GE Lighting Solutions 1975 Noble Rd. Cleveland, OH 44112 UltraMaxTM Connected LED Driver Installation Guide GED80MCC/Z2P1500 BEFORE YOU BEGIN: Please read these instructions completely and carefully Only Qualified Electricians Should Perform the Installation of this LED Driver This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005(A). Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment (GED80MCC/Z2P1500) contains the limited module with FCC ID PUU80MCCZ2P15 and ISED ID 10798A-80MCCZ2P15. This equipment complies with FCC CFR 47 Part 2 requirements for radiation exposure for fixed facility or mobile applications that maintain a distance of 20 cm from a persons body. This equipment complies with ISED RSS-102 Issue 5 requirements for radiation exposure limits for an uncontrolled environment that maintain a distance of 20 cm from a persons body. This radio transmitter ISED ID 10798A-80MCCZ2P15 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Only the following antennas should be used with this limited module and the antenna should only be installed when the host product is manufactured. (The antenna is not field replaceable.) PulseLARSEN W3357 (50 impedance; peak gain over 2400 2483.5 MHz range is 0.4dBi) Walsin RFPCA430618IMAB301 (50 impedance; peak gain over 2400 2483.5 MHz range is 2.2dBi) You must follow these codes and safety standards when installing this product:
-National Electric Code (NEC)
-Applicable Federal, Standard and Local Electric Codes
-U.L. safety standards. Failure to comply with these codes and standards may cause death, serious injury, and property damage. Before installing this driver:
1. Remove Power from fixture by switching circuit breaker powering the fixture to the off position. a. Caution: Turning off the fixtures wall switch may not remove voltage from fixture. 2. For maximum safety, fixture must be grounded. Make sure fixture is properly grounded with a green ground wire per National Electrical Code (NEC). 3. Verify that driver is the correct driver for the fixture, input voltage, and application. During installation:
1. Follow all relevant National Electric Code (NEC), Federal, State and Local Electric Codes as well as U.L. safety standards. 2. Access and open driver compartment cover. 3. Remove old driver and any extra wires from enclosure. 4. Inspect and replace any damaged or deteriorated cable. 5. Review the wiring diagram on the new driver label (figure below) and identify connections to be made. 6. Install the new driver and make sure the new driver is properly grounded to metal fixture per National Electrical Code (NEC). Tighten driver mounting screws seating driver firmly against fixture surface. To insure electrical grounding between driver case and fixture housing mounting screws with star washers are recommended to break (penetrate) the painted surface of the driver mounting foot. 7. Install the antenna within the fixture enclosure (away from grounded metal surfaces when possible). The antenna shall not be cut or have any insulation material removed or tampered with in any way. 8. Use only U.L. approved wire connectors for all electrical connections. CAUTION: Wire connectors must be securely fastened and must completely cover exposed wire ends to prevent shock hazard. 9. Be sure to insulate unused leads INDIVIDUALLY to 600Vrms using U.L. approved wire connectors. 10. Verify that all installation and safety requirements have been completed and reinstall driver cover. After driver installation:
11. Restore power at circuit breaker, apply power to the fixture and ensure fixture is operational.