FCC ID: Q9DAPINH303 802.11a/b/g/n/ac Wireless Access Point

Aruba 303H Series Hospitality Access Point Installation Guide The Aruba AP-303H access points are high-performance dual-radio wireless devices for hospitality and branch deployments. These access points use Multiple-Input, Multiple-Output (MIMO) technology to provide secure wireless connectivity for both 2.4GHz 802.11 b/g/n and 5GHz 802.11 a/n/ac WiFi. Alternatively, the wired Ethernet ports located on the bottom of this access point allow users to connect directly to the device when physically linked by an Ethernet cable. The AP-303H can be attached to a standard single-gang wall box using the mount provided, or converted into a desk-mounted remote access point for branch office deployments using the AP-303H-MNTD mount kit (sold separately). The AP-303H access point provides the following capabilities:

Dual wireless transceivers

IEEE 802.11a/b/g/n/ac operation as a wireless access point

IEEE 802.11a/b/g/n/ac operation as a wireless air monitor

Compatibility with IEEE 802.3af/at PoE

Central management configuration

Supports PoE-in (E0 port)/PoE-out (E3 port)

Support for selected USB peripherals

Integrated Bluetooth Low Energy (BLE) radio Package Contents

AP-303H Access Point

Single gang wall-box mounting bracket

(2x) #6-32 slotted screws

T8H Torx security screw

ArubaOS Quick Start Guide Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Software The AP-303H access point requires ArubaOS 6.5.2 or higher. For additional information, refer to the ArubaOS User Guide and ArubaOS Quick Start Guide. Hardware Overview The following sections outline the hardware components of the AP-303H access point. LED The LED displays located on the front and bottom of the access point indicate the following functions:

0511xxx-01 | November 2016 1 Figure 1 Front PoE-PSE Status Radio Status System Status System Status The System Status LED indicates the operating condition of the access point, as shown in Table 1. Table 1 System Status LEDs Color/State Meaning Off Device is powered off Green/solid Device is ready; fully functional Green/blinking1 Device is booting; not ready Green/flashing2 Device is ready; uplink negotiated at suboptimal speed (<1Gbps) Amber/solid Amber/flashing Device is ready; operating in power-save mode

(PoE source: 802.3af). Device is ready; operating in power-save mode, with uplink negotiated at suboptimal speed (<1Gbps) Red/solid Error condition 1 blinking: 1s on/1s off 2 flashing: on/off repeated in less than 1s Radio Status The Radio Status LED indicates the operating mode of the access points radios, as shown in Table 2. 2 Aruba 303H Series Hospitality Access Point | Installation Guide Table 2 Radio Status LEDs Color/State Meaning Off Meets one of the following conditions:

both radios are disabled

device is powered off Green/solid Both radios enabled in access mode Green/blinking1 One radio enabled in access mode; one radio disabled Amber/solid Both radios enabled in monitor mode Amber/flashing Device ready; operating in power-save mode, with uplink negotiated at suboptimal speed (<1Gbps) Alternating3 Error condition Network Status The Network Status LED, located on the sides of the E1-E3 ports, indicates activity transmitted to/from the wired ports, as shown in Table 3. Table 3 Network Status LEDs Color/State Meaning Off Meets one of the following conditions:

device is powered off

port is disabled

no link/activity Green/solid Link established at max speed (1Gbps) Green/blinking Activity detected across a max speed link Amber/solid Link established at reduced speed (10/100Mbps) Amber/blinking Activity detected across a reduced speed link PoE-PSE Status The PoE-PSE LED are located above ports E1-E3, and indicate when the access point is operating as Power Sourcing Equipment (PSE), providing Power over Ethernet (PoE) to an external device that is physically connected to the E3 port by Ethernet cable, as shown in Table 4. Table 4 PoE-PSE Status LEDs Color/State Meaning Off Access point not supplying PoE, or powered off Green/solid Access point supplying power to a connected device Green/blinking Negotiating PoE power supplied to a connected device Aruba 303H Series Hospitality Access Point | Installation Guide 3 LED Display Settings The LEDs have three operating modes that can be selected in the system management software:

Default mode: Refer to Tables 1-3

Off mode: LEDs are off

Blink mode: LEDs blink green Figure 2 Back Panel 0 E A m 0 0 6 V 7 5 P T

The rear panel of the AP-303H may become hot after extended use. Console Port The 5-pin USB Micro-B connector located on the back of the access point allows for direct management of the device when connected to a laptop or serial console. For pin-out details, refer to Figure 3. Figure 3 Console Port Pin-out 1 2 3 4 5 USB Micro-B 1: NC 2: RX 3: TX 4: GND 5: GND Ethernet Ports The AP-303H access point is equipped with four active Ethernet ports (E0-E3). Refer to Figure 4. 4 Aruba 303H Series Hospitality Access Point | Installation Guide Figure 4 Bottom E0 E1 E2 E3 E0 The E0 port, located at the bottom of the access point is 10/100/1000 Base-T, auto-sensing, MDI/MDX wired-

network uplink connectivity RJ45 port. It supports IEEE 802.3af/802.3at PoE as a standard Powered Device (PD) from Power Sourcing Equipment (PSE), such as a midspan injector or a network infrastructure that supports PoE. The E1-E3 ports, located at the bottom of the access point are 10/100/1000 Base-T auto-sensing, MDI/MDX wired-network downlink connectivity RJ45 ports. These ports are used to provide secure network connectivity to wired devices when physically linked using an Ethernet cable. Refer to Figure 5 for port pin-out information. Additionally, the E3 port supports PoE-out functionality, and is capable of supplying up to 13W to PSE when t access point is operating in 802.3at PoE mode, or powered by a DC source. Figure 5 Gigabit Ethernet Port Pin-Out USB Interface The AP-303H access point is equipped with a USB port that is compatible with cellular modems and Bluetooth Low Energy (BLE) dongles. When active, the USB port can supply up to 5W/1A to a connected device. Figure 6 Side 4 8 V 6 0 0 m A AC/DC power socket USB port Reset button Security Screw Lock Push Button The push button located on the right side of the device can be used to reset the access point to factory def settings or turn off/on the LED display.

To reset the access point to factory default settings:

1. Power off the access point. 2. Press and hold the push button using a small, narrow object, such as a paperclip. 3. Power-on the access point without releasing the push button. The system status LED will flash within 5 seconds. 4. Release the push button. The system status LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings.

To turn off/on the system status LED:

During the normal operation of the access point, press the push button using a small, narrow object, such as a paperclip. The system status LED will be turned off/on immediately. Aruba 303H Series Hospitality Access Point | Installation Guide 5 Power Supply The AP-303H access point has a single 48V DC power connector to support AC-to-DC power using an AP-AC-48V36C power adapter (sold separately). The power connector port is located on the side of the device, as shown in Figure 6. The AP-303H access point supports both PoE-in and PoE-out functionality. The PoE-in (PoE-PD) allows the E0 port to draw power from an 802.3at (preferred) source, or an 802.3af (optional) source. When powered by an 802.3at or DC power source, the PoE-out (PoE-PSE) functionality is enabled on port E3, supplying a maximum output of 15W to a wired device. Refer to Table 4 for power output details. PoE-PSE and USB settings can be enabled/disabled through the softwares WebUI and CLI. Table 5 Power Mode Output Power Source DC (AP-AC-48V36C) 802.3at 802.3af Restrictions PoE-PSE enabled; USB enabled PoE-PSE enabled; USB disabled PoE-PSE disabled; USB disabled When both DC and PoE power are simultaneously available, the access point will default to using DC power, while continuing to draw a minimal current from the PoE source. If DC power source is removed, the access point will begin drawing power from the PoE source, allowing for a hitless fail-over when switching between power sources. Before You Begin Refer to the sections below before beginning the installation process.

This device must be professionally installed and serviced by a trained ACMP or similar Aruba-certified technician.The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure to properly install this product may result in physical injury and/or damage to property. Tous les points daccs Aruba doivent tre installs professionnellement par un Professionnel en mobilit certifi par Aruba (ACMP). Il incombe au technicien dinstallation de veiller ce quune borne de raccordement la terre conforme avec tous les codes lectriques nationaux applicables puisse tre utilise. Pre-Installation Checklist Before installing the AP-303H access point, be sure that you have the following:

Pre-installed wall box

Cat5E UTP cable with network access installed in the wall box

One of the following power sources:

IEEE 802.3af/at-compliant Power over Ethernet (PoE) source

Aruba AP AC-DC adapter kit (sold separately) One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an A record

DHCP Server with vendor-specific options Aruba Networks, Inc., in compliance with governmental requirements, has designed the AP-303H access points so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User Guide. 6 Aruba 303H Series Hospitality Access Point | Installation Guide Identifying Specific Installation Locations When installing the AP-303H access point must be secured to an Aruba-approved wall or to a desk mount kit. This access point should be oriented vertically, with Ethernet ports facing downward to facilitate maximum antenna gain. Use the access point placement map generated by Arubas RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include:

Cement/concreteOld concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals.

Natural ItemsFish tanks, water fountains, ponds, and trees

Brick RF reflectors include:

Metal ObjectsMetal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

Do not place an access point between two air conditioning/heating ducts. Make sure that access points ar placed below ducts to avoid RF disturbances. RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms Installing the Access Point The AP-303H is designed to mount into a variety of electrical gang boxes. 1. Begin by removing the existing data wall plate (if applicable). 2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the UTP cable. 3. Use a short Ethernet cable (sold separately) to connect the E0 port to an RJ45 connector or crimp an RJ45 plug

(not supplied) on the cable and insert in the E0 port. Do the same for the PT port, if used. 4. Align the mounting holes of the AP-303H mounting bracket with mounting holes in you gang box, as shown in Figure 7and Figure 8. For worldwide single gang outlet box, the mounting bracket has two sets of mounti holes to meet the individual installation position requirement. The applicable standards for the wall boxes are:

IEC 60670-1, GB17466, BS4662 and DIN49073 for Worldwide

ANSI/NEMA OS 1 and OS 2 for US Aruba 303H Series Hospitality Access Point | Installation Guide 7 Figure 7 Bracket to Gang Box (US Single Gang Outlet Box Shown) Figure 8 Bracket to Gang Box (Worldwide Single Gang Outlet Box Shown) Insert the two included machine screws and tighten them to secure the mounting bracket. 5. 6. Connect any required cables to the rear of the AP-303H. 7. Align the mounting slots on the back of the AP-303H with the corresponding mounting posts on the wall mount as shown in Figure 9. 8. Push the access point against the posts and downward until the posts engage the slots at the top of the slots. 8 Aruba 303H Series Hospitality Access Point | Installation Guide Figure 9 Attaching AP-303H to Bracket 9. Once the access point is fastened onto the wall mount, insert the T8H Torx security screw into the hole located on the upper-right edge of the wall mount and tighten. 10. If not using PoE, connect the AC-DC power adapter (sold separately) to the DC power socket located on the bottom of the AP-303H. Verifying Post-Installation Connectivity The integrated LED on the Access point can be used to verify that the access point access point is receiving pow and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/

safety_addendum. All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Tous les points d'accs Aruba doivent imprativement tre installs par un professionnel agr. Ce dernier doit s'assurer que l'appareil est mis la terre et que le circuit de mise la terre est conforme aux codes lectriques nationaux en vigueur.

Electrical

Ethernet:

100/1000 Base-T auto-sensing Ethernet RJ45 interface

IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T)

Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum).

Power:

48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36) Aruba 303H Series Hospitality Access Point | Installation Guide 9

Maximum power consumption with a full PoE-PSE and USB load: 25W (PoE) or 31W (DC) If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an output rated 48VDC, minimum 2A, marked LPS and Class 2, and suitable for plugging into a standard power receptacle in the US and Canada. Environmental

Operating:

Temperature: 0C to +40C (+32F to +104F)

Humidity: 5% to 93% non-condensing

Storage and transport:

Temperature: -40C to +70C (40F to +158F) Regulatory Information The regulatory model name for AP-303H/IAP-303H access point is Regulatory model name. Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 10.63 inches (27cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Dclaration sur les limites d'exposition aux radiofrquences : cet quipement est conforme aux limites d'exposition aux rayonnements radiolectriques spcifies par la FCC. Il doit tre install et utilis une distance minimale de 27 cm par rapport votre corps pour les frquences de 2,4 et 5 GHz. Cet metteur-rcepteur ne doit pas tre utilis ou situ proximit d'autres antennes ou metteurs-rcepteurs. En cas d'utilisation dans la plage de frquences de 5,15 5,25 GHz, cet appareil doit uniquement tre utilis en intrieur afin de rduire les risques d'interfrence avec les systmes satellites mobiles partageant le mme canal.

Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval. Taiwan

Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device. 10 Aruba 303H Series Hospitality Access Point | Installation Guide

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Toute modification effectue sur cet quipement sans l'autorisation expresse de la partie responsable de la conformit est susceptible d'annuler son droit d'utilisation. Proper Disposal of Aruba Equipment Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Copyright 2016 Hewlett Packard Enterprise Development LP 11 Aruba 303H Series Hospitality Access Point | Installation Guide a Hewlett Packard Enterprise company www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax: 408.227.4550

Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products Abstract This document contains safety precautions, environmental notices, and regulatory compliance notices for Hewlett Packard Enterprise products. Part Number: 703827-402 Published: October 2016 Edition: 12 Copyright 2012, 2016 Hewlett Packard Enterprise Development LP The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein. Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise website. Contents 1 Safety precautions...............................................................................................5 General precautions.............................................................................................................................5 Symbols on equipment.........................................................................................................................5 Precautions for maintaining and servicing products.............................................................................6 Precautions for power products............................................................................................................7 Power cords.....................................................................................................................................7 Power supplies................................................................................................................................8 Uninterruptible power supply (UPS) products.................................................................................8 Power distribution units (PDUs).......................................................................................................9 Grounding......................................................................................................................................10 Voltage selection...........................................................................................................................11 Batteries........................................................................................................................................11 Fuse replacement..........................................................................................................................12 Precautions for products installed in racks and cabinets....................................................................13 Precautions for modems, telecommunications, or LAN options.........................................................13 2 Environmental notices.......................................................................................15 Waste Electrical and Electronic Equipment (WEEE) Directive...........................................................15 Battery replacement notices...............................................................................................................15 RoHS material content declarations...................................................................................................16 China RoHS material content declaration.....................................................................................16 China RoHS Hazardous Substances table...................................................................................16 India RoHS material content declaration.......................................................................................16 Taiwan RoHS Hazardous Substances table..................................................................................17 Turkey RoHS material content declaration....................................................................................17 Ukraine RoHS material content declaration..................................................................................17 Perchlorate material Special handling may apply..........................................................................18 European Union Commission Regulation 1275/2008.........................................................................19 3 Regulatory compliance notices.........................................................................20 Regulatory compliance identification numbers...................................................................................20 Federal Communications Commission notice....................................................................................20 FCC rating label.............................................................................................................................20 Class A equipment...................................................................................................................20 Class B equipment...................................................................................................................21 Modification...................................................................................................................................21 Cables...........................................................................................................................................21 Global notice for Class A equipment..................................................................................................21 Notices for Canada (Avis Canadien)..................................................................................................21 Class A equipment........................................................................................................................21 Class B equipment........................................................................................................................21 Notices for China................................................................................................................................22 Class A equipment........................................................................................................................22 Trusted Platform Module (TPM) China Import Restrictions........................................................22 Notices for European Union................................................................................................................22 European Union Regulatory Notice...............................................................................................22 Products with wireless functionality (EMF)....................................................................................22 Restrictions for product with wireless functionality........................................................................22 Notices for Japan................................................................................................................................23 VCCI notice...................................................................................................................................23 Power cord statement....................................................................................................................23 Notices for Korea................................................................................................................................23 Class A equipment........................................................................................................................23 Contents 3 Class B equipment........................................................................................................................23 Notices for Taiwan..............................................................................................................................24 BSMI notices.................................................................................................................................24 Class A EMI warning message................................................................................................24 Battery replacement notice......................................................................................................24 UPS (less than 16A output current).........................................................................................24 UPS (greater than 16A output current)....................................................................................24 Belarus Kazakhstan Russia marking..................................................................................................25 Wireless devices.................................................................................................................................27 Brazilian notice..............................................................................................................................27 Canadian notice.............................................................................................................................27 Japanese notice............................................................................................................................27 Mexican notice...............................................................................................................................27 Taiwanese notice...........................................................................................................................28 Laser compliance notices...................................................................................................................29 Index.....................................................................................................................30 4 Contents 1 Safety precautions Retain and follow all product safety and operating instructions. Always refer to the documentation

(printed or electronic) supplied with your product. If there is a conflict between this document and the product documentation, the product documentation takes precedence. Observe all warnings on the product and in the operating instructions to reduce the risk of bodily injury, electric shock, fire, and damage to the equipment. General precautions For Class A products only: The installation and maintenance of products must CAUTION:

be carried out by qualified personnel. If the product sustains damage requiring service, disconnect the product from all power sources and refer servicing to a Hewlett Packard Enterprise authorized service provider. Examples of damage requiring service include:

To reduce the risk of personal injury or damage to the product:

The power cord, extension cord, or plug has been damaged. Liquid has been spilled on the product or an object has fallen into the product. The product has been exposed to rain or water. The product has been dropped or damaged. The product does not operate normally when you follow the operating instructions. Place the product away from radiators, heat registers, stoves, amplifiers, or other products that produce heat. Never use the product in a wet location. Avoid inserting foreign objects through openings in the product. Move products with casters carefully. Avoid quick stops and uneven surfaces. Turn down the volume before using headphones or other audio devices. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions:

This symbol in conjunction with any of the following symbols indicates the presence of a potential hazard. The potential for injury exists if warnings are not observed. Consult your documentation for specific details. This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel. This symbol indicates the presence of electric shock hazards. The area contains no user or field-serviceable parts. Do not open for any reason. WARNING: To reduce risk of injury from electric shock hazards, do not open this enclosure. General precautions 5 This symbol on an RJ-45 receptacle indicates a Network Interface Connection. WARNING: To reduce risk of electric shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle. This symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. This symbol indicates the presence of a moving fan blade. If the spinning blades are contacted, the potential for injury exists. WARNING: Hazardous moving parts. Keep away from moving fan blades. To reduce the risk of injury from a hot component, allow the surface to cool before touching. These symbols on power supplies or systems indicate that the equipment is supplied by multiple sources of power. WARNING: To reduce the risk of injury from electric shock, remove all power cords to completely disconnect power from the system. OR This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manual material handling. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. To prevent damage, observe antistatic precautions. This symbol indicates the presence of a laser device in the product that may exceed Class 1 limits. Refer to the product documentation for more information. Precautions for maintaining and servicing products To reduce the risk of electric shock or damage to the equipment when installing, maintaining, or servicing products, observe the following precautions:

Some products contain power supplies that are capable of producing hazardous energy levels. Refer to the documentation included with your product to determine whether it contains these power supplies. The installation of internal options and routine maintenance and service of this product should be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with equipment containing hazardous energy levels. Allow the product to cool before removing covers and touching internal components. 6 Safety precautions Do not use conductive tools that could bridge live parts. Remove all watches, rings, or loose jewelry when working in hot-plug areas of an energized server, storage, networking, or rack product. Do not attempt to defeat safety interlocks (where provided). Some products have covers or doors to access hot-plug components and may allow access to hazardous energy circuits or moving fans. The doors should remain locked during normal operation. OR The server, storage, networking, or rack product should be installed in a controlled access location where only qualified personnel have access. Power down the equipment and disconnect all power cords before removing any access covers for non-hot-plug areas. Do not replace non-hot-plug components while power is applied to the product. First, shut down the product and disconnect all power cords. Do not exceed the level of repair specified in the procedures in the product documentation. All troubleshooting and repair procedures are detailed to allow only subassembly or module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. For floor-standing products, install and extend bottom stabilizers before installing options and boards. Verify that the AC power supply branch circuit that provides power to the rack is not overloaded. This will reduce the risk of personal injury, fire, or damage to the equipment. The total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements. Precautions for power products Power cords To reduce the risk of electric shock or damage to the equipment:

Use an approved power cord. If you have questions about the type of power cord to use, contact your Hewlett Packard Enterprise authorized service provider. If you have not been provided with a power cord for your product or for any AC-powered option intended for your product, purchase a power cord that is approved for use in your country. You must use a power cord rated for your product and for the voltage and current marked on the electrical ratings label of the product. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product. Do not place objects on AC power cords or cables. Arrange them so that no one may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by the plug. Make sure that the total ampere rating of all products plugged into an extension cord or power strip does not exceed 80 percent of the ampere ratings limit for the extension cord or power strip. Precautions for power products 7 Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Power supplies Hot-plug power supplies are not designed to be removed or installed with AC power connected to the power supply. To reduce the risk of electric shock or damage to the equipment when handling hot-plug power supplies:

Install the power supply before connecting the power cord to the power supply. Unplug the power cord before removing the power supply from the product. If the system has multiple sources of power, you must unplug all AC power cords from the power supplies to completely disconnect power from the system. DC input power supplies do not connect directly to external bulk-level power systems

(48/60Vdc battery power). They must be connected to a local power distribution unit (PDU) that provides a dedicated output with suitable overcurrent protection for each power supply. The overcurrent protection (circuit breaker/pluggable fuse module) must be sized according to the input rating of each power supply. Refer to the documentation provided with the DC-powered system. Verify that the external power source connected to your product matches the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your Hewlett Packard Enterprise authorized service provider or local power company. Uninterruptible power supply (UPS) products To reduce the risk of electric shock and/or equipment damage when installing or servicing UPS products:

The installation of options and routine maintenance and service of UPS products must be performed by trained service technicians who are knowledgeable about the procedures, precautions, and hazards associated with AC power products. Hardwired UPS products require a direct connection to an AC branch circuit (AC mains). Connection should only be performed in accordance with National Electrical Code

(NFPA70) Article 310 in North America or the equivalent local and national wiring regulations. Use a Lockout/Tagout procedure to isolate hardwired UPS products from AC power before servicing the product or replacing a non-hot-plug component. Do not operate a UPS that is disconnected from AC power. Use the TEST/ALARM RESET button to test the batteries. Disconnect all protected loads before disconnecting the UPS from AC power. Pluggable UPS products must be disconnected and unplugged from AC power before servicing the product or replacing a non-hot-plug component. Do not overload the output of the UPS. The total connected load should not exceed the rated output. To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. If a large number of products will be connected to a single UPS, it may be necessary to conduct an evaluation of the installation to verify the total amount of leakage current. 8 Safety precautions The total combined leakage current should not exceed 5 percent of the input current for the UPS and associated load. For rack installations, do not exceed the maximum number of UPS products in any single equipment rack. For rack installations, install the UPS only at the bottom of a rack. To reduce the risk of personal injury or damage to equipment when installing a Remote Emergency Power Off (REPO) port:

The REPO port must be wired by a licensed electrician. Verify that the main AC power disconnect device for the UPS is locked and/or tagged in the OFF position before wiring the REPO port. In North America, the REPO circuit must comply with the NEC (NFPA 70, Article 725) for a Class 2 circuit. In other geographical regions or countries, the REPO port wiring must comply with the national and local standards in the area in which the product is installed. Remove watches, rings, or other metal objects prior to working with the equipment. To reduce the risk of personal injury from electric shock or damage to equipment when installing or servicing batteries:

Make sure that only trained service personnel handle or connect the batteries. On products with remote external batteries, do not attempt to replace batteries unless all battery circuit breakers are in the OFF (down) position. These are hazardous voltage batteries. Use tools with insulated handles. Do not disassemble, crush, or puncture the batteries. Do not attempt to recharge batteries after they have been removed from the equipment. This product may contain sealed lead-acid or lithium-ion batteries. To reduce the risk of fire or chemical burns:

Use only the Hewlett Packard Enterprise spare battery designated for this equipment. Do not expose the batteries to temperatures higher than 60C or dispose of in fire. Do not short the external contacts of the batteries. Do not immerse the batteries in water. Power distribution units (PDUs) To reduce the risk of electric shock and/or equipment damage when installing or servicing PDUs:

The installation and routine maintenance and service of PDUs must be performed by trained service technicians who are knowledgeable about the procedures, precautions, and hazards associated with AC power products. Hardwired PDUs require a direct connection to an AC branch circuit (AC mains). Connection should only be performed in accordance with National Electrical Code (NFPA70 Article 310) in North America, or in other regions or countries, in accordance with the equivalent local and national wiring regulations. Precautions for power products 9 A reliable grounded (earthed) connection should be checked before connecting PDUs. Use a Lockout/Tagout procedure to isolate hardwired PDUs from AC power before servicing or replacing the product. Pluggable PDUs must be disconnected from the product and unplugged from the AC electrical outlet before servicing or replacing the product. Permanently connected PDUs must be disconnected from the product and the external power source before servicing or replacing the product. Do not overload the output of PDUs. The total connected load should not exceed rated input power. To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. If a large number of products will be connected to a single PDU, it may be necessary to conduct an evaluation of the installation to verify the total amount of leakage current. The total combined leakage current should not exceed 5 percent of the input current for the PDU and associated load. Grounding Depending on the product model, your product will be classified either as a safety Class I or safety Class II-compliant device. Class I devices require a connection to earth ground (3-terminal plug); Class II devices incorporate a 2-terminal plug. Class I: There must be an uninterruptible safety earth ground from the main power source to the product's power cord or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored. Class II: Safety Class II-compliant devices include supplemental insulation to protect against electric shock, and do not require a connection to earth ground. For LAN connections:

If your LAN covers an area served by more than one power distribution system, be sure their safety grounds are securely interconnected. LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the electrical utilities power grid). Handle exposed metal components of the network with caution. This product and all interconnected equipment must be installed indoors within the same building, including all associated LAN connections as described by Environment A of the IEEE 802.3af standard. Earth leakage current To reduce the risk of electric shock due to high leakage currents, ensure that there is a reliable grounded (earthed) connection before connecting power distribution products to AC power. Observe the following limits when connecting the product to AC power distribution devices:

For UPS products and PDUs that have attached AC power cords or are directly wired to the building power, the total combined leakage current should not exceed 5 percent of the rated input current for the device. For UPS products and PDUs that have detachable AC power cords, the total combined leakage current should not exceed 3.5mA. 10 Safety precautions Electrostatic discharge (ESD) When handling any electronic component or assembly (such as a PCI card or memory DIMM), you must observe the following antistatic precautions to prevent damage. An ESD kit (Hewlett Packard Enterprise P/N A3024-80004) is available (or supplied with memory additions). This kit contains one wrist strap, one conductive sheet, and one antistatic foam pad. Always disconnect power from the server and wear a grounded wrist strap when working around the server. Always wear a grounded wrist strap when handling printed circuit boards. Treat all assemblies, components, and interface connections as static sensitive. Avoid working in carpeted areas and keep body movement to a minimum while removing or installing boards to minimize buildup of static charge. Voltage selection On products that have voltage select switches, make sure that the switch is set for the type of voltage you use (115 VAC or 230 VAC). Do not attempt to power the product with voltage converter kits sold for appliances. Batteries WARNING! Some Hewlett Packard Enterprise products may contain internal replaceable battery cells or battery packs. There is risk of fire, burns, or explosion if the battery pack is not handled properly. To reduce the risk of personal injury:

Do not attempt to recharge the battery. Do not disassemble, crush, puncture, short external contacts, or dispose of the battery in fire or water. Replace only with the Hewlett Packard Enterprise spare battery designated for this product. Dispose of used batteries according to the manufacturer's instructions and local disposal requirements. For battery holders (for example, coin cells), observe the correct polarity when changing the battery/cell. There is a danger of explosion if the battery is installed incorrectly. Precautions for power products 11 Fuse replacement CAUTION:

same type and the same rating. Disconnect power before changing fuses. For continued protection against risk of fire, replace fuses only with fuses of the 12 Safety precautions Precautions for products installed in racks and cabinets Materials handling To reduce the risk of personal injury or damage to the equipment:

Observe local occupational health and safety requirements and guidelines for handling materials. Obtain assistance to lift and stabilize the product during installation or removal. Remove all pluggable power supplies and modules to reduce the weight of the product. Be careful when pressing the rail release latches and sliding the product into the rack. The slide rails could pinch your fingertips. Rack stability To reduce the risk of personal injury or damage to the equipment, the rack must be secured adequately to prevent it from becoming unstable and/or falling over. Extend the leveling jacks to the floor. Ensure that the full weight of the rack rests on the leveling jacks. Install stabilizing feet on the rack. In a multiple-rack installation, fasten the racks together securely. Extend only one rack component at a time. Racks can become unstable if more than one component is extended. Load the rack from the bottom up, starting with the heaviest component. Ensure that the component is properly mated with the rails, or the rails may be unstable. Do not attempt to move a fully loaded rack. Remove components from the rack before moving it. Do not attempt to move a rack on an incline that is greater than 10 degrees from horizontal. Cabinet safety WARNING! Cabinets are heavy even when empty. Exercise caution when moving cabinets whether equipment is installed in the cabinet or not. Avoid rolling cabinets on rough or uneven surfaces or inclines greater than 10 degrees. Unloading cabinets from the pallet and movement of cabinets should be performed by at least two people. Slideable products are not to be extended from the cabinet while the equipment is on the shipping pallet. The cabinet must be unloaded from the pallet and all anti-tip devices properly installed prior to extending any slideable product. Once installed, all anti-tip devices must remain in place to maintain stability. Only one slideable product must be extended at a time. Failure to follow these precautions can result in damage to equipment or injury to personnel. Precautions for modems, telecommunications, or LAN options To reduce the risk of exposure to shock from telephone ringing voltages:

Do not connect or use a modem or telephone (other than a cordless type) during a lightning storm. Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. Do not connect or use a modem or telephone cable in a wet location. Precautions for products installed in racks and cabinets 13 Disconnect the modem cable from the wall socket before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack. Do not plug telecommunications or telephone connectors into the NIC receptacles. 14 Safety precautions 2 Environmental notices Hewlett Packard Enterprise is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hpe.com/info/reach. For Hewlett Packard Enterprise product environmental and safety information and compliance data, including RoHS and REACH, see http://www.hpe.com/info/ecodata. For Hewlett Packard Enterprise environmental information, including company programs, product recycling, and energy efficiency, see http://www.hpe.com/info/environment. Waste Electrical and Electronic Equipment (WEEE) Directive For details about the European Union (EU) WEEE Directive, see WEEE Information for Users or go to the website http://www.hpe.com/recycle. Battery replacement notices Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, use the public collection system or return them to Hewlett Packard Enterprise, an authorized Hewlett Packard Enterprise Partner, or their agents. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider. Waste Electrical and Electronic Equipment (WEEE) Directive 15 RoHS material content declarations China RoHS material content declaration Chinese version:

http://www8.hp.com/us/en/hpe/hp-information/livingprogress/environmentalprogress/

chinarohs.html English version:

http://www8.hp.com/us/en/hpe/hp-information/livingprogress/environmentalprogress/

chinarohs-english.html China RoHS Hazardous Substances table India RoHS material content declaration This product complies with the India E-waste (Management) Rules, 2016 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule II of the Rule. India RoHS quarterly declaration 16 Environmental notices Taiwan RoHS Hazardous Substances table Turkey RoHS material content declaration Ukraine RoHS material content declaration RoHS material content declarations 17 Perchlorate material Special handling may apply Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/

perchlorate/. This products real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California. 18 Environmental notices European Union Commission Regulation 1275/2008 The power data for affected productsincluding the power consumption of the product in networked standby if all wired network ports are connected and all wireless network ports are activatedis provided in section P14, Additional information, of the product IT ECO Declaration available at https://www.hpe.com/global/livingprogress/environmentalprogress/productdata/

iteconetworking_hpe.html. European Union Commission Regulation 1275/2008 19 3 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number is not the marketing name or model number of the product. Federal Communications Commission notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this product, go to the Hewlett Packard Enterprise Support Center website:

http://www.hpe.com/support/hpesc For questions regarding this FCC declaration, contact us by mail or telephone:

Hewlett Packard Enterprise 3000 Hanover Street Palo Alto, CA 94304 U.S. 1-281-514-3333 To identify the product, refer to the part, series, or model number found on the product. Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and B, depending upon their intended installation. Class A devices are those that may reasonably be expected to be installed in a business or commercial environment. Class B devices are those that may reasonably be expected to be installed in a residential environment (for example, personal computers). The FCC requires devices in both classes to bear a label indicating the interference potential of the device as well as additional operating instructions for the user. FCC rating label The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices have an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After you determine the class of the device, refer to the corresponding statement. Class A equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. 20 Regulatory compliance notices Class B equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modification The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett Packard Enterprise may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables (except for RJ-45 cables) with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Global notice for Class A equipment Operation of this equipment in a residential environment could cause radio interference. Notices for Canada (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CAN ICES-3(A)/NMB-3(A) Cet appareil numrique de la class A respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. CAN ICES-3(B)/NMB-3(B) Cet appareil numrique de la class B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Global notice for Class A equipment 21 Notices for China Class A equipment Trusted Platform Module (TPM) China Import Restrictions HEWLETT PACKARD ENTERPRISE SPECIAL REMINDER: Before enabling TPM functionality on this system, you must ensure that your intended use of TPM complies with relevant local laws, regulations and policies, and approvals or licenses must be obtained if applicable. For any compliance issues arising from your operation/usage of TPM which violates the above mentioned requirement, you shall bear all the liabilities wholly and solely. Hewlett Packard Enterprise will not be responsible for any related liabilities. Notices for European Union European Union Regulatory Notice Products bearing the CE marking comply with applicable EU Directives:

Compliance with such directives is assessed using applicable European Harmonised Standards. The Declaration of Conformity can be found at the website http://www.hpe.com/eu/certificates.

(Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) The point of contact for regulatory matters is HPE, Postfach 0001, 1122 Wien, Austria. Products with wireless functionality (EMF) This product meets the provisions of the EU's Council recommendation 1999/519/EC on the limitation of the exposure of the general public to electromagnetic fields (0 Hz to 300 GHz). This product may incorporate a radio transmitting and receiving device. For products with wireless functionality, a separation distance of 20 cm between the body of the user and the antenna ensures that the RF exposure levels comply with the EU requirements. Restrictions for product with wireless functionality For products with 5 GHz WLAN functionality: when operating in the frequency band 5150 to 5350 MHz, this product is restricted to indoor use only. 22 Regulatory compliance notices Notices for Japan VCCI notice Power cord statement Notices for Korea Class A equipment Class B equipment Notices for Japan 23 Notices for Taiwan BSMI notices Class A EMI warning message Battery replacement notice UPS (less than 16A output current) UPS (greater than 16A output current) 24 Regulatory compliance notices Belarus Kazakhstan Russia marking Manufacturer and Local Representative Information Manufacturer information:

Local representative information Russian:

Russia:

Hewlett Packard Enterprise Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S. Belarus:

Kazakhstan:

Local representative information Kazakh:

Russia:

Belarus:

Kazakhstan:

Manufacturing date:

The manufacturing date is defined by the serial number. CCSYWWZZZZ (serial number format for this product) Belarus Kazakhstan Russia marking 25 Valid date formats include:

YWW, where Y indicates the year counting from within each new decade, with 2000 as the starting point; for example, 238: 2 for 2002 and 38 for the week of September 9. In addition, 2010 is indicated by 0, 2011 by 1, 2012 by 2, 2013 by 3, and so forth. YYWW, where YY indicates the year, using a base year of 2000; for example, 0238: 02 for 2002 and 38 for the week of September 9. 26 Regulatory compliance notices Wireless devices In some environments, the use of wireless devices might be restricted. Such restrictions might apply on airplanes, in hospitals, near explosives, or in other hazardous locations. Before you turn on this product, be sure that you understand local policies and have proper authorization. WARNING! Exposure to Radio Frequency Radiation: The radiated output power of this device is below the FCC radio exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches) during normal operation. Brazilian notice Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Canadian notice Wireless operation is subject to two conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device. Japanese notice Mexican notice La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Wireless devices 27 Taiwanese notice 28 Regulatory compliance notices Laser compliance notices This device may contain a laser that is classified as a Class 1 Laser Product in accordance with U.S. FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. Each laser product complies with 21 CFR 1040.10 and 1040.11 (except for deviations pursuant to Laser Notice No. 50, dated May 27, 2001) and with IEC 60825-1. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only Hewlett Packard Enterprise Authorized Service technicians to repair the unit. Laser compliance notices 29 Index B batteries replacement notices, 15 safety precautions, 9, 11 Belarus Kazakhstan Russia EAC marking, 25 BSMI notices, 24 C cabinet safety, 13 CE compliance marking European Union Regulatory Notice, 22 China import restrictions Trusted Platform Module (TPM), 22 China RoHS Hazardous Substances table, 16 China RoHS material content declaration, 16 D Declaration of Conformity European Union Regulatory Notice, 22 E EAC marking Belarus Kazakhstan Russia, 25 earth leakage current, 10 electromagnetic interference (EMI) cable connector hoods, 21 electrostatic discharge (ESD), 11 EMC compliance notices, 20 EMF (electromagnetic fields) European Union Regulatory Notice, 22 environmental notices, 15 battery replacement and disposal, 15 European Union Commission Regulation 1275/2008, 19 perchlorate, 18 REACH, 15 RoHS, 15 WEEE, 15 equipment symbols, 5 ESD kit, 11 EuroAsian Economic Commission (EAC), 25 European Union Commission Regulation 1275/2008, 19 European Union Regulatory Notice CE compliance marking, 22 Declaration of Conformity, 22 products with wireless functionality (EMF), 22 F FCC notice, 20 FCC rating label, 20 Class A equipment, 20 Class B equipment, 21 fuse replacement, 12 G grounding 30 Index products installed in racks and cabinets, 13 earth leakage current, 10 ESD, 11 safety precautions, 10 L laser compliance notices, 29 M maintaining and servicing products safety precautions, 6 materials handling modems safety precautions, 13 P perchlorate material safety precautions, 18 power cords safety precautions, 7 power distribution units (PDUs) safety precautions, 9 power supplies safety precautions, 8 products installed in racks and cabinets materials handling, 13 safety precautions, 13 products with wireless functionality (EMF), 22 R rack stability, 13 radio frequency (RF) emission limits FCC notice, 20 radio frequency interference (RFI) cable connector hoods, 21 REACH, 15 recycling notices, 15 regulatory compliance identification numbers, 20 regulatory compliance notices, 20 BSMI, 24 Canada (Avis Canadien), 21 China, 22 European Union, 22 FCC, 20 global notice for Class A equipment, 21 identification numbers, 20 Japan, 23 Korea, 23 laser notices, 29 recycling notices, 15 Taiwan, 24 WEEE Directive, 15 wireless devices, 27 regulatory information Turkey RoHS material content declaration, 17 Ukraine RoHS material content declaration, 17 regulatory model number, 20 Remote Emergency Power Off (REPO) port safety precautions, 9 RoHS Hazardous Substances table RoHS material content declarations China, 16 Taiwan, 17 China, 16 S safety precautions, 5 batteries, 9, 11 cabinets, 13 fuse replacement, 12 general, 5 grounding, 10 maintaining and servicing products, 6 modems, 13 modems, telecommunications, or LAN options, 13 PDUs, 9 power cords, 7 power products, 7 power supplies, 8 products installed in racks and cabinets, 13 REPO port, 9 telecommunications equipment, 13 UPS, 8 voltage selection, 11 substances environmental notices, 15 perchlorate material, 18 RoHS material content declarations, 16 symbols on equipment, 5 T Taiwan RoHS Hazardous Substances table, 17 telecommunications equipment safety precautions, 13 Trusted Platform Module (TPM) China import restrictions, 22 Turkey RoHS material content declaration, 17 U Ukraine RoHS material content declaration, 17 UPS products safety precautions, 8 V VCCI notice, 23 voltage selection, 11 W WEEE Directive, 15 wireless devices, 27 Brazilian notice, 27 Canadian notice, 27 electromagnetic fields (EMF), 22 Japanese notice, 27 Mexican notice, 27 Taiwanese notice, 28 31