FCC ID: Q9DAPIN0314315 Aruba 310 Series Wireless Access Point

Aruba 310 Series Wireless Access Point Installation Guide The Aruba 310 Series Wireless Access Points support IEEE 802.11ac standards for a high-performance WLAN. This device is equipped with two single-band radios, which provide network access and monitor the network simultaneously. This access point to deliver high-performance 802.11n 2.4GHz and 802.11ac 5GHz functionality, while also supporting 802.11a/b/g wireless services. Multi-user Multiple-in, Multiple-output (MU-MIMO) is enabled when operating in 5GHz mode for optimal performance. The AP-314 and AP-315 access points work in conjunction with an Aruba controller, while IAP-314 and IAP-315 access points can be configured via built-in virtual controller. 310 Series wireless access points provides the following capabilities:

IEEE 802.11a/b/g/n/ac wireless access point IEEE 802.11a/b/g/n/ac wireless air monitor IEEE 802.11a/b/g/n/ac spectrum monitor Compatible with IEEE 802.3at and 802.3af PoE Support for MCS8 and MCS9 Centralized management, configuration and upgrades Integrated Bluetooth Low Energy (BLE) radio Package Contents

(I)AP-314 or (I)AP-315 access point 9/16" and 15/16 Ceiling Rail Adapters Safety, Compliance, and Warranty Information guide Aruba Instant Quick Start Guide (IAP-314 and IAP-315 only) Aruba Professional Installation Guide (IAP-314 only) Aruba 310 Series Wireless Access Point Installation Guide (this document) Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Software AP-314 and AP-315 access points require ArubaOS 6.5.0 or higher. For additional information, refer to the ArubaOS User Guide and ArubaOS Quick Start Guide. Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment meet all regulatory standards of their country/domain. For complete list of country-approved channels and devices, refer to the Aruba Downloadable Regulatory Table at www.arubanetworks.com. 310 Series Hardware Overview Figure 1 LED Status Indicators LEDs The 310 Series has two LEDs that indicate the system and radio status. The LEDs have three operating modes that can be selected in the system management software:

Default mode: see Table 1 Off mode: LEDs are off Blink mode: LEDs blink green Table 1: 310 Series LED Status Indicators Figure 3 USB Port LED Color/State Meaning System Status

(Left) Off Device powered off Green- blinking Device booting, not ready for use Green- solid Amber- solid Amber- blinking Green/Amber-

solid Red Off Device ready for use Device ready; Power Save mode (802.3af PoE) Device operating in restricted mode. Meets one of the following conditions:

Uplink negotiated in sub-optimal speed

(<1Gbps), or Ethernet radio is in non High-Throughput

(HT) mode No software setting/network restrictions System error condition Device powered off; or both radios disabled Green- solid Both radios enabled in access mode Green- blinking One radio enabled in access mode; other disabled Amber- solid Both radios enabled in monitor mode Amber- blinking One radio enabled in monitor mode; one radio disabled Alternating Green: one radio in access mode Amber: one radio in monitor mode Radio Status

(Right) External Antenna Connectors The (I)AP-314 access points are equipped with four external antenna connectors located on the front corners of the access point (see Figure 2). Figure 2 External Antenna Connectors ANT1 ANT2 ANT0 ANT3 Antennas ports ANT0 and ANT1 have dual band functionality and support both 2.4GHz and 5GHz, while ANT2 and ANT3 are single-band and support 5GHz only. External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. USB Interface The 310 Series is equipped with a USB port for connectivity with cellular modems and other USB client devices. When powered by an 802.3at or DC source, the USB port can supply power up to 5W. The USB interface is disabled when the access point is powered by an 802.3af PoE source. Figure 4 Back Panel USB Port Console Port Kensington Lock Ethernet Port DC Power Socket Reset Button Console Port The console port allows the user to connect the access point directly to a serial terminal or laptop for local management. Connect the device to a terminal or terminal server using an Ethernet cable. The port is a 4-pin HDR connector with pin-out details in Figure 5. Figure 5 Serial Port Pin-Out Pin Signal 1 3.3V 2 RX 3 TX 4 GND Ethernet Ports The 310 Series is equipped with a 100/1000Base-T auto-sensing MDI/MDX Ethernet port. This port supports wired-network connectivity, in addition to Power over Ethernet (PoE) from IEEE 802.3af and 802.3at compliant power sources. This device accepts 56V DC (802.3at), or 48V DC (802.3af) nominal as a standard powered device (PD) from power sourcing equipment, including PoE midspan injector or a PoE-sourcing network infrastructure. The port is an RJ45 connector, marked on the enclosure with 57V Figure 6 RJ45 Gigabit Port Pin-Out 600mA. 1000Base-T Gigabit Ethernet Port RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Signal Name BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

Function Bi-directional pair +A Bi-directional pair -A Bi-directional pair +B Bi-directional pair +C Bi-directional pair -C Bi-directional pair -B Bi-directional pair +D Bi-directional pair -D Kensington Lock Slot The 310 Series is equipped with a Kensington lock slot for additional security, shown in Figure 4. Reset Button The reset button can be used to return the access point to factory default settings. To reset the access point, refer to the steps below:

1. Power off the access point. 2. Press and hold the reset button using a small, narrow object, such as a paperclip. 3. Power-on the access point without releasing the reset button. The power LED will flash within 5 seconds. 4. Release the reset button. The power LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings. Power The Ethernet port supports PoE-in and may draw power from an 802.3at

(recommended) or an 802.3af source. If PoE is unavailable, the 310 Series access points have a single 12V/36W DC power input to support the AP-AC-V30B AC-to-DC power adapter kit (sold separately). When both 802.3at and DC power sources are available, the DC power source will take precedence. The Access point will simultaneously draw a minimal current from the PoE source. In the event that the DC source fails, the access point will switch to the 802.3at source. The 310 Series operates without restriction when powered by 802.3at compliant and DC power sources. In this mode the USB interface is enabled and supports up to 1A/5W to a powered device (PD). When powered by an 802.3af PoE source, the access point operates in power-saving mode. In this mode the USB interface is disabled. Table 2: Power Modes Power Source Limitations USB Output DC (AP-AC-12V30B) No restrictions PoE 802.3at PoE 802.3af No restrictions USB disabled Before You Begin 1A/5W 1A/5W Disabled FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Aruba Instant User Guide for details on restrictions. Produit rseau local radio basse puissance operant dans la bande frquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions. Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlglich Einschrnkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide. Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni. Access Point Pre-Installation Checklist Before installing your 310 Series access point, ensure that you have the following:

CAT5E UTP cable or better One of the following power sources:

IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The PoE source can be any power source equipment (PSE) controller or midspan PSE device Aruba AP-AC-12V30UN adapter kit (sold separately) For AP-314 and AP-315 access points only:

Aruba controller provisioned on the network:

Layer 2/3 network connectivity to your access point One of the following network services:

Aruba Discovery Protocol (ADP) DNS server with an A record DHCP Server with vendor-specific options. Figure 7 Attaching the Ceiling Rail Adapter Aruba Networks, Inc., in compliance with governmental requirements, has designed the 310 Series access points so that only authorized network administrators can change the settings. For more information about access point configuration, refer to the ArubaOS Quick Start Guide/

Aruba Instant Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide. Verifying Pre-Installation Connectivity The instructions for this section are applicable to the AP-314 and AP-315 only. Before installing access points in a network environment, make sure that they are able to locate and connect to the controller after power on. Specifically, you must verify the following conditions:

When connected to the network, each access point is assigned a valid IP address Access points are able to locate the controller Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. Pre-Installation Network Requirements After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed. For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller. Identifying Specific Installation Locations You can mount the 310 Series access point to a wall or on the ceiling. Use the access point placement map generated by Arubas RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. Examples of sources that degrade RF performance include:

Cement and brick Objects that contain water Metal Microwave ovens Wireless phones and headsets Installing the Access Point Refer to the following steps to install your Aruba 310 Series access point using the AP Ceiling Rail Mount Kit (AP-220-MNT-C1). Using the Ceiling Rail Adapter The 310 Series access point ships with two ceiling rail adapters for 9/16 and 15/16 ceiling rails. Additional wall mount adapters and ceiling rail adapters for other rail styles are available as accessory kits. This device must be professionally installed and serviced by an ACMP or other Aruba-certified technician. The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure to properly install this product may result in physical injury and/or damage to property. 1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed. 2. Place the adapter against the back of the access point with the adapter at an angle of approximately 30 degrees to the tabs (see Figure 7). 3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7). 4. If necessary, connect the console cable to the console port on the back of the access point. 5. Hold the access point next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail

(see Figure 8). Make sure that any cable slack is above the ceiling tile. 6. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail. Figure 8 Mounting the Access Point 7. On the (I)AP-314, install the external antennas according to the manufacturers instructions, and connect the antennas to the antenna interfaces on the access point. Connecting Required Cables Install cables in accordance with all applicable local and national regulations and practices. Verifying Post-Installation Connectivity The integrated LEDs on the access point can be used to verify that the device is receiving power and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Configuring the 310 Series The instructions for the following section are applicable to AP-314 and AP-

315 model access points only. Access Point Provisioning/Reprovisioning Provisioning parameters are unique to each access point. These local access point parameters are initially configured on the controller which are then pushed out to the access points and stored on the devices. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details. Access Point Configuration Configuration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the access points, but remain stored on the controller. Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to their respective guides for further details: the ArubaOS User Guide. Aruba 310 Series Wireless Access Point Installation Guide a Hewlett Packard Enterprise company Contacting Aruba Networks Web Support Main Site Support Site http://www.arubanetworks.com https://support.arubanetworks.com Airheads Social Forums and Knowledge Base http://www.community.arubanetworks.com North American Telephone International Telephones Software Licensing Site End-of-life Information 1-800-943-4526 (Toll Free) 1-408-754-1200 http://www.arubanetworks.com/support-services/

aruba-support-program/contact-support/

http://licensing.arubanetworks.com http://www.arubanetworks.com/support-services/end-

of-life/

Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-services/

security-bulletins/

Support Email Addresses Americas, EMEA and APAC support@arubanetworks.com Security Incident Response Team (SIRT) Email sirt@arubanetworks.com Copyright Copyright 2016 Hewlett Packard Enterprise Development LP Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source Warranty This hardware product is protected by an Aruba warranty. For details, see the Safety, Compliance, and Warranty Information Guide included with this device. a Hewlett Packard Enterprise company www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 Aruba 310 Series Wireless Access Point | Installation Guide Part Number 0511871-02 | January 2016

Aruba 310 Series Wireless Access Point Regulatory Compliance and Safety Information Guide Introduction This document contains domestic and international regulatory compliance and safety information for 310 Series access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below. Electrical and Environmental Specifications Regulatory Information Proper Disposal of Aruba Equipment Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/

safety_addendum. All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Tous les points d'accs Aruba doivent imprativement tre installs par un professionnel agr. Ce dernier doit s'assurer que l'appareil est mis la terre et que le circuit de mise la terre est conforme aux codes lectriques nationaux en vigueur. Electrical Ethernet:

100/1000 Base-T auto-sensing Ethernet RJ45 interface IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T) Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum). Power:

48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36B) Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC) If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an output rated 48VDC, minimum 2A, marked LPS and Class 2, and suitable for plugging into a standard power receptacle in the US and Canada. Environmental Operating:

Temperature: 0C to +50C (+32F to +122F) Humidity: 5% to 93% non-condensing Storage and transport:

Temperature: -40C to +70C (40F to +158F) Regulatory Information The following regulatory model names apply to the 310 Series access points:

AP-314/IAP-314: APIN0314 AP-315/IAP-315: APIN0315 0511872-01 | January 2016 1 Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 10.63 inches (27cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Dclaration sur les limites d'exposition aux radiofrquences : cet quipement est conforme aux limites d'exposition aux rayonnements radiolectriques spcifies par la FCC. Il doit tre install et utilis une distance minimale de 27 cm par rapport votre corps pour les frquences de 2,4 et 5 GHz. Cet metteur-rcepteur ne doit pas tre utilis ou situ proximit d'autres antennes ou metteurs-rcepteurs. En cas d'utilisation dans la plage de frquences de 5,15 5,25 GHz, cet appareil doit uniquement tre utilis en intrieur afin de rduire les risques d'interfrence avec les systmes satellites mobiles partageant le mme canal. FCC Class B Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. Operation is subject to the following conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Toute modification effectue sur cet quipement sans l'autorisation expresse de la partie responsable de la conformit est susceptible d'annuler son droit d'utilisation. Canada Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Dclaration dIndustrie Canada Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Conformment aux rglementations dIndustrie Canada, cet metteur-rcepteur radio doit tre utilis uniquement avec une antenne dont le type et le gain maximal doivent tre approuvs par Industrie Canada. Pour rduire les interfrences radio 2 Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide potentielles, le type dantenne et son gain doivent tre choisis de faon ce que la puissance isotrope rayonne quivalente

(PIRE) ne dpasse pas les valeurs ncessaires une communication efficace. Ce priphrique est conforme aux rglements RSS exempts de licence dIndustrie Canada. Lutilisation de ce priphrique est soumise aux deux conditions suivantes : (1) ce priphrique ne doit pas provoquer dinterfrences, et (2) ce priphrique doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un dysfonctionnement. EU Regulatory Conformance Aruba Networks Inc., hereby declares that Aruba 310 Series access points are in compliance with directives listed below:

EMC Directive 2004 Low Voltage Directive 2006 R&TTE Directive 1999 REACH Regulation (EC) No.: 1907/2006 RoHS Directive 2011 WEEE Directive 2002 A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval.

Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device. Proper Disposal of Aruba Equipment Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). India RoHS This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India. European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC

(RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this directive. Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 3 China RoHS 10 Aruba products also comply with China environmental declaration requirements and are labeled with the EFUP 10 label shown at the left.

Hazardous Materials Declaration

(Hazardous Substance)

(Parts)

(PCA Boards)

(Mechanical Sub-Assemblies)

SJ/T11363-2006

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.

This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product.

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. Copyright 2016 Hewlett Packard Enterprise Development LP 4 Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide a Hewlett Packard Enterprise company www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax: 408.227.4550