HEBEI HUACHUANGDA TECHNOLOGY CO.LTD
HCD-1215L1CON CONTROLLER INSTRUCTION
7
The electronic board is used for kid car, and controls kid car to move forward,move back, swing. Also,can adjust speed accordingly.
Power by battery to drive motor, turn via motor too.
1 use right adapter to recharge the battery, keep the value belong to 6-12 voltage output.And keep away from children when
2 Pay attention to the color wire to connect, take care of positive pole and negative pole. Bus line,jumpers connected correctly.
3 Do not dip into water, in case of shortcut.
4 Do not expose the board under rainy, under sun.
5 Press the button power firstly,the car is stand by. Press rock button, the kid car swing from time to time, until the run button is
recharging.
pressed.
6 Under the run status,step on the pedal to accelerate,loose to decrease speed. At the same time, pust the rocking bar to forward
or back.
From the acousto-optic wire, the board can receive blue tooth signal in 2.4G frequency, and operate the kid car to move. That
means, the remote control box can treat, and cell phone can treat via APP.
Specification:
Supported type:
Bluetooth low Energy
Modulation:
GFSK
Operation frequency:
2402MHz to 2480MHz
Channel number:
Channel separation:
40
2 MHz
Max Peak Power:
-3.0dbm
is
of
of
to
to
to
to
by
15
(1)
has
and
and
and
and
user’
found
subject
thi
incl
on, the user
not installed
the equipment off
interference that may
the FCC rules. Operation
the FCC Rules. These limits are designed
guarantee that interference will not occur
the party responsible for compliance could void the
operate the equipment.
been tested
and
cause undesired operation.
the following two conditions:
(2) this device must accept any interference received,
a residential installation. This equipment generates uses
accordance with the instructions, may cause harmful interference
in
no
is
comply with the limits for a Class B digital device, pursua
provide reasonable protection against harmful inte
can radiate radio frequency energy a
radio com
this
If
turn
by
the
of
FCC Statement
This device complies with part
s device may not cause harmful interference,
uding
modifications not expressly approved
or
Changes
s authority
to
NOTE: This equipment
15
nt
part
to
in
rference
nd,
used
if
munications. However, there
equipment does cause harmful interference
ing
following measures:
‐
‐
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your
body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna,
Reorient
Increase the separation between the equipment and receiver.
a particular installation.
determined
more
or
one
television reception, which can
correct the interference
try
experienced radio/TV technician for help important announcement
relocate the receiving antenna.
radio
encouraged
or
to
be
by
an
or
or
to
to
in
is
be
the
met
these
event
cannot
example
conditions
As long as the two conditions above are met, further transmitter testing will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
Important Note:
In
co-location
(for
that
with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
final end product must
The
2A2MNHCD-1215L1CON"
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
a visible area with the following" Contains FCC ID:
configurations
labeled
certain
laptop
be
or
in
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM
Manual v01
2.2 List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational use conditions
This module
different
involve
operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer
for the installation method in end system.
2.4 Limited module procedures
This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module
limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host designs
prior to giving the host manufacturer approval.
2.5 Trace antenna designs
Not applicable
is stand-alone modular.
Multiple simultaneously
transmitting condition
product
If the
end
the
will
or
2.6 RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
2.7 Antennas
This radio transmitter FCC ID:2A2MNHCD-1215L1CON
operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list
gaingreater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
that have a
Communications Commission to
has been approved by Federal
Model
Type
Connector
BLE
PCB
/
5150-5250
MHz
/
Peak gain ( dBi )
5250-5350
MHz
/
5470-5725
MHz
/
5800
MHz
/
2400-
2500MHz
dBi
0
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following" Contains FCC ID:2A2MNHCD-1215L1CON".
2.9 Information on test modes and additional testing requirements
Host manufacturer which install this modular with limit modular approval should perform the test of radiated emission and spurious
emission according to FCC part 15C:15.247
15.209
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for
the system such as Part 15 B.
requirement, only if the test result comply with FCC part 15.247 and
requirement, then the host can be sold legally.
and 15.209