2.4GHz WIRELESS MODULE OBM1000CTSD01 OBM1000CTSD01 is a wireless control module which operates at 2.4GHz ISM band and support RX/TX half duplex mode. Typical application of the module is dimming and color temperature LED driver or other smart appliance control. FCC ID: PUU-LINKABLE-OB01 IC:10798A-LINKABLE001 Module Features SOC integrated MCU and RF transceiver 9 GPIOsincluding 10bit/16bit PWM 10bit ADC GPIO Working voltage 2.2-3.6V Maximum Transmit power +7dbm Receive sensitivity -93dbm@250Kbps Sleep mode current 8uA @3.3V Receive mode current 20mA @3.3V Transmit mode current 34mA@8dbm, 3.3V Support custom function development DC Electrical Characteristics Unit Test condition Min 2.0 Typ. 3.3 Parameter Working Voltage Output Low-voltage Output High-voltage using strong pull-up Port output PW M frequency Output PWM Duty Sleep mode current Working current 90%Vcc 0 Working temperature
-20 Max 3.6 0.45 V V V 5 43.2 kHz 100 8 34 85
%
uA mA 20 IOH=-8mA IOH=-15mA 16 MHz IRC, Output accuracy 1% in 1%~100%
dimming LVR function off, 3.3V 3.3V On-Bright Electronics Confidential User Manual OB_DOC_UM_M1000CTSD0100EN 1 2.4GHz WIRELESS MODULE OBM1000CTSD01 Appearance Parameter Typ. A B C D 34.00 14.00 2.30 2.00 Unit MM MM MM MM Shielding case size 21.3MM x 9.5MM x 3.0MM On-Bright Electronics Confidential User Manual OB_DOC_UM_M1000CTSD0100EN 2 2.4GHz WIRELESS MODULE OBM1000CTSD01 Port Definition Number Symbol Description 1 2 3 4 5 6 7 8 9 10 11 GND Ground VCC Working voltage 2.0V~3.6V IO IO IO IO IO IO IO IO IO ADC GPIO PW M ADC ADC/GPIO GPIO ADC GPIO GPIO On-Bright Electronics Confidential User Manual OB_DOC_UM_M1000CTSD0100EN 3 2.4GHz WIRELESS MODULE OBM1000CTSD01 FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Safety Caution statement To satisfy FCC RF exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirement.
On-Bright Electronics Confidential User Manual OB_DOC_UM_M1000CTSD0100EN 4 2.4GHz WIRELESS MODULE OBM1000CTSD01
IMPORTANT NOTICE
RIGHT TO MAKE CHANGES
On-Bright Electronics Corp. reserves the right to make corrections, modifications, enhancements,
improvements and other changes to its products and services at any time and to discontinue any
product or service without notice. Customers should obtain the latest relevant information before
placing orders and should verify that such information is current and complete.
WARRANTY INFORMATION
On-Bright Electronics Corp. warrants performance of its hardware products to the specifications
applicable at the time of sale in accordance with its standard warranty. Testing and other quality
control techniques are used to the extent it deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
On-Bright Electronics Corp. assumes no liability for application assistance or customer product
design. Customers are responsible for their products and applications using On-Brights components,
data sheet and application notes. To minimize the risks associated with customer products and
applications, customers should provide adequate design and operating safeguards.
LIFE SUPPORT
On-Bright Electronics Corp.s products are not designed to be used as components in devices
intended to support or sustain human life. On-bright Electronics Corp. will not be held liable for any
damages or claims resulting from the use of its products in medical applications.
MILITARY
On-Bright Electronics Corp.s products are not designed for use in military applications. On-Bright Electronics Corp. will not be held liable for any damages or claims resulting from the use of its products in military applications. On-Bright Electronics Confidential User Manual OB_DOC_UM_M1000CTSD0100EN 5