DS-PD2-D15E 15m Dualech Detector 1: Disassembling the KX a) Printed Circuit Board b) Lens Illuminator 2: The Printed Circuit Board b) Mains Frequency 50Hz
(Default) 60Hz c) S ty Auto/High See Sec a) Terminals 3: Cable Entry + Moun a) Moun Screw Knockouts b) Cable Entry Knockout e) PCB Screw d) Lens Holder f) Back Tamper f) Nut g) Casing Screw d) AND/OR See sec e) ALARM LED LED Disable LED Enable
(Default) h) Microwave Poten ter g) Pyro Sensor DO NOT TOUCH f) Tamper and Alarm Resistor Headers c) Case Lid Screw F This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European 2011/65/EU. 4: Bracket Connec c) Lens 5: Installa Hints a) Ceiling Bracket F Do not par completely obscure the detectors Avoiding False Alarms LEDs. Onc ready to use. tector is 1. Avoid placing the detector in direct sunlight. 2. Do not let pets and other animals wander freely whilst the alarm system is armed. 3. Do not mount the detector near heaters or radiators. 4. Do not mount the detector near open windows or ty S 6: S a) Auto S ty (Default) b) High S ty 7: AND/OR Mode 8: Microwave Poten ter 9: EOL Resistor Headers AND microwave Dual Tech (Both technologies need to Conven be triggered simultaneously to generate an alarm) OR If either single technology detects prolonged ty an alarm will be generated intruder ac The device has 2 set of header pin s at the top of the printed circuit board. These headers are used to select the End of Line resistance for EOL wiring applica s. If EOL wiring is not used, leave the headers OFF. 8 K 6 6 K 5 7 K 4 K 1 TAMPER 6 K 5 7 K 4 2 K 2 K 1 ALARM Minimum Range (0m) Maximum Range (15m) 11: Powering Up b) Single End of Line Wiring c) Double End of Line Wiring d) Two Double End of Line Detectors to One Input ALARM CONTROL PANEL 1 E N O
+ - Z M O C R E P M A T R E P M A T The connec shows the example value 4k7 for tamper
(EOL). ALARM CONTROL PANEL 1 E N O
+ - Z M O C R E P M A T R E P M A T The connec shows the example values of 4k7 for Alarm and 4K7 for tamper
(EOL). ALARM CONTROL PANEL 1 E N O
+ - Z M O C R E P M A T R E P M A T ows The connec the example values 4k7 for alarm, 4k7 for tamper (EOL).
+ -
Link
+ -
LEDs. Onc ready to use. NOT READY
tector is READY C5 b) Wall Bracket F 10: Choose the Connec a) Normally Closed Type:
ALARM CONTROL PANEL 1 E N O
+ - Z M O C R E P M A T R E P M A T
+ -
ALM ALM TAMPER
+ -
ALM ALM TAMPER
+ -
ALM ALM TAMPER
+ -
ALM ALM TAMPER
+ -
ALM ALM TAMPER 8 K 6 6 K 5 7 K 4 K 1 TAMPER 8 K 6 6 K 5 7 K 4 K 1 TAMPER 8 K 6 6 K 5 7 K 4 K 1 TAMPER 8 K 6 6 K 5 7 K 4 K 1 TAMPER 8 K 6 6 K 5 7 K 4 K 1 TAMPER ALARM 6 K 5 7 K 4 2 K 2 K 1 Detector ALARM 6 K 5 7 K 4 2 K 2 K 1 Detector ALARM 6 K 5 7 K 4 2 K 2 K 1 Detector ALARM 6 K 5 7 K 4 2 K 2 K 1 Detector ALARM 6 K 5 7 K 4 2 K 2 K 1 Detector 12: The 15m Volumetric Lens 13: Dimensions and Weight 15:
85 60 zones 7 planes RLNS074
* In an EN50131-1 (and INCERT) system the maximum detec 117 x 69 x 50mm 125g (4.4 oz) without bracket 85, 60zones, 7planes 15m 1.8-2.4m yes Coverage Maximum range Op mal installa on height Creep-zone protec on Key features Blue Wave Technology yes yes Automa c sensi vity Digital temperature compensa on yes Separate indica on: microwave, PIR and alarm yes 3 microwave frequencies to avoid interference yes yes DEOL resistors on board yes Tamper protec on included Signal Strength Indicators (SSI) n/a Wired Power supply Current consump on at rest Current consump on in alarm Relay type Output relay Tamper terminal 9-16 DC (12DC nominal) 23mA 30mA Solid state 60DC, 50mA protec on 12DC max, 50mA max Electrical specica ons Microwave frequency Alarm response Detec on speed Direct light lter Op cs Geometric lens congura on Other details Opera ng temperature Weight Dimensions Accessories Wall/ceiling brackets included Cer ca ons and warranty Electrical conformity Warranty 10.515, 10.525, 10.535GHz 2.5 second 0.3 - 3m/s 6500 Lux Sealed 3D
-10C / +40C 125g 117 x 69 x 5mm yes CE 2 years
!
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
!
This product operates in a European non-harmonised frequency band User Manual COPYRIGHT 2018 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED.
Manual) cannot be reproduced, changed, translated, or
About this Manual This manual is applicable to detector.
latest version in the company website
Please use this user manual under the guidance of professionals. Trademarks Acknowledgement and other Hikvisions trademarks and logos are the
owners.
the party responsible for compliance could void the users authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
frequency energy and, if not installed and used in accordance with the
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
the receiver is connected. Consult the dealer or an experienced radio/TV technician for help
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that