apply excessive force. Damage from abnormal use is

not covered by the warranty. To prevent damage, please store the earphones inside the case in

an appropriate location.

· Causing damage to the circuits may result in fire or electrical shock, so please do not attempt to

disassemble this product.

· Please keep this product away from water or other liquids that may cause shorts or other damage.

· Please do not attempt to repair this product yourself as unauthorized attempts at repair may

void the product warranty.

· Never use headphones when operating a bicycle, automobile, motorcycle or other motor vehicle

as this is a cause of traffic accidents and there is a risk of serious consequences. Even when

not driving, please do not use at railroad crossings, traffic intersections and other environments

where there is a danger in the inability to hear surrounding sounds.

· This product may be damaged if it is placed in locations where the environment is subject to

excessive direct sunlight, humidity, dust.

· A drastic change of air pressure inside the earcup could cause severe damage not only to

headphones but also to the ears. Please do not press the earcups when having the headphones on.

· Using headphones with earrings, piercings, or other jewelry on ears may cause injury. In

addition, they might cause degradation to the headphone performance or cause scratches to the

body of the headphones.

Problem

Cause

Remedy

( Immediately after

purchasing )

Battery charge is low

For safety of transportation from overseas, laws

and regulations do not allow the internal battery

to be fully charged at the time of shipping.

For that reason, voltage may fall below the level

required for operation at the time the customer

opens the package. Fully charging the battery

before use may relieve this inconvenience.

Please refer to “Charging the headphones” on

P. 4 regarding the method for charging.

Headphones will

not turn ON

Power Button has not

been pressed for

adequate time

Please press and hold the Power Button long

enough for the headphones to turn ON. Please

refer to "Powering ON" on P. 5 for the details of

the method.

ANC function has not

been deactivated and

caused battery level

depletion

Please make sure that the ANC function is

properly turned OFF when not in use since the

ANC function can be activated even when the

power is OFF. After using the headphones,

please turn OFF the ANC function on top of

powering OFF. Otherwise the battery may run out.

Analog Audio Cable

with 3.5mm Plug is

connected

Please disconnect the Analog Audio Cable

since the power is automatically turned OFF

once the Analog Audio cable is connected.

10

11

Trouble shooting : When you think, “Is it broken?”

Trouble shooting : When you think, “Is it broken?”

Problem

Cause

Remedy

Problem

Cause

Remedy

An error has occurred

due to improper

operation

Headphone power automatically turns OFF once

the analog audio cable is connected. Please try

to connect the cable and check if the

Bluetooth/ANC indicator is completely turned

OFF or turned into Green. Then please

disconnect the cable and check again if the

power can be turned ON/OFF. If the problem is

not solved, please perform the factory reset by

referring to "Performing Factory Reset" on P. 8.

Headphones

cannnot be

detected / paired

Headphones are not

in the pairing mode

In some cases, performing a reset operartion

may fix the problem. Please refer to "Performing

Factory Reset" on P. 8 for the method to reset

the headphones.

(Once pairing has been

performed) Connection

automatically established

with the previously

connected device

Please try performing the pairing operation

again after having deleted the pairing

information from a previously paired device.

Headphones will

not turn OFF

Power Button has not

been pressed for

adequate time

Please press and hold the Power Button long

enough for the headphones to turn OFF.

Please refer to "Powering OFF" on P. 5 for the

details of the method

ANC function has not

been deactivated

In case it takes

time to charge

The output of the USB

adapter being used

for charging is low

12

Please make sure that the ANC function is

properly turned OFF since the ANC function can

be activated even when the power is OFF. After

using the headphones, please turn OFF the ANC

function on top of powering OFF. Please refer to

"Deactivating ANC Function" on P. 6 for the

details of the method.

In case you are using the USB port on a PC,

etc., there are cases in which the output is low

and it may take more time to charge than the

time stated on the specification. As such please

use a 5V/1A USB adapter for charging this product.

Unstable music

playback

Interferance from

external factors

Bluetooth communicates using the 2.4GHz band

which might be interefered by other wireless

standards such as Wi-Fi, etc.

Moreover, the connection is sensitive against

liquid where humidity, rain, or even the size of

head could cause disruption to the connection.

The specifications of the device to be connected

could cause variation too.

For that reason, reducing the distance between

devices or switching OFF unused Wi-Fi/Bluetooth

of surrounding devices may improve the

connection.

Microphone

cannot be used

Analog Audio Cable

with 3.5mm Plug is

connected

As the power automatically turned OFF and the

microphone is disabled once the analog audio

cable is connected. Please disconnect the

analog audio cable.

13

Maintenance

Manufacturer:

Shenzhen Victory Flag Technology Co.,Ltd

Regularly wipe the headband and earpads with a soft, dry cloth to keep the headphones clean.

No.1 Xiangqian Lane Huangzhu Village,Pingdi Sub-district, Longgang district, Shenzhen,

Guangdong, China

* There is a possibility of a change in the specification, so please scan this QR code

for the latest user’ s manual.

Warranty and after service

The warranty for this product is valid for 1 year from the date of purchase. During the warranty

period, the product will be repaired based on the provisions below. The warranty is only valid

in the country in which the product was purchased. In the event that after-sales service or

support on the purchased product is needed, please contact and discuss with the store you

made the purchase from.  

1. During the warranty period, a malfunctioning product will be repaired free of charge if the

product is proven to fail even though it was used in accordance with the instructions in the

user's manual and the point of caution sections.

2. In the following cases, product repair will be subject to a fee even during the warranty period:

(1) The necessary documentation noted in the warranty card is not complete.

(2) The product is identified to be modified, disassembled, or repaired by a third party or

customer other than our company or our authorized organizations.

(3) The headphones were subjected to a strong impact or were allowed to get wet. Product

failure resulting from excessive use of force on the product.

(4) Failure of the product or damage caused as a result of fire, earthquake, storm or flood

damage, lightning strike, or other natural disasters.

9

(5) Repair of scratches on the surface of the housing or repair of the housing itself.

Earpads are considered as consumable parts which is not covered under warranty. If you wish

to purchase a new pair of earpads, kindly contact the store you made the purchase from.

Regarding the earpads:

14

T his card is necessary in the event that the warranty is utilized. Please store

this card along with a receipt or other documentation showing the date of purchase

in a safe place to be produced in the event that the warranty is utilized.

Please refer to the manual for the provisions of the warr anty.

15



 

 

 

 

 

 

 

 

 

 

 

 

 

 

final Inc. 3-12-7, Kitakase, Saiwai-ku, Kawasaki, Kanagawa, Japan 212-0057 Agent Authorization Company: final Inc. Address: 3-12-7, Kitakase, Saiwai-ku, Kawasaki, Kanagawa, Japan 212-0057 Product Name: Bluetooth Headphone Model Number(s): AG-WHP01K Product Description: Bluetooth Headphone We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: Jul. 16, 2021 Name:

Nakamichi Takashi Title:

Manager Company:

final Inc.

 

 

3-12-7, Kitakase, Saiwai-ku, Kawasaki, Kanagawa, Japan 212-0057

final Inc.

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Subject; Request for Confidentiality

FCC ID: 2AX2R-WHP01K

Date: July 16, 2021

To Whom It May Concern,

Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we

are requesting the Commission to withhold the following attachment(s) as confidential

documents from public disclosure indefinitely.

These documents contain detailed system and equipment descriptions and are considered as

proprietary information in operation of the equipment. The public disclosure of these documents

might be harmful to our company and would give competitors an unfair advantage in the market.

In additional to above mentioned documents, in order to comply with the marketing regulations

in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that

business sensitive information remains confidential until the actual marketing of newly

authorized devices, we request Short Term Confidentiality of the following attachment(s);

For 45 days, pursuant to Public Notice DA 04-1705.

OR

For 180 days pursuant to KDB 726920 D01.

It is our understanding that all measurement test reports, FCC ID label format and

correspondence during the certification review process cannot be granted as confidential

documents and this information will be available for public review once the grant of equipment

authorization is issued.

Schematic Diagram

Block Diagram

Operational Description

Parts List

Tune-up Procedure

External Photos

Test Setup Photos

Internal Photos

User Manual

Sincerely,

Signature:

Name: Nakamichi Takashi

Title: Manager