APIN0314315 Aruba 310 Series Wireless Access Point User Manual pt 2

 

Aruba 310 Series Wireless Access Point Regulatory Compliance and Safety Information Guide Introduction This document contains domestic and international regulatory compliance and safety information for 310 Series access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below. Electrical and Environmental Specifications Regulatory Information Proper Disposal of Aruba Equipment Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/

safety_addendum. All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Tous les points d'accs Aruba doivent imprativement tre installs par un professionnel agr. Ce dernier doit s'assurer que l'appareil est mis la terre et que le circuit de mise la terre est conforme aux codes lectriques nationaux en vigueur. Electrical Ethernet:

100/1000 Base-T auto-sensing Ethernet RJ45 interface IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T) Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum). Power:

48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36B) Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC) If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an output rated 48VDC, minimum 2A, marked LPS and Class 2, and suitable for plugging into a standard power receptacle in the US and Canada. Environmental Operating:

Temperature: 0C to +50C (+32F to +122F) Humidity: 5% to 93% non-condensing Storage and transport:

Temperature: -40C to +70C (40F to +158F) Regulatory Information The following regulatory model names apply to the 310 Series access points:

AP-314/IAP-314: APIN0314 AP-315/IAP-315: APIN0315 0511872-01 | January 2016 1 Aruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 10.63 inches (27cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Dclaration sur les limites d'exposition aux radiofrquences : cet quipement est conforme aux limites d'exposition aux rayonnements radiolectriques spcifies par la FCC. Il doit tre install et utilis une distance minimale de 27 cm par rapport votre corps pour les frquences de 2,4 et 5 GHz. Cet metteur-rcepteur ne doit pas tre utilis ou situ proximit d'autres antennes ou metteurs-rcepteurs. En cas d'utilisation dans la plage de frquences de 5,15 5,25 GHz, cet appareil doit uniquement tre utilis en intrieur afin de rduire les risques d'interfrence avec les systmes satellites mobiles partageant le mme canal. FCC Class B Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. Operation is subject to the following conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Toute modification effectue sur cet quipement sans l'autorisation expresse de la partie responsable de la conformit est susceptible d'annuler son droit d'utilisation. Canada Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Dclaration dIndustrie Canada Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Conformment aux rglementations dIndustrie Canada, cet metteur-rcepteur radio doit tre utilis uniquement avec une antenne dont le type et le gain maximal doivent tre approuvs par Industrie Canada. Pour rduire les interfrences radio 2 Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide potentielles, le type dantenne et son gain doivent tre choisis de faon ce que la puissance isotrope rayonne quivalente

(PIRE) ne dpasse pas les valeurs ncessaires une communication efficace. Ce priphrique est conforme aux rglements RSS exempts de licence dIndustrie Canada. Lutilisation de ce priphrique est soumise aux deux conditions suivantes : (1) ce priphrique ne doit pas provoquer dinterfrences, et (2) ce priphrique doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un dysfonctionnement. EU Regulatory Conformance Aruba Networks Inc., hereby declares that Aruba 310 Series access points are in compliance with directives listed below:

EMC Directive 2004 Low Voltage Directive 2006 R&TTE Directive 1999 REACH Regulation (EC) No.: 1907/2006 RoHS Directive 2011 WEEE Directive 2002 A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval.

Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device. Proper Disposal of Aruba Equipment Dispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). India RoHS This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India. European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC

(RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this directive. Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 3 China RoHS 10 Aruba products also comply with China environmental declaration requirements and are labeled with the EFUP 10 label shown at the left.

Hazardous Materials Declaration

(Hazardous Substance)

(Parts)

(PCA Boards)

(Mechanical Sub-Assemblies)

SJ/T11363-2006

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.

This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product.

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. Copyright 2016 Hewlett Packard Enterprise Development LP 4 Aruba 310 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide a Hewlett Packard Enterprise company www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.4500 Fax: 408.227.4550