This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
This device may not cause interference This device must accept any interference, including interference that may cause undesired operation of the device. Proper Disposal of Aruba Equipment Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left
(crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). The BT-100 device is designed to be used with Analytics and Location Engine
(ALE) and improve location monitoring. The key features are:
Better proximity performance than WiFi Operates as a stand-alone device Low power consumption Only three channels (37, 38 and 39) for advertisement for sending beacons 4. Align the 2 key slot style holes in the back of the unit against the 2 studs on the mounting bracket. Pull the unit down until it is locked in. Activation To activate the BT-100 device, pull out the tab that extends out of the bottom of the device. Package Contents BT-100 device Mylar tab Mounting bracket BT-100 The following figure show the top view of a BT-100 device Figure 1 BT-100 Top View The following figure shows the bottom view of the BT-100 device:
Figure 2 BT-100 Bottom View Wall Mounting Installation The mounting brackets is used for wall mounting a BT-100. Required Tools and Equipment The following tools and equipment are required for installing BT-100 on a wall:
Mounting Bracket (included in the kit) Wall Mounting Screws: The type of screw depends on the installation surface
(not included in the kit) Suitable Screwdrivers for all screw types (not included in the kit) Installation Steps To install a BT-100 device on a wall:
1. After you have chosen a mounting location, mark the location on the wall where you intend to make a mounting hole. The mounting location must be at least 12 feet above the floor. 2. Align the mounting bracket hole with the hole you created in the wall . 3. Use an appropriate screw to secure the BT-100. Product Specifications Physical Device dimensions (HxWxL): 16 mm x 47 mm x 47 mm Electrical Power Supply: Two standard coin battery (approximately 1460 days) Coin battery capacity: 2000 mAh Voltage: 3 V RF Performance Tx = -23 dBm to 0 dBm (23 dB dynamic range) Rx sensitivity = Approximately -94 dBm (1 Mbps) Working Frequency range: 2450 50 MHz Operation temperature: 0 C to 50 C Safety and Regulatory Compliance Aruba Networks provides a multi-language document that contains country-
specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model Names The regulatory model name applicable to the BT-100 device is ARBT0100. RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission
(FCC) Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Changes or modifications that are not explicitly approved by the party responsible for compliance with the FCC Rules could void the users authority to operate this equipment. WARNING Canada Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Beta Release: send comments to dl-techpub@arubanetworks Bluetooth Low Energy Device Hardware Guide Contacting Aruba Networks Web Support Main Site Support Site http://www.arubanetworks.com https://support.arubanetworks.com Airheads Social Forums and Knowledge Base community.arubanetworks.com North American Telephone International Telephones 1-800-943-4526 (Toll Free) 1-408-754-1200 arubanetworks.com/support-services/aruba-support-
program/contact-support/
Software Licensing Site licensing.arubanetworks.com/login.php Wireless Security Incident Response Team (WSIRT) Support Email Addresses arubanetworks.com/support/wsirt.php Americas and APAC support@arubanetworks.com EMEA emea.support@arubanetworks.com Americas and APAC Support Email support@arubanetworks.com WSIRT Email Please email details of any security problem found in an Aruba product. wsirt@arubanetworks.com Copyright 2013 Aruba Networks, Inc. AirWave, Aruba Networks, Aruba Mobility Management System, Bluescanner, For Wireless That Works, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners. Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. Warranty This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty terms and conditions. www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax 408.227.4550 Bluetooth Low Energy Device | Hardware Guide Part Number | April 2014