1 2 3 4 5 6 12 Back 7 8 9 10 11 All the figures of the manual are for referance only, please make the object as the standard. 1.Smartphone mount 2.Rollaxis 3.Tilt axis 5.ON/OFF 7.Power indicator 9.Joystick 4.Panaxis 6.Shifter Lever 8.USB port 10.18650 Li-ion battery 11.1/4 inch screw thread 12.Charging indicator Camera protection sticker for pan axis motor Smooth gimbal Counterweight Micro USB cable 18650 Li-ion battery User Manual Unscrew the battery cover, load the 18650 battery and then screw and tighten the battery cover. Note: Ensure that the battery cover is fully tightened or else the gimbal may not power on. 2 1 Open the smartphone mount, insert your smartphone and the mount will hold it tightly in place. Press and hold on the ON/OFF Power button for more than 3 second and the gimbal starts to work. Press and hold on the joystick for more than 3 seconds and the gimbal enters standby mode, press the joystick for 1 second to turn on the gimbal. USB Firmware Update.... Please load the 18650 Li-ion battery before upgrading. Connect the gimbal to a computer with the Micro USB cable to do upgrade or calibration. The USB cable can be used for direct charge without removing the battery. 18650 Li-ion battery Capacity: 3400mAh Voltage: 3.7V The gimbal must be matched with the original batteries; if not, the performance and safety will not be guaranteed. Zhiyun assumes no liability for damages or injuries under this circumstance. 5 2 1 0 9 When the smartphones vertical gravity center tilts forward and backward, please loosen the thumbscrew at the back of smartphone mount, adjust the smartphone mount to vertical status until it wont shake even the gimbal swings at any directions (The smartphone mount can be directly adjust to the bottom when using an iPhone 6 Plus). 90 When the horizontal gravity center tilts downward due to smartphones overweight, please mount the counterweight onto the tilt axis so that the smartphone keeps level, as thus the gimbal can work normally (the counterweight must be mounted with the size of iPhone 6 Plus and above or the gimbal cannot work normally). Adjusting the gravity center makes the gimbal works more efficiently. When the gravity center is not in balance, the gimbal still works, but the motors consume excessive power and, meanwhile, the motors torque for stabilizing will be lessened. s ON/OFF 1.Power (Press and hold on for more than 3 seconds). 2.The Confirm button of the APP menu. ON/OFF Shifter Lever 1.Help focus when taking a photo by APP. 2. The UP/DOWN button of the APP menu. Shifter Lever Power Indicator Light 1.The yellow light is the indicator of switching on/off the gimbal (Switch on: the light quickly flashes for 3s and keeps on for 1s, then goes out; Switch off: the light quickly flashes for 3s then goes out). 2.The blue light is the indicator of power(Flashes 4 times: 75%-100%;Flashes 3 times: 50%-75%;
Flashes 2 times: 25%-50%;Flashes rapidly:
0%-25%). Joystick 1. The joystick helps adjust four directions of the camera. 2. Press the joystick to switch modes. The default mode is Mode, single press the joystick to switch to Locking Mode, single press the joystick again to go back to Pan and tilt Following Mode. Pan Following Joystick Joystick J J o o y y s s ti ti c c J o y k k s ti c k Joystick Joystick Joystick Joystick Joystick Joystick Joystick back to previous tilt move the Joystick UP/DOWN tilt Joystick UP/DOWN LEFT/RIGHT to adjust roll angle. tilt tilt the Joystick LEFT/RIGHT tilt move the Move the Joystick tilt move Initialization may be required if the following behavior is observed:
1. After the gimbal starts, the tilt angle of the camera deviates slightly from a level position. 2. After the gimbal starts, the roll angle of the camera deviates slightly from a level position. 3. When remaining still, the pan axis makes frequent small angle corrections. Initialization process:
1. Install the camera and batteries correctly. 2. Press and hold on the power button for more than 3 second and the gimbal starts to work. 3. Press the joystick and the gimbal enters standby mode. 4. Place the gimbal on a level surface in any position where the gimbal will stay stationary, keep it still for more than 30 seconds and the initialization will complete automatically. 9 changes). Calibration Method For online calibration, please log in Zhiyun official website:
www.zhiyun-tech.com USB Driver, and follow the tutorial video at the right bottom of home page. Or connect the Zhiyun APP(Zhiyun Assistant) to do calibration. to download Zhiyun Gimbal Tools and the 10 1 Connect the gimbal with smartphone Turn on the gimbal power. Open the Bluetooth in phone settings. PONY Place the smartphone nearby the gimbal, and then the waiting page shows the gimbal name. click the name to connect. 2 Download APP First, please download APP from our official website:
www.zhiyun-tech.com .Android users also can scan the left QR Codes to download. For iOS users, please search and download APP (ZhiYun Assistant ) from APP Store. Attention: Please refer to the latest APP version. More fun waiting for you to experience. 3 Main Functions Introduction PONY PONY Monitor interface To check whether there is deviation in three axes in case for calibration. Control interface Directly switch operating mode and all functions corresponding to the joystick. PONY PONY Calibration interface When the gimbal three axes deviate slightly from a level position, the gimbal needs calibration. Click START CALIBRATION, and the place gimbal as shown in the APP until the calibration is complete. Update interface Check whether the firmware is the latest one. If not, please upgrade the firmware. To ensure proper use of the batteries please read the following information carefully prior use.
,