210*290mm Lighting Solutions ZigBee STOP BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK Turn power off before inspection, installation or removal. Properly ground electrical enclosure. RISK OF ELECTRIC SHOCK Follow all NEC and local codes. Use only UL approved wire for input/output connections. Minimum size 14 AWG for continuous runs. RISQUES DE DCHARGES LECTRIQUES Coupez l'alimentation avant d'inspecter, installer ou dplacer le luminaire. Assurez-vous de correctement mettre la terre le boitier d'alimentation lectrique. RISQUES D'INCENDIE Respectez tous les codes NEC et codes locaux. N'utilisez que des fils approuvs par UL pour les entres / sorties de connexion. Taille minimum 14 AWG. Save These Instructions Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. WGZ100 24-14 for P2 terminal Left : (N)Input(L)Input(L)Relay Output Right : 0-10V GND0-10V OUTDali+Dali-
32mA Translate Wireless ZigBee messaging to control electronic ballast or LED Driver:
or LED Driver or code-compliant wiring box) via code-compliant conduit) 1 driver 0-10V driver using metal mounting screws not provided). to LED Array) Type 1.B action Pollution degree 2 Rated Impulse voltage 4000V
(N) Input White
(L) Input Black
(L) Relay Output Red
(-) 0-10V GND Grey
(+) 0-10V OUT Purple Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. This device complies with Industry Canadas license exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil ettoutes les personnes. FCC sDoC statement FCC Suppliers Declaration of Conformity Brand name: GE Lighting / model number: WGZ100 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Suppliers Name: GE Lighting Solutions Suppliers Address (USA): Nela Park, Cleveland, Ohio, 44112 Suppliers phone number and / or internet contact information: 1-888-MYGELED 0-10V LED DriverZigBee to 0-10V InterfaceDriver Line (L)Driver Neutral (N)Wire Nut(N)(L)Driver 0-10V Dimming WiresDriver LED Output Wires ((+)(-)Fixture Mains (Fixture Driver Housing ((+)(-)The interface and wiring is intended to be installed and completely enclosed within the same NEC Class housing as the ((Relay Output)(L)(N)(Relay Output)(N)(L)