| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
Users Manual Draft | Users Manual | 2.03 MiB | January 10 2002 | |||
| 1 | Test Setup Photos | January 10 2002 | ||||||
| 1 | External Photos | January 10 2002 | ||||||
| 1 | ID Label/Location Info | January 10 2002 | ||||||
| 1 | Internal Photos | January 10 2002 | ||||||
| 1 | RF Exposure Info | January 10 2002 | ||||||
| 1 | Cover Letter(s) | January 10 2002 | ||||||
| 1 | Test Report | January 10 2002 |
| 1 | Users Manual Draft | Users Manual | 2.03 MiB | January 10 2002 |
FCC information FCC notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution CAUTION: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End user can not modify this transmitter device. Any unauthorized modification made on the device could avoid the user's authority to operate this device. IC (Industry Canada) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. The term IC: before the radio certification number only signifies that Industry Canada technical specifications were met. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
"The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canadas website www.hc-sc.gc.ca/rpb"
< Notice >
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End user can not modify this transmitter device. Any unauthorized modification made on the device could avoid the user's authority to operate this device. iPAD
(IPAD100-xx) Users Manual(Draft) C166-E324-01EN 1 Using the IPAD This manual contains important information required for using the iPAD safely. Before attempting to use the iPAD, read this manual carefully to ensure that you understand its contents. For safe operation of the product, pay particular attention to the section "Notes on Safety." Also keep this manual in a safe but convenient location for quick reference. Since Fujitsu takes every precaution to ensure that its products can be used safely without physical harm to users or damage to a product or peripheral equipment, use the iPAD only as instructed in this manual. 2 Preface Thank you for purchasing the iPAD. Before using the iPAD, read this manual thoroughly so that you will be able to take full of its functions. July 2002 First Edition VCCI Compatibility Standard This product is a Class A information technology device that complies with the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). Since use of the IPAD in a home environment can cause interference, appropriate protective measures may be required. Microsoft, Windows CE, and eMbedded Visual Tools are registered trademarks of Microsoft Corporation in the U.S.A. and/or other countries. Other company and product names appearing in this manual are the trademarks of their respective owners. 3 Using the iPAD in Mission-Critical Situations The iPAD is designed and manufactured for use in standard applications such as those for general office, personal, and household use. It is not intended for specialized uses, such as atomic energy control systems, aeronautical or space systems, mass transportation control systems, medical devices for life support, or weapons firing control systems where particularly high reliability requirements exist, the pertinent levels of safety are not guaranteed, or a failure or operational error could be life threatening or result in physical injury (referred to hereafter as
"mission-critical" use). Customers considering the use the iPAD for mission-critical applications must have safety-assurance measures in place beforehand, and should consult a Fujitsu sales representative before proceeding. 4 Warning Indications and Symbols This user's manual uses warning indications and symbols to help users use the iPAD safely and to prevent personal injury and property damage. This manual uses warning indications and symbols in the text to indicate safety conditions. The meaning of each indication and symbol is explained below. Warning Indications WARNING CAUTION Indicates a hazardous situation that could result in personal injury if the user does not perform the procedure correctly. Indicates a hazardous situation that could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also indicates that damage to the product or other property could occur if the user does not perform the procedure correctly. 5 Warning Symbols Indicates the possibility of injury from an electric shock. Indicates a condition that requires caution and a specific action that must not be performed. Indicates a condition that requires general caution. Indicates the possibility of an electric shock or fire. Indicates an action that is prohibited
(prohibited action). Indicates a required action. ELECTRIC SHOCK GENERAL INHIBITION GENERAL CAUTION FIRE DISASSEMBLY PROHIBITED UNPLUG THE CABLE 6 Notes on Safety WARNING ELECTRIC SHOCK GENERAL INHIBITION
Do not damage the power cord when you use the AC adapter, single-pack charger, or cradle. Doing so may result in an electric shock or fire.
Use only the specially designed cradle, AC adapter, and single-pack charger. If another item is used, differences in voltage or current can damage the iPAD.
If the battery is not handled correctly, the iPAD may overheat, explode, or catch fire. Be sure to observe the following precautions:
Neither throw the battery into a fire Connect the terminals correctly. Do not connect the terminals using a nor heat it. wire or other metallic material. Do not carry or store the battery while wearing a metal necklace or hair pin. Do not puncture the battery with a needle, hit it with a hammer, stamp on it, or otherwise apply a strong shock to it. Do not disassemble or modify the battery. 7 The laser scanner carried in this product complies with CDRH Class2 laser products. Read the following instructions, operating the scanner.
When using the laser scanner, do not direct the laser beam toward anyone's eyes. Doing so may injure the eyes.
Do not look into the aperture of the laser scanner. Because a laser beam is emitted from the aperture, you may injure your eyes. CAUTION: LASER 8 GENERAL INHIBITION FIRE DISASSEMBLY PROHIBITED WARNING Do not use or leave the battery near a flame, fire, stove, or other source of heat, in direct sunlight, or in a car exposed to sunlight. oven or other hot container. Do not put the battery in a microwave Charge the battery only on the special Do not charge the battery by directly cradle or single-pack charger. connecting it to a wall outlet or cigarette lighter in a car. Do not charge the battery near a flame or fire or under a hot sun.
If the iPAD generates heat, smoke, or an unusual smell or noise, turn off the power immediately and contact maintenance personnel. Failure to do so may result in an electric shock or fire.
Do not modify the iPAD without permission. Doing so may result in an electric shock or fire. 9 CAUTION
Turn off the iPAD before cleaning it.
Do not clean the iPAD using a damp or chemically treated cloth, and do not use thinner or other volatile chemical. Doing so may cause the iPAD to malfunction. GENERAL INHIBITION 10 GENERAL CAUTION
Do not remove the battery without turning off the iPAD.
Do not unplug the AC adapter or single-pack charger until charging has been completed. Doing do may cause the battery to be improperly charged.
Do not apply a strong shock to the iPAD. Do not drop the iPAD.
Although the iPAD is resistant to breakage for ordinary operations (for example, putting it on a desk), Fujitsu recommends that users use a neck strap so that the iPAD cannot be accidentally dropped.
Do not carry the iPAD do in your hip pocket. Sitting down with the iPAD in your hip pocket may break the display unit.
Because the fluorescent tubes in the liquid crystal display (LCD) used in the iPAD contain mercury, dispose of the LCD in accordance with any local laws and regulations.
Dispose of the main battery in accordance with any local laws and regulations after insulating the battery terminals with tape or other means to prevent a short circuit. 11
Always keep the magnetic card reader and magnetic cards clean. If dust, oil, or water gets on them, an error occurs or the magnetic head malfunctions or deteriorates.
Do not lubricate the magnetic card reader.
If you drop an object into the magnetic card reader slot, use tweezers or a similar means to extract it.
Keep magnetic cards and the magnetic card reader away from magnets or magnetic objects. Magnetism will destroy data on a magnetic card.
Always keep the IC card reader/writer and IC cards clean. If dust, oil, or water gets on them, an error occurs or the card reader/writer malfunctions or deteriorates.
Do not lubricate the IC card reader/writer.
(* Only the FWT31B2 accepts IC cards.)
Do not remove any component that is screwed on. Doing so may result in an electric shock, burns, or injury. GENERAL CAUTION DISASSEMBLY PROHIBITED 12 CAUTION
For safety reasons, unplug the AC adapter and single-pack charger if they will not be used for a long time. Failure to do so may result in an electric shock or fire. UNPLUG THE CABLE 13 Correctly Using the iPAD Using the main battery
To prevent deterioration, do not store the main battery for a long time when it is fully charged. For long-term storage, remove the battery from the IPAD when it is about 50% charged and store it at room temperature.
If the battery has not been used for a long time, recharge it.
Be careful not to short-circuit the battery terminals with a necklace or other metallic object.
Do not heat the battery or throw it into a fire.
Do not leave the battery in a car exposed to sunlight or in direct sunlight.
Do not allow the battery to become wet.
Do not apply a strong shock to the battery. Do not drop the battery. 14
Using the iPAD at low temperatures (below 10oC) At low temperatures (below 10oC), the iPAD does not operate as long as it does at room temperature. In an environment of 10oC, operating time is about 70% of that at room temperature, and in an environment of 0oC, it is about 50% (new battery used). If operation in a low-temperature environment is possible, review charging procedures and operation. In operation at low temperatures (below 10oC), replacing the battery with one that is only partially charged will result in a very short operating time. Be sure to replace the battery with a fully charged one. Keep a spare battery warm until you use it by, for example, putting it in your pocket. If you warm a battery with a body warmer, be careful that the battery does not come into direct contact with the body warmer.
If a message indicating that charging is required
(battery status message) is displayed, promptly charge the battery or replace the battery with a spare battery. 15
Be careful that no dust, sand, or other foreign matter enters the terminal section while you are using the iPAD. If any foreign matter gets in, completely remove it using a soft-tipped cotton swab or gauze, then repeat several times inserting the iPAD into the charger or device and then removing it.
The iPAD may not charge if the terminals are dirty.
Despite complete charging, the battery naturally discharges little by little as time passes. If possible, charge the battery again just before using it (within one or two days). Store the battery in as cool a place as possible and charge it at an ambient temperature of 10oC to 30oC. Doing so will increase the life of the battery. 16 Using the auxiliary battery
Auxiliary battery alarm message A warning message appears in the center of the screen if the voltage of the auxiliary battery drops or the auxiliary battery is not connected. The programs and data in memory will be lost if you replace the main battery while this message is displayed. Immediately charge the auxiliary battery.
>>Reference>> For information about charging the auxiliary battery, see Section 1.2.4, "Charging the auxiliary battery."
17 Long-term storage Store the iPAD where it will not be exposed to vibration, dust, high and low temperatures, high humidity, and direct sunlight.
Storing the iPAD with the programs saved To avoid discharging of the main and auxiliary batteries, charge the main battery once every week. Without charging, the programs and data in memory will be lost.
Storing the iPAD without the programs saved To store the iPAD without the programs saved, remove the main battery and completely reset the iPAD.
>>Reference>> For information about removing the battery, see Section 1.2.3,"
Installing and removing the main battery," and Section 1.2.4,
"Charging the auxiliary battery."
For information about completely resetting the iPAD, see Section 3.7.2, "Completely resetting the iPAD."
18 Cleaning
Clean the cover of the iPAD using a cloth moistened with a solution of water and neutral detergent and wrung out or a dry cloth. If you use a damp cloth, be sure to wring it out thoroughly to prevent water from getting into the iPAD, causing a malfunction. Do not wipe the iPAD using thinner, benzine, or other volatile solvent. Such materials can discolor the iPAD or erase printed characters.
Wipe the display area of theiPAD using a cloth moistened with water and wrung out thoroughly or a glass wipe with a very fine texture.
Occasionally clean the cradle interface using a dry cotton swab or gauze. If the terminals become dirty, contact may be poor, causing the IPAD to turn off or disabling normal charging and communication. 19 Other precautions
Do not disassemble or modify the iPAD.
To prevent the iPAD from malfunctioning, do not leave the iPAD, even for a short time, where it is exposed to any of the following conditions:
Extreme heat (for example, car in sunlight with the windows closed) Direct sunlight Extreme heat or cold Dust Strong vibration Humidity
Do not apply a strong shock to the iPAD. Do not drop the iPAD.
Be careful not to hold the iPAD for a long time in a high-temperature environment (35oC or higher). Doing so may result in a low-temperature burn. 20 Conventions Used in the Manual Symbols Symbol
Note
For reference
>>Reference>>
Circled numbers
(such as (1) and
(2))
Terminology Term Tap Double-tap Meaning Indicates a precaution or information you need to note. Be sure to read these items. Indicates useful information. Indicates a section to be referred to for more information. Indicates the steps, starting with (1), in a procedure. Indicates the result for an operation. Indicates the end of a series of operations. Meaning To press once somewhere on the screen of the IPAD To press twice in succession somewhere on the screen of the IPAD 21 22 Contents Preface ------------------------------------------- 3 Using the IPAD in Mission-Critical Situations ------------------------------------ 4 Warning Indications and Symbols------- 5 Warning Indications-------------------------------- 5 Warning Symbols----------------------------------- 6 Notes on Safety-------------------------------- 7 Correctly Using the IPAD -------------------------------------14 Using the main battery -------------------------- 14 Using the auxiliary battery---------------------- 17 Long-term storage-------------------------------- 18 Cleaning -------------------------------------------- 19 Other precautions -------------------------------- 20 Conventions Used in the Manual -------21 Symbols -------------------------------------------- 21 Terminology---------------------------------------- 21 Contents ----------------------------------------23 1 Before Using the IPAD -------------------------------------27 1.1 Names of Parts ----------------------------- 27 1.2 Using Batteries ----------------------------- 32 1.2.1 Batteries ----------------------------------32 1.2.2 Charging the main battery--------------34 1.2.3 Installing and removing the main battery-------------------------------------44 1.2.4 Charging the auxiliary battery ---------46 2 Setup -----------------------------------------47 3 Using the IPAD ------------------------------------------49 3.1 Turning the IPAD on and off------------- 49 3.1.1 Turning on the IPAD (resume mode)-49 23 3.1.2 Turning off the IPAD (suspend mode) 50 3.2 Checking the Battery Status------------- 51 3.3 Adjusting the Volume --------------------- 54 3.4 Adjusting the Brightness of the Front Light ------------------------------------------- 55 3.5 Correcting the Coordinates on the Touch Panel--------------------------------- 56 3.6 Using the Screen Keyboard ------------- 58 3.6.1 Displaying the screen keyboard -------58 Inputting a character --------------------58 3.6.2 3.6.3 Changing the keyboard type -----------59 3.7 Resetting the IPAD ------------------------ 61 3.7.1 Using the reset switch-------------------61 3.7.2 Completely resetting the IPAD --------62 4 LED Indications---------------------------64 4.1 IPAD LED ------------------------------------ 64 4.2 LED on the Single-Pack Charger during Charging ---------------------------- 66 5 Bluetooth------------------------------------67 6 Bar Code Scanner------------------------68 6.1 Using the Bar Code Scanner------------ 69 6.2 Bar Code Specifications------------------ 71 6.3 Cleaning the Reading Aperture of the Bar Code Scanner ------------------------- 71 6.4 Bar Code Sample Chart ------------------ 72 7 Using the Magnetic Card Reader----74 8 Using the IC Card Reader/Writer
(Installed in the FWT31B2) ------------76 9 User Action in Response to Messages -----------------------------------78 10 Troubleshooting --------------------------80 A Specifications -----------------------------82 B Consumables------------------------------84 C Accessories--------------------------------85 24 D Options --------------------------------------86 E Supplies -------------------------------------87 25 26 1 Before Using the IPAD 1.1 Names of Parts
<Front>
7 8 1 6 2 3 2 5 4 9 Part name 1 Magnetic card reader Reads magnetic cards. 2 Trigger key 3 Microphone (built-in) Used for speech input. 4 Operations section 5 Resistive-film touch Remarks Used when the barcode scanner is used. panel LCD LED 6 7 Wireless antenna
(built-in) 8 Bar code scanner See the <Operations section>. Referred to as "touch panel" or "screen" in this manual. Lit during charging on the cradle or during reading by the scanner. Can also be lit by an application. Used during 1 Mbps wireless communication. Outputs the laser beam used to read a bar code. 27
<Rear>
5 6 5 2 4 3 1 7 Part name Main battery compartment Speaker (built-in) Bar code scanner Wireless card Strap hole Reset switch Headset jack Remarks Holds a lithium ion battery
(main battery). Outputs sound. Outputs the laser beam used to read a bar code. A built-in 1 Mbps wireless device Means by which to attach a strap. Used to forcibly terminate or restart the unit.
* Do not use this switch during normal operation. Accepts a 2.5 mm diameter plug. NO. 1 2 3 4 5 6 7 28
<Bottom>
2 NO. 1 Part name Cradle interface 2 IC card reader/writer 1 Remarks Provides the contacts used to charge the iPAD or transfer data when it is mounted on the cradle
(IPAD142-01) Available only on the IPAD.100-20 Used to make a payment using an IC card. Insert an IC card with the IC terminal side facing up. For information about the cradle, see the "IPAD Cradle
(IPAD142-01)Manual 29
<Operations section>
1 2 11 8 12 7 6 5 3 4 9 10 NO. 1 2 3. 4 5 6 7 8 9 10 11 12 Part name Cursor key Function key 1 Function key 2 Clear key Shift key Enter key Cancel key Power key Numeric/charac ter keys
/ and .
(decimal point) keys Set key PIN LED 30 Remarks Moves the cursor. Invokes a function defined by an application. Invokes a function defined by an application.
[CLR] key in this manual.
[SFT] key in this manual.
[ENT] key in this manual.
[CAN] key in this manual.
Lights when a payment PIN is input.
<Operating style>
The iPAD is designed so that you can either hold it in one hand and operate it with your thumb or hold it in one hand and operate it with the other hand. The two styles shown in Figures 1 and 2. Operate the iPAD as shown in the figures.
[Figure 1]
[Figure 2]
<Using the neck strap>
31 1.2 Using Batteries 1.2.1 Batteries
Battery types The iPAD has a main battery and an auxiliary battery. Main battery: The main battery is used to back up the contents of memory during normal operation and in suspend mode. Auxiliary battery: The auxiliary battery is used to back up the contents of memory if the main battery loses its charge or the main battery is being replaced.
Guidelines on battery life
Main battery As a guideline, the life of the main battery is either about 500 chargings and dischargings or two years. The more a battery is used, the shorter the time it will last. The life of the main battery has expired if it loses its charge in a very short time after being fully charged. When this happens, replace the main battery with a new one. Main battery life may be less than 500 chargings and dischargings or two years depending on ambient temperature and how the iPAD is used.
Auxiliary battery The auxiliary battery is used temporarily to retain data while the main battery is being replaced. 32 The auxiliary battery backs up data in the iPAD's memory during replacement of the main battery. To replace the main battery, have ready a fully charged main battery and complete the procedure within ten minutes. The auxiliary battery is embedded in the main unit and cannot be replaced.
Message screen when recharging message displayed When the battery charge falls below a certain level, a message prompting you to recharge the battery appears.
Checking the battery status You can check the status of the battery status and the remaining battery charge.
>>Reference>> Section 3.2, "Checking the Battery Status"
33 1.2.2 Charging the main battery Charge the main battery the first time that you use it or when the battery charge is low. You can charge the main battery with any of the following methods:
Mounting the iPAD on the cradle with the main battery mounted in the iPAD
Using a single-pack charger
Connecting two cradles for simultaneous charging of two batteries
Connecting the single-pack charger and the cradle for simultaneous charging CAUTION
Do not unplug the AC adapter before charging has been completed.
Use only the cradle, AC adapter, and single-pack charger designed for the iPAD to prevent damage to the iPAD resulting from product differences such as voltage or current requirements.
Note
It is best to charge a battery at room temperature
(from 10oC to 30oC).
The cradle, AC adapter, or single-pack charger may become slightly hot. This is not a malfunction. For information about the single-pack charger, see the
"iPAD Single-pack Charger (CA05951-7080) User's Guide."
34
Charging the main battery using the cradle (IPAD142-01) You can use one of three methods to charge the main battery when you mount the iPAD on the cradle. The first method uses one cradle to charge one iPAD. The second method uses two cradles connected with a CA72001-1895 cable to charge two iPAD units simultaneously. The third method uses one cradle and one single-pack charger connected with a CA72001-1895 cable to simultaneously charge a battery and the iPAD.
<Using one cradle>
Using the cradle, you can charge one battery installed in the IPAD. A cradle (IPAD142-01) and an AC adapter
(CA05306-D500) are required for this operation.
(1) Connect the AC adapter to either of the cradle connection ports.
(2) Plug the AC adapter into a wall outlet. 35
(3) Turn off the iPAD.
(4) Insert the iPAD with the main battery installed into the cradle until you hear a click.
Charging starts. During charging, the LED is on and is orange. When charging is completed, the LED changes to green. The charging time is about 2.5 hours.
Note
Gently mount the iPAD on the cradle to prevent malfunctioning of the iPAD and cradle.
If the LED does not light, make sure that the IPAD is correctly mounted on the cradle. CAUTION
If you mount the iPAD on the cradle while iPAD power is on, the LED lights but the battery is not fully charged. This completes the operation. 36
<Using two cradles (IPAD142-01)>
Using two cradles, you can simultaneously charge two batteries, one on each of two iPAD units. Two cradles (IPAD142-01), one AC adapter
(CA05306-D500), and one cable (CA72001-1895) are required for this operation.
(1) Using a cable, connect the AC adapter connection interface on the right of one cradle to the connection interface on the left of the second cradle. The cable can be connected to either of the two AC adapter connection interfaces provided on a cradle.
(2) Connect an AC adapter to the unoccupied AC adapter connection interface on either of the cradles.
(3) Plug the AC cable of the AC adapter into a wall outlet. 37
(4) Turn off the iPAD.
(5) Insert the iPAD units with the their main batteries installed into the cradles until you hear a click.
Charging starts. During charging, the LED is on and is orange. When charging is completed, the LED changes to green. The charging time is about 2.5 hours.
Note
Gently mount the iPAD on the cradle to prevent malfunctioning of the iPAD and cradle.
If the LED does not light, make sure that the iPAD is correctly mounted on the cradle. CAUTION
If you mount the iPAD on the cradle while iPAD power is on, the LED lights but the battery is not fully charged. This completes the operation. 38
<Removing the iPAD from a cradle>
Remove the iPAD from the cradle as follows: Lightly hold the iPAD with one hand. Using the other hand, press the Eject button in the center of the cradle. When the iPAD is released from the cradle, hold it lightly and lift it. Eject button 39
Charging the main battery using a single-pack charger (CA05951-7080) You can charge the main battery using a single-pack charger (CA05951-7080). Charging using this method requires a single-pack charger (CA05951-7080) and an AC adapter
(CAS05306-D500).
(1) Connect the AC adapter to the single-pack charger.
(2) Connect the AC adapter to the single-pack charger.
(3) Plug the AC cable of the AC adapter into a wall outlet.
(4) Mount the main battery on the single-pack charger.
Charging starts. During charging, the pack charger LED is on and is orange. When charging is completed, the LED changes to green. The charging time is about 2.5 hours.
Note
If the pack charger LED lights in red, the battery is faulty and cannot be charged. Replace the battery. 40 CAUTION
The LED will not light if the main battery is not correctly installed. This completes the operation. 41
<Using a single-pack charger (CA05951-7080) and a cradle (IPAD142-01) that are connected>
You can simultaneously charge main batteries mounted on a single-pack charger and in the IPAD mounted on a cradle. A single-pack charger (CA05951-7080), cradle
(IPAD142-01), AC adapter (FHTAC601A), and cable
(CA72001-1895) are required for this operation.
(1) Using the cable, connect the AC adapter connection interface of the single-pack charger to either the left or right AC adapter connection interface on the cradle. The cable can be connected to either of the two AC adapter connection interfaces provided on the cradle.
(2) Connect the AC adapter to the unused AC adapter connection interface on the cradle. 42
(3) Plug the AC cable of the AC adapter into a wall outlet.
(4) Turn off the iPAD.
(5) Insert the iPAD with the main battery installed into the cradle until you hear a click.
Charging starts. During charging, the LED is on and is orange. When charging is completed, the LED changes to green. The charging time for the two is about 2.5 hours.
Note
Gently mount the iPAD on the cradle to prevent malfunctioning of the iPAD and cradle.
If the LED does not light, make sure that the iPAD is correctly mounted on the cradle. CAUTION
If you mount the iPAD on the cradle while IPAD power is on, the LED lights but the battery is not fully charged.
The LED will not light if the main battery is not correctly mounted on a single-pack charger. This completes the operation. 43 1.2.3 Installing and removing the main battery
Installing the main battery
(1) On the rear of the iPAD, slide the battery lock switches on both sides of the lower part to the outside.
(2) Slide down the battery cover to remove it.
(3) Insert the main battery in the battery compartment. In this step, make sure the black ribbon is outside.
(4) Install the battery cover and slide it upward to lock it. In this step, make sure that the black ribbon does not protrude from the cover.
(5) Slide inward the battery lock switches to lock them. CAUTION The iPAD can be turned on only when the battery lock switches have locked. This completes the operation. 44
Removing the main battery
(1) Turn off the iPAD.
(2) On the rear of the iPAD, slide the battery lock switches on both sides of the lower part to the outside.
(3) Slide down the cover to remove it.
(4) Pull the black ribbon to remove the battery. CAUTION
Be sure to turn off the iPAD before replacing the main battery.
Make sure that the auxiliary battery has sufficient charge before replacing the main battery. The data in memory may be lost if you replace the main battery while the auxiliary battery alarm message is displayed.
While the main battery is being replaced, the auxiliary battery backs up data in the iPAD memory. When replacing the main battery, have ready a fully charged main battery and complete the procedure within ten minutes. The life of the auxiliary battery is significantly reduced if the iPAD is left with the main battery removed. This completes the operation. 45 1.2.4 Charging the auxiliary battery
Charging the auxiliary battery Charge the auxiliary battery by installing a sufficiently charged main battery in the iPAD. For initial installation, charge the auxiliary battery at least 24 hours, since its voltage is low. Initially, the auxiliary battery will start to charge once the iPAD has been turned on. (During normal operation, the auxiliary battery is permanently charged as long as the main battery is installed.) Even though the auxiliary battery is charged, notify your maintenance representative if an alarm is frequently displayed. CAUTION
The auxiliary battery is temporarily used to retain data while the main battery is being replaced. The life of the auxiliary battery may be shortened if the iPAD is left with only the auxiliary battery installed.
Do not leave the iPAD in a state with the main battery removed.
For Reference The following are the guidelines for the retention of dat a in memory while the iPAD is off (suspend mode):
If both the main and auxiliary batteries are fully charged: About 1 month
If the main battery is in the alarm state and the auxiliary battery is fully charged: About 3 days The usage environment may affect these estimates. 46 2 Setup After the iPAD has been removed from its packaging, set it up.
(1) When you turn on the iPAD for the first time, the initial installation screen shown below appears. To start the setup process, press the [CAN]
key while holding down the [SFT] key. Is this the initial installation?
(2) The touch panel correction screen appears. Follow the instructions on the screen.
>>Reference>> Section 3.5, "Correcting the Coordinates on the Touch Panel"
(3) Date/Time Properties is activated. For information about Date/Time Properties, see the "iPAD (IPAD100-xx) Software Operator's Guide."
(4) After Date/Time Properties has been set, the setup tool program is activated. When
" Bringing up the Setup Tool Menu" is displayed, install the applications. 47 For information about installing an application, see the "iPAD (IPAD100-xx) Software Operator's Guide."
CAUTION
The iPAD is not shipped with the main battery installed and charged. Perform setup either with the iPAD connected to the cradle or after you have charged the main battery and installed it in the iPAD.
>>Reference>> Section 1.2, "Using the Battery"
The auxiliary battery is installed in the iPAD, but it has not been charged. To charge the auxiliary battery, install a charged main battery in the iPAD.
>>Reference>> Section 1.2.4, "Charging the auxiliary battery"
48 3 Using the iPAD 3.1 Turning the iPAD on and off 3.1.1 Turning on the iPAD (resume mode) With the power off, press the Power key until the LED lights in green.
The iPAD is turned on, the screen light, and the LED goes off.
Turning on the iPAD for the first time:
The initial installation screen appears when you turn on the iPAD for the first time or you initialize the system. See the "iPAD (IPAD100-xx) Software Operator's Guide" for information about performing setup.
Turning on the iPAD after the first time:
The screen that was displayed when you stopped the last time is displayed. CAUTION
During resume processing (the green LED is on), do not remove the main battery or press the Reset button. Either of these actions may cause the data in memory to be lost. 49 3.1.2 Turning off the iPAD (suspend mode) With the power on, press the Power key.
The screen turns black and the iPAD is turned off. CAUTION
Do not unlock and remove the main battery from the iPAD until power has been turned off. Doing so may cause the data in memory to be lost.
Do not turn off the iPAD in the following state:
Data is being backed up or restored.
(The hourglass icon is displayed.)
For Reference You can also turn off the iPAD as follows:
Tap the [Start] button, then the [Suspend] button.
When power is on, the iPAD has a function that automatically turns itself off if no action is performed for a certain length of time (automatic power-off function). For more information, see the "iPAD (IPAD100-xx) Software Operator's Guide."
An application may prevent power from being turned off while the iPAD is operating. If you are using such an application, turn off the iPAD with an instruction from the application. 50 3.2 Checking the Battery Status You can check the battery status. While the iPAD is on, press the [ENT] key while holding down the [SFT] key. The [System Information] window opens. System Information Battery information Main battery Status: External power source Remaining charge Auxiliary battery Status : Normal 1. Volume and brightness settings 2. Touch panel correction Battery voltage: 3.87 V Check the battery status in [Battery Information]. The items in [Battery Information] have the following meanings:
51
Main battery
Status External power source Indicates that the iPAD is mounted on the cradle. Normal Indicates that the battery can be used. Insufficient charge Indicates that the main battery charge is too low. Either charge or replace the main battery.
Remaining battery charge The current main battery charge is shown as one of five levels.
Note
If [Insufficient charge] is displayed, the remaining battery charge is too low. Either charge the battery or replace it with a spare battery.
If the charge is too low, a message is displayed on the screen and the iPAD is automatically turned off after a while. Either charge or replace the battery. After checking the battery status, tap the [] button on the window to close it. This completes the operation. 52
Auxiliary battery
Status Indicates the auxiliary battery status. The displayed status is one of the following:
Normal Indicates that memory backup is allowed. Insufficient charge Indicates that the charge is not sufficient for memory backup. Charge the battery.
Note
If [Insufficient charge] is displayed, the auxiliary battery charge is too low. Charge the auxiliary battery. After checking the battery status, tap the [] button on the window to close it. This completes the operation. CAUTION
The data in memory may be lost if you remove the main battery while the auxiliary battery has an insufficient charge.
>>Reference>> For information about charging the auxiliary battery, see Section 1.2.4, "Charging the auxiliary battery."
53 3.3 Adjusting the Volume While the iPAD is on, press the [ENT] key while holding down the [SFT] key to bring up the [System Information] window. Next, tap [1. Volume and brightness settings]. Volume and Brightness Volume Low High Front light OFF Dark Bright
The [Volume and Brightness] window opens.
(1) In the [Volume] area, adjust the speaker volume.
(2) Tap the and buttons to adjust
the volume. The order of choices from the left is low, somewhat low, somewhat high, and high.
(3) Tap the [] button on the window to close it. This completes the operation. 54 3.4 Adjusting the Brightness of the Front Light While the iPAD is on, press the [ENT] key while holding down the [SFT] key to bring up the [System Information] window. Next, tap [1. Volume and brightness settings]. Volume and Brightness Volume Low High Front light OFF Dark Bright
(1) In the [Front light] area, specify the
brightness. Tap the and buttons to select the brightness level. The order of choices from the left is off, somewhat dark, somewhat bright, and bright.
(2) Tap the [] button on the window to close it. This completes the operation.
For Reference
The front light automatically goes off if the remaining battery charge is too low. 55 3.5 Correcting the Coordinates on the Touch Panel The coordinates on the touch panel are misaligned if the touch panel does not respond when you tap the screen or a location different from where you tapped is entered. If this situation occurs, correct the misaligned coordinates on the touch panel. This operation is called "touch panel correction."
Perform touch panel correction as follows: While the IPAD is on, press the [ENT] key while holding down the [SFT] key to bring up the [System Information]
window. Next, tap [2. Touch panel correction] key on the screen or press the [2] key to bring up the following touch panel correction screen. Use the stylus to press the center of the crosshairs for about one second. Lift the stylus and the crosshairs will move. Repeat the same procedure. To cancel this operation, press the [SFT] and [CLR] keys. 56
(1) As directed on the screen, tap the center of the crosshairs (+) using a stylus. You will need to tap the center and the four corners of the screen.
(2) After you have tapped all the correct locations, the crosshairs disappear and the message "New correction settings made" is displayed. Press the [ENT] key to register the correction settings. To cancel the operation, press the [CLR] key while holding down the [SFT] key.
Note
If you tap a location away from the crosshairs, you will be required to start the operation again from the beginning.
Do not press the Power key while the touch panel correction tool is running. Doing so will nullify the touch panel correction settings, and the touch panel correction will have to be done again.
If the battery loses its charge during touch panel correction, charge or replace the battery, then perform touch panel correction again.
Use a stylus. Do not tap the screen with a pencil, ballpoint pen, or any other pointed object. Doing so may scratch or crack the screen.
Do not touch the screen with your palm while you are tapping the screen. This completes the operation. 57 3.6 Using the Screen Keyboard The screen keyboard is the keyboard that is displayedon the screen. 3.6.1 Displaying the screen keyboard Open and close the screen keyboard as follows:
(1) To open the screen keyboard, press the [0]
key while holding down the [SFT] key. The screen keyboard appears on the lower part of the screen.
(2) To close the screen keyboard, press the [0]
key while holding down the [SFT] key, as you did to open it. The screen keyboard disappears from the lower part of the screen. This completes the operation. 3.6.2 Inputting a character To input a character, tap the input field to make it ready for input (the cursor is displayed). When the field is ready for input, tap a character on the screen keyboard. The character is entered in the input field. This completes the operation. 58 3.6.3 Changing the keyboard type There are three types of screen keyboard: keyboard
(Figure 1), extended keyboard (Figure 2), and handwriting (Figure 3).
(Figure 1)
(Figure 2) Em/en Kata kana Sym-
bol Hira gana
(Figure 3) Handwriting Back space Enter Space Em-size Number Recog-
nize Space Convert 59 You can change the keyboard type as follows:
(1) Double-tap the [Input Panel] icon in [Control Panel].
(2) When [Input Panel Properties] is displayed, select a keyboard type in [Current Input Method].
(3) Tap the [OK] button. CAUTION
The setting will not change if you close the screen by tapping the [] button instead of using the [OK] button. This completes the operation. 60 3.7 Resetting the iPAD 3.7.1 Using the reset switch Use the reset switch mainly to install an application or driver or change a setting.
(1) If possible, save the data that you are working on.
(2) Using a stylus, press the reset switch located on the left side of the rear of the iPAD.
(3) The screen turns black, then the power is turned on again. CAUTION
If you reset the iPAD, any unsaved data or settings are lost.
Do not use the reset switch while the iPAD is in operation (saving data or resuming operation). Doing so may cause data in memory to be lost. This completes the operation. 61 3.7.2 Completely resetting the iPAD Completely reset the iPAD if it is not operating correctly after a reset or if you want to prevent deterioration of the main battery when storing the iPAD for a long period.
(1) Turn off the iPAD
(2) On the rear of the iPAD, slide the battery lock switches on both sides of the lower part to the outside.
(3) Slide down the cover to remove it.
(4) Pull the black ribbon to remove the battery.
(5) Using the stylus, press the switch exposed when the battery is removed.
All the data in memory is cleared, and memory is initialized. 62 CAUTION
When you completely reset the iPAD, all of the data and information (Control Panel settings and installed applications) in its memory is lost
(except for the data in the flash disk area). See the "iPAD (IPAD100-xx) Software Operator's Guide" to restore the applications. This completes the operation. 63 4 LED Indications This chapter explains the indications of the LED on the IPAD and on the single-pack charger. 4.1 iPAD LED LED indication Indication Lights and then goes off. Explanation The iPAD is starting up
(resuming operation). Do not operate the iPAD until the LED goes off. Lights if the bar code is read correctly. The iPAD is in scanner reading processing mode. Do not operate the iPAD until the LED goes off. Lights if the magnetic card is read correctly.
(*1) Lights. The LED can be made to light if the iPAD reads the magnetic card correctly. The battery is being charged. The LED turns green when charging is complete. C o l o r G r e e n G r e e n G r e e n O r a n g e Equipment status iPAD is being turned on Bar code is being read by the scanner Magnetic card being read by the reader Battery on the cradle is being charged 64 Equipment status Battery on the cradle is being charged
(*1) LED indication Lights. Indication Explanation Charging is complete. C o l o r G r e e n Y e l l o w The LED can be made to go on by an application when a magnetic card is read by the reader. A charging error has occurred. Either replace or charge the main battery again. Lights. 65 4.2 LED on the Single-Pack Charger during Charging LED indication Indication Meaning Lights. The battery is being charged. Lights. Charging is complete. Lights. The main battery cannot be charged because it either is not correctly connected to the single-pack charger or is faulty. Either correctly connect the main battery to the single-pack charger or replace the main battery. C o l o r O r a n g e G r e e n R e d 66 5 Bluetooth The iPAD can communicate with a server when used together with a bluetooth base station. The wireless communication system used is spread-spectrum communication that uses the 2.4 GHz band. This system does not require a license for wireless communications. In a store environment, the iPAD can communicate within a radius of 5 to 20 m from the base station.
(The range of communication that is possibly varies significantly depending on the environment. In a semi-open space, communication is up to 30 to 50 m.) CAUTION
The iPAD may not be able to communicate if it is used near a microwave oven, security gate, or other device that generates noise.
Use the iPAD away from a TV set, radio, or another wireless device. 67 6 Bar Code Scanner Reading aperture of bar code scanner 68 6.1 Using the Bar Code Scanner
(1) Aim the bar code scanner of the iPAD at a bar code.
(2) Press either of the trigger switches on the two sides of the iPAD. A scanning beam passes through the reading aperture of the bar code scanner.
(3) Run the scanning beam across the bar code.
(4) The LED lights in green if the data has been read correctly.
(5) The scanning beam automatically stops when reading is completed.
(6) Release the trigger switch. 69 WARNING
Do not look into the reading aperture while a scanning beam is being emitted. Doing so can injure the eyes.
For Reference
A scanning beam stops in about one second if you continue to press the trigger key but no bar code is detected from the reading aperture.
If a bar code cannot be read, try changing the direction of the scanning beam in relation to the bar code or the distance of the IPAD from the barcode. Note that if the scanning beam passes over more than one bar code, it cannot be determined which of the bar codes will be read. 70 6.2 Bar Code Specifications Item PCS value Specifications 0.25 or more (Value for a 650 nm laser Resolution Reading angle Vertical direction: 65o or less 0.13 mm beam) Distance Horizontal direction: 60o or less Rotation: 30o or less Narrow bar width 0.13 mm 0.19 mm 0.25 mm 0.33 mm 0.51 mm 1.02 mm 1.40 mm LED indication (green) 5.6 to 12.7 cm 4.6 to 19.0 cm 5.08 to 24.6 cm 5.08 to 30.4 cm
* to 38.1 cm
* to 55.8 cm
* to 73.6 cm Reading depth Reading confirmed by:
* The minimum reading distance is determined by the bar code label width and the reading depth. 6.3 Cleaning the Reading Aperture of the Bar Code Scanner The reading aperture of the bar code reader must always be clean when it is used. Clean the reading aperture using a dry cloth or a cloth moistened with water or a diluted neutral detergent solution. Do not use alcohol, thinner, or other volatile solvent. 71 6.4 Bar Code Sample Chart Use the sample chart to check whether the scanner is faulty. NW7 Code 39 JAN standard JAN abbreviated UPC/E 72 UPC/A Code 128 InterLeaved2of5 EAN-8 EAN-13 CAUTION
This chart may become illegible due to age or improper handling of the User's Manual. 73 7 Using the Magnetic Card Reader
(1) After making sure of the orientation
(direction of the arrow, for example), insert a magnetic card.
(2) Slowly move the magnetic card from left to right.
Note
A magnetic card will not be read correctly if movement stops part way, the speed of movement changes, or the card is not moved parallel with the slot.
The LED can be made to light by an application when a magnetic card is read correctly. 74
<Cleaning the magnetic card reader>
The magnetic card reader becomes contaminated with dirt and dust from use. Clean the reader using the cleaning card supplied as an accessory. Cleaning cycle: Clean the reader every month or whenever errors are frequent. Cleaning method: Insert the cleaning card
(supplied) in the reader with the rough side
(cleaning side) facing up. (Insertion is the same as for a magnetic card.) Replacement cycle: Replace the cleaning card
(supplied at a cost) when it becomes contaminated. If errors still occur after the reader has been cleaned, notify your Fujitsu maintenance representative. CAUTION
Before cleaning the reader, turn off the IPAD to guard against a possible malfunction. 75 8 Using the IC Card Reader/Writer
(Installed in the IPAD100-20) Figure 1 IC card slot The IPAD100-20 iPAD is equipped with an IC card reader.
(1) When instructed to by message, insert an IC card in the IC card slot with the IC terminal side facing up. Figure 2 76
<Cleaning the IC card reader/writer>
The contacts of the IC card reader/writer become contaminated with dirt and dust from use. Clean the reader using the cleaning card supplied as an accessory. Cleaning cycle: Clean the reader every month or whenever errors are frequent. Cleaning method: Insert the cleaning card in the reader with the rough side
(cleaning side) facing up.
(Insertion is the same as for an IC card.) Replacement cycle: Replace the cleaning card
(supplied at a cost) when it becomes contaminated. If errors still occur after the reader has been cleaned, notify your Fujitsu maintenance representative. CAUTION
Before cleaning the reader, turn off the iPAD to guard against a possible malfunction. 77 9 User Action in Response to Messages If any of the following messages is displayed, take the action described in the following table. Message Main battery alarm The front light is off. Cause The main battery charge is too low. User response Either replace the main battery or charge the main battery using the battery charger or cradle.
>>Reference>>
Section 1.2.2,
"Charging the main battery"
Section 1.2.3,
"Installing and removing the main battery"
Charge the auxiliary battery.
>>Reference>>
Section 1.2.4,
"Charging the auxiliary battery"
Press the [SFT] and
[CAN] keys simultaneously to install application programs.
>>Reference>>
"IPAD
(FWT31Bx) Software Operator's Guide"
Auxiliary battery alarm Is this the initial installation?
The auxiliary battery charge is too low. No application programs have been installed. 78 Message A power failure may have occurred. An error was detected on the flash disk. Cause The memory data was deleted because, for example, the battery charge was too low. An error occurred in the system information storage area of the flash ROM. User response Press the [SFT] and
[CAN] keys simultaneously to automatically recover the application programs.
>>Reference>>
"iPAD
(IPAD100-xx) Software Operator's Guide"
Tap the [OK] button to initialize the flash ROM and then reinstall the application programs.
>>Reference>>
"iPAD(IPAD100-x x Operator's Guide"
79 10 Troubleshooting If you encounter any of the problems described in the following table while using the IPAD, take the indicated action before notifying your maintenance representative. Problem The IPAD cannot be turned on. User response The main battery has no charge. Replace it with a charged main battery.
>>Reference>>
Section 1.2, "Using the Battery"
Alternatively, charge the main battery.
>>Reference>>
Section 1.2.2, "Charging the main battery"
If the main battery is completely dead, all the data and information in memory in the IPAD may be lost. If data has been lost, reinstall the applications again.
>>Reference>>
"IPAD (FWT31Bx) Software Operator's Guide"
The service life of the main battery has expired or the battery is faulty. Install a new main battery.
>>Reference>>
Section 1.2, "Using the Battery"
80 Problem TheiPAD cannot be turned on.
(continued) The screen appears for a moment, then turns black when you press the Power key to turn on the power. The speaker is silent. The touch panel does not respond. The front light is dark or turns black. User response The main battery may not be correctly installed. Install the main battery correctly.
>>Reference>>
Section 1.2.3," Installing and removing the main battery"
The battery lock switch may be unlocked.
>>Reference>>
Section 3.7.2,
"Completely resetting the iPA The main battery may have no charge. Replace it with a charged main battery.
>>Reference>>
Section 1.2, "Using the Battery"
The speaker may be set to
"Low." Check the volume setting of the speaker.
>>Reference>>
Section 3.3," Adjusting the Volume"
The coordinates on the touch panel may be misaligned. Perform touch panel correction.
>>Reference>>
Section 3.5, "Correcting the Coordinates on the Touch Panel"
The main battery may have no charge. Replace it with a charged main battery.
>>Reference>>
Section 1.2, "Using the Battery"
81 A Specifications Control section Item CPU Memory Specification 32-bit RISC CPU ROM: 32 MB RAM: 64 MB Flash disk: 32 MB WindowsCE.NET Display section OS Display type 3.5-inch TFT reflective color LCD Resolution 240 pixels wide by 320 pixels high
(with 2D acceleration) High-intensity front light Display lighting Operations section Touch panel (resistive-film type), trigger switches (bar code scanner input), power key, function keys, set key, cursor keys, clear key, numeric keypad, key, / key, decimal-point (.) key, cancel key, enter key, shift key, and cellular phone input mode
(alphabetic/hiragana input) Cradle I/F: USB client
(for PC connection) Charge terminals JAN/EAN-13/8, UPC-A/E, NW-7, CODE39/128, Interleaved2of5
(ITF) Speaker 1 built-in, microphone 1 built-in, headset connector (input/output) JIS I(ISO1/2), JIS II Applicable card: ISO/IEC7816 SSFH wireless: Bluetooth V1.1 compliant, 1 Mbps (Symbol Rate), built-in antenna External interface Scanner Audio Magnetic card reader IC card reader/writer
(FWT31B2 only) Communications 82 Power source Item Specification Main battery Lithium ion battery for Auxiliary battery Operating time Charging Humidity FWT3xxx 1700mAh/3.7V Manganese dioxide lithium battery About 7 hours
(new battery, room temperature, wireless communication in progress for 10% of the time, and front light off) About 3 hours
(new battery, room temperature, wireless communication in progress for 10% of the time, scanner reading once every ten seconds, and front light on at the
"dark" setting) About 2.5 hours
(single-pack charger) About 2.5 hours
(cradle with the iPAD turned off)
(no condensation) Storage: -20 to 60oC
(no condensation) Operating: 20 to 85%
(no condensation) Storage: 8 to 95%
(no condensation) 84(W) 187(D) 23(H) mm
(protrusions excluded ) About 340 g
(including main battery) Temperature Operating: 0 to 40oC Ambient conditions Dimensions Weight 83 B Consumables The following table lists the consumables that the user must replace. Service life Product name Product number 0644040 About 500 chargings and dischargings, or about two years Lithium ion battery for FWT3xxx
(Main battery) The main battery service life may be less than about 500 chargings and dischargings or two years depending on the ambient temperature and how the iPAD is used. If the main battery requires two cycles of charging and discharge per day, service life is less than one year. If you use the iPAD in a manner that is not standard use as specified by Fujitsu, components other than the consumables listed above may have to be replaced at the user's expense. For more information about standard use and components that may have to be replaced, consult your maintenance representative. 84 C Accessories Item
* Lithium ion battery for FWT3xxx
* Strap with a stylus pen
* Cleaning card Drip-proof cover (for magnetic card reader) User's manual Quantity 1 1 1 1 1 (this manual)
* Supplies that can be purchased are the lithium ion battery for the FWT3XXX, strap with a stylus pen, and cleaning card (product name: Magnetic Card Reader Cleaning Card). 85 D Options Product name Cradle Model IPAD142-01 Single-pack charger CA05951-7080 AC adapter FHTAC601B USB cable CA 86 Specification overview Special cradle for the IPAD100-xxCA5306-D 500 Unit that accommodates the IPAD to recharge its battery. The charging time is about 3 hours. An AC adapter) is required for each cradle. IPAD100-xxCA5306
-D500 An AC adapter
(FHTAC601A) and a cable (CA72001-1895) are required for two cradles. Unit that itself charges a square-type lithium ion battery. An AC adapter
(FHTAC601A) is required for the charger. The charging time is about 2.5 hours. AC adapter required to use a cradle two cradles or connects a cradle and a single-pack charger Cable that connects the IPAD to a PC while the IPAD is in the cradle Cable CA72001-1895 Cable that connects E Supplies For supplies, use authentic Fujitsu CoWorCo brand name products appropriate for the iPAD. The use of other supplies will shorten the life of IPAD parts or cause the IPAD to malfunction. Item Lithium ion battery for FWT3xxx Cleaning cloth for touch panel Product code 0644040 0632320 Shipping unit 1 5 0631310 1 set 0631312 1 set 0631313 1 set Magnetic card reader cleaning card *
Magnetic card reader cleaning card (2) *
Double-sided cleaning card for magnetic card reader *
Remarks For the touch panel and the bar code reader Single-side d type with a case;
10 cards per set Single-side d type;
10 cards per set Double-side d type;
2 cards per set
* Head cleaning cards that can be used for both the magnetic card reader and the IC card reader/writer. If either of these cards is used, the life of the head and cards can be extended. 87
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2002-10-01 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2002-10-01
|
||||
| 1 | Applicant's complete, legal business name |
Fujitsu Limited
|
||||
| 1 | FCC Registration Number (FRN) |
0006180137
|
||||
| 1 | Physical Address |
Marunouchi Center Bldg.
|
||||
| 1 |
Chiyoda-ku Tokyo 100, N/A
|
|||||
| 1 |
Japan
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
m******@ccsemc.com
|
||||
| 1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
C9S
|
||||
| 1 | Equipment Product Code |
DTA01IPAD100
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
T****** M******
|
||||
| 1 | Title |
Project Manager
|
||||
| 1 | Telephone Number |
N/A********
|
||||
| 1 | Fax Number |
N/A********
|
||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Handheld Bar-code Reader | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Output power listed is conducted. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with specific operating instructions for satisfying RF exposure compliance. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Japan Quality Assurance Org.
|
||||
| 1 | Name |
T****** K****
|
||||
| 1 | Telephone Number |
81-(0********
|
||||
| 1 | Fax Number |
81-(0********
|
||||
| 1 |
@******@.
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0140000 | ||||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC