MODULE SPECIFICATION Version: 1.0 Model No.:
191D9618 HW Version: 1.1 CONTENT I CONTENT........................................................................................................................................II 1.Summary.......................................................................................................................................1 2.Functional Block Diagram.......................................................................................................... 1 3.Module Hardware Characteristic...............................................................................................2 3.1 RF Specifications..................................................................................................................2 3.2 Electrical Characteristics.....................................................................................................4 4. Connector pin definitions...........................................................................................................5 5. Module Size.................................................................................................................................6 5.1 Sample Picture......................................................................................................................6 5.2 Mechanical Dimensions.......................................................................................................6 II 1.Summary The Module which use the Cypress CYW20707UA2 that 4.2-compliant, stand-alone baseband processor with an integrated 2.4 GHz transceiver. is a single-chip Bluetooth Features Bluetooth Device ID profile version 1.3 compliant 1Complies with Bluetooth Core Specification version 4.2 including 2 3 4 5 Supports Generic Access Profile (GAP) Supports Adaptive Frequency Hopping (AFH) Excellent receiver sensitivity BR/EDR
,without BLE mode. 2.Functional Block Diagram 1 3.Module Hardware Characteristic 3.1 RF Specifications 1.Receiver RF Specifications 2 2.Transmitter RF Specifications 4.AntennaPCB Antenna. 5.Antenna Gain: 1.43dBi(Peak), 3.2 Electrical Characteristics 1. Operation temperature range -25~+85 2. Storage temperature range-40~+125 4 4. Connector pin definitions 7Pin connectorJ101)model:TMM-107-01-F-S-SM 3Pin connector(J105) model:BM03B-XASS-TF J101 connector pin definition J101_1Pin J105_1Pin Pin 1 2 3 4 5 6 7 Signal 3V3 TXD RXD RST RTS CTS GND Description Output voltage:3.3V typ 20707 HCI UART_TX: UART transmit data 20707 HCI UART_RX:UART receive data 20707 Reset :Active-low reset input 20707 HCI UART_RTS: UART request to send output 20707 HCI UART_CTS:UART clear to send input Ground J105 connector pin definition Pin 1 2 3 Signal 5V_IN GEA2 GND Description Power supply Range:4V~6.5V(5V typ) Communication signals Ground Remark Remark 5 5. Module Size 5.1 Sample Picture 5.2 Mechanical Dimensions 6 FCC Statement Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful interference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCCRadiationExposureStatement ThismodularcomplieswithFCCRFradiationexposurelimitssetforthforanuncontrolledenvironment.Thistransmittermustnotbecolocated oroperatinginconjunctionwithanyotherantennaortransmitter. IftheFCCidentificationnumberisnotvisiblewhenthemoduleisinstalledinsideanotherdevice,thentheoutsideofthedeviceintowhichthe module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
ContainsTransmitterModuleFCCID:ZKJBLEC002OrContainsFCCID:ZKJBLEC002 Whenthemoduleisinstalledinsideanotherdevice,theusermanualofthehostmustcontainbelowwarningstatements;
1.ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference.
(2)Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Thedevicesmustbeinstalledandusedinstrictaccordancewiththemanufacturer'sinstructionsasdescribedintheuserdocumentationthat comeswiththeproduct.