Specification & Operation Manual
(Remote Control Unit, Lever Control Unit, Pedal Control Unit, Main Controller) This document is property of Hanwha and disclosure, reproduction or duplication in whole or in part is prohibited without its authorization. Use for the data contained in this document is permitted only for manufacturing on Hanwha's behalf. In case of controversial interpretation of the provisions herein contained, Hanwha shall guard legally its right. 1. Specification 1.1. Remote Control Unit Device for controlling the lever & pedal remotely using wireless communication No. Description Range Dimension Weight Power Power Supplier 298 x 144 x 212 mm 2.3 kg 7.4 V
- Ni-MH(Nickel-Metal hydride) Battery
- Battery 2ea (1 for operation / 1 for Spare) Standard operating time 8 hours (continuous operation at 20) 1 2 3 4 5 6 7 8 9 Battery recharging time Operating Temperature Storage Temperature Operating Humidity 10 Dustproof and Waterproof 1.2. Lever Control Unit 2 hours
-20 ~ +55
-40 ~ +77 0 ~ 95%
IP65 Grade Device for controlling the excavator lever at operator's command using remote control unit No. 1 2 3 4 5 6 7 8 Description Dimension Weight Power Range 125 x 200 x 85 mm 1.5 kg 24 V Power Supplier Cigar jack (with Battery) Operating Temperature Storage Temperature Operating Humidity Dustproof and Waterproof
-20 ~ +55
-40 ~ +77 0 ~ 95%
IP54 Grade 1.3. Pedal Control Unit Device for controlling the excavator pedal at operator's command using remote control unit No. 1 2 3 4 5 6 7 8 Description Dimension Weight Power Range 135 x 140 x 110 mm 2.5 kg 24 V Power Supplier Cigar jack (with Battery) Operating Temperature Storage Temperature Operating Humidity Dustproof and Waterproof
-20 ~ +55
-40 ~ +77 0 ~ 95%
IP54 Grade 1.4. Main Controller Device for controlling the Lever & Pedal Control Unit at operator's command using Remote Control Unit No. 1 2 3 4 5 6 7 Description Dimension Power Range 125 x 250 x 100 mm 24V Power Supplier Cigar jack (with Battery) Operating Temperature Storage Temperature Operating Humidity Dustproof and Waterproof
-20 ~ +55
-40 ~ +77 0 ~ 95%
IP54 Grade 2. Preparation 2.1. Parts 2.1.1. Lever Control Unit No. Name Unit No. Name Unit Grip Fix Tilt Grip Fix 1 Grip Fix 2 Grip Fix 3 Lever Wire Left Lever Wire Right 2EA 2EA 2EA 2EA 1EA 1EA Shaft Joint 23EA M4 x 8mm Bolt(Wrench) 10EA M3 x 12mm Bolt(Wrench) 8EA 10 M3 x 8mm Bolt(Wrench) 4EA 11 M2.5 x 6mm Bolt(Wrench) 4EA 12 13 14 15 16 17 18 Motor Bush Spacer Shaft Fixer Clipper Shaft Lever Adapter Rubber Lever Adapter 4EA 4EA 2EA 8EA 2EA 2EA 2EA 1 2 3 4 5 6 7 8 9 2.1.2. Pedal Control Unit No. Name Unit 1 2 3 4 5 6 7 Pedal Connector(R) Pedal Connector(L) Roller External Support M10 Bolt M10 Nut M6 x Bolt(Wrench) 1EA 1EA 2EA 2EA 4EA 4EA 8EA 2.2. Tools
[ Box tool set ]
[ Wrench set ]
No. 1 2 Name Box tool set Wrench set Unit 1SET 1SET 3. Installation 3.1. Level Control Unit 3.1.1. Lever Adapter Installation Order Figure Note Parts and Tool
- Put the adapter on the adapter rubber of the lever.
- Do not pull powerfully to split the rubber of the lever rubber.
- Lever Adapter
- When the Clippers are inserted, Please check
- Clipper that the clippers include adapter, adapter rubber
- Wrench(M2.5) and control stand. 1 2 3.1.2. Lever Neck Gripper Installation Order Figure Note Parts and Tool 1 2 3 4 5
- After take off the lever flexible rubber, Insert the
- Grip Fix 3 Grip Fix 3 under the lever.
- Bolting after Insert the Grip Fix 2 where the opposite side of the Grip Fix 3.
- Grip Fix 2
- Bolts(M3 x 4)
- Please be sure that Grip fix2 and Grip fix3 contacted.
- Wrench(M3)
- Put in the Grip Fix 1 in front of the Grip Fix 2 and
- Bolts(M3 x 2)
- Grip Fix 1 Bolting
- Wrench(M3)
- Put the Grip Fix Tilt into the hole of the Grip Fix 1.
- Do not confuse the side of the Grip Fix Tilt.
- Bolts(M2.5 x 2)
- Grip Fix Tilt
- Do not tighten up the
- Wrench(M2.5) screws cause you will tuning this part.
- Connect the Shaft joint to
- Shaft Joint Grip Fix Tilt.
- Screw(M4 x 1)
- Do not tighten up the screw also this will be tuned.
- Wrench(M4) 3.1.3. Installation to Adapter Order Figure Note Parts and Tool 1 2
- Motor Bush
- Spacer
- To the rotating part of the Motor, put the Motor
- Shaft Bush, Spacer, Shaft and Shaft Fixer sequentially.
- Fix the Shaft and Shaft Fixer using the headless screws.
- Shaft Fixer
- Screws(M4 Headless,M3 Headless)
- Wrench(M2, M1.5)
- Attach the Lever control Unit on the Adapter.
- Please sure that Shaft should be connected and pass through the Shaft Joint.
- Please mate the Align pin and the align hole of the Adapter When you connect the Lever Unit and Adapter.
- Tighten the screws on the 4points of the Lever control Unit.
- Shaft Joint
- Lever Control Unit with Shaft
- Screws(M4 x 2)
- Wrench(M4) 3.1.4. Horizontal Matching Order Figure Note Parts and Tool 1 2
- After Installation of the Lever Control Unit, You have the one more step to operate machine well.
- You need to tuning the some parts.
- First of all, tune the Grip Fix Tilt until the Shaft Joint positioning the half position of the Shaft when Lever is in neutral position.
- Wrench(M2.5, M4)
- Second, Make Parallel between Lever shaft and Robot Shaft for the performance of the Lever Control Robot. 3.2. Pedal Control Unit 3.2.1. Pedal Adapter Installation Order Figure Note Parts and Tool 1
- Take the Foot Rest off the excavator.
- Install the Pedal Adapter.
- Wrench(M8) 3.2.2. Pedal External Support Installation Order Figure Note Parts and Tool 1
- Assemble the Roller and Pedal external support.
- Roller
- Take off the Pedal Handle of the Pedal .
- External Support
- Install the assembled part the opposite position
- Box of the pedal handle like second photo. Order Figure Note Parts and Tool
- Match the Slide Link and Roller attached on the pedal.
- Wrench(M6)
- After match, lay the
- Screws(M6 x 4) pedal control unit on the adapter and bolting. 2 3.3. Wiring Order Figure Note Parts and Tool 1 2 3
- Put the Lever cable to the lever control unit.
- On the other side, of the Cable(4Pin x 2)
- Lever Cable, connect to the main controller.
- Same as the Lever unit,
- Pedal
- Pedal unit is connected Cable(4Pin x 2) with Main Controller.
- The communication box is connected with main
- Communication controller through 6pin Cable(6pin) cable.
- In case of Key box, connected with communication box Through 2pin cable.
- Key box cable(2pin)
<Lever Cable Connecting>
<Pedal Cable Connecting>
<Key Box and Communication Box Cable Connecting>
Order Figure Note Parts and Tool
<Power Cable Connecting>
- Power cable is two type as you see the picture, first
- Cigar Jack is Cigar jack and second is Cable 2pin power cable.
- Power Cable(2Pin)
- Cigar jack will be connected with Excavator.
- 2Pin power cable will be connected with main controller and battery. 4 4. Operation After Level/Pedal Control Unit is finished the installation, excavator lever and pedal can be operated by using Remote Control Unit. Joysticks of Remote Control Unit to control excavator level/pedal are configured as follows. 4.1. Lever Control Unit Motion Note Left Lever Control Unit forward Push the left lever joystick to forward(). Then left lever direction operation control unit operate the excavator left lever to forward(). Left Lever Control Unit Push the left lever joystick to backward(). Then left lever backward direction operation control unit operate the excavator left lever to backward(). Left Lever Control Unit left Push the left lever joystick to left side(). Then left lever direction operation control unit operate the excavator left lever to left side(). Left Lever Control Unit right Push the left lever joystick to right side(). Then left lever direction operation control unit operate the excavator left lever to right side(). Right Lever Control Unit Push the right lever joystick to forward(). Then right lever forward direction operation control unit operate the excavator right lever to forward(). Right Lever Control Unit backward direction operation Push the right lever joystick to backward(). Then right lever control unit operate the excavator right lever to backward(). Right Lever Control Unit left Push the right lever joystick to left side(). Then right lever direction operation control unit operate the excavator right lever to left side(). Right Lever Control Unit right Push the right lever joystick to right side(). Then right lever direction operation control unit operate the excavator right lever to right side(). 4.2. Pedal Control Unit Motion Note Left Pedal Control Unit forward Push the left pedal joystick to forward(). Then left pedal direction operation control unit operate the excavator left pedal to forward(). Left Pedal Control Unit backward direction operation Push the left pedal joystick to backward(). Then left pedal control unit operate the excavator left pedal to backward(). Right Pedal Control Unit forward direction operation Push the right pedal joystick to forward(). Then right pedal control unit operate the excavator right pedal to forward(). Right Pedal Control Unit backward direction operation Push the right pedal joystick to backward(). Then right pedal control unit operate the excavator right pedal to backward(). FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions :
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. CAUTION : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.