Aruba APM-210 Wireless Access Point Module Regulatory Compliance and Safety Information User Guide Introduction This document contains domestic and international regulatory compliance and safety information for the access point module. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below. Electrical and Environmental Specifications on page 1 Proper Disposal of Aruba Equipment on page 1
Safety and Regulatory Compliance on page 2 Electrical and Environmental Specifications Ethernet:
o 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface o MDI/MDX o o Power over Ethernet (IEEE 802.3at and 802.3af compliant), 48V DC (nominal) and 56V DC IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
(maximum)/350mA (see Power: o 48 VDC power interface, supports powering through an AC-to-DC power adapter o POE support on Ethernet ports: 802.3at-compliant and 802.3af-compliant POE sourcing devices o Connect Only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources. Environmental o Operating:Temperature:
o 0 C to +50 C (+32 F to +122 F) o Humidity: 5% to 95% non-condensing o Temperature: -40 C to +70 C (-40 F to +158 F) o Storage and transportation: For additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com Proper Disposal of Aruba Equipment
Dispose of Aruba products per local regulations. For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Safety and Regulatory Compliance Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model Names The following regulatory model names apply:
o APINM210 FCC The host device label is required to state the following:
Contains FCC ID: Q9DAPINM210 Contains IC: 4675A-APINM210 The following Caution statement is required in the user manual:
FCC Class B Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. Operation is subject to the following conditions:
o This device may not cause harmful interference. o This device must accept any interference received, including interference that may cause undesired operation
If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: Increase these parathion between the equipment and receiver. o Reorient or relocate the receiving antenna. o o Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio or TV technician for help.
Canada Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. For indoor use only. Operation in an outdoor host is prohibited. This radio transmitter APINM210 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The module as been approved with a Clip-On PCB Antenna.The Antenna is encased in a mold design specific for this module. The Maximum permissible antenna gain for 2.4GHz is 2.5dBi and 3.0dBi for 5GHz, and the antenna impedance is 50 ohms. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650- 5850
MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Dclaration dIndustrie Canada
Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Ce priphrique est conforme aux rglements RSS exempts de licence dIndustrie Canada. Lutilisation de ce priphrique est soumise aux deux conditions suivantes : (1) ce priphrique ne doit pas provoquer dinterfrences, et
(2) ce priphrique doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un dysfonctionnement. Pour une utilisation en intrieur uniquement. Opration dans un hte extrieur est interdite. Cet metteur APINM210 radio a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous avec le gain maximal admissible et de l'impdance d'antenne requise pour chaque type d'antenne indiqu. types d'antennes non inclus dans cette liste, ayant un gain suprieur au gain maximum indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Le module t approuv avec un clip-antenne PCB. L'antenne est enferm dans une conception de moule spcifique pour ce module. Le gain d'antenne maximale admissible pour 2.4GHz est de 2,5 dBi et 3.0dBi pour 5GHz, et l'impdance de l'antenne est de 50 ohms. Les utilisateurs sont informs que les radars haute puissance sont dsigns comme utilisateurs principaux des bandes 5250-5350MHz et 5650-5850MHz et ces radars pourraient provoquer des interfrences et / ou endommager les priphriques WLAN Exempts sous licence . EU Regulatory Conformance Aruba Networks Inc., hereby declares that the 320 Series Wireless Access Points are in compliance with directives listed below:
o EMC Directive: 2014/30/EU o Low Voltage Directive: 2014/35/EU o R&TTE Directive: 1999/5/EC o REACH Regulation (EC): 1907/2006 o RoHS Directive: 2011/65/EU o WEEE Directive: 2012/19/EU A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650- 5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval.
, ,
;
, ,
,