LS-100 IG Rev 01.fm Page 1 Wednesday, December 17, 2014 11:11 AM LS-100 Wireless Location Sensor Installation Guide The Aruba LS-100 wireless location sensor is a single radio, dual-band WLAN device that scans the supported radio bands, collects relevant data about wireless devices in the network, and makes this information available to a locationing server by periodically connecting to the wireless network as a client device. In addition to WLAN scanning to improve infrastructure based locationing performance, the LS-100 also incorporates a Bluetooth Low Energy
(Bluetooth 4.0, BLE) chirper to support client based locationing services. Reset/LED Button The Reset/LED button is a dual-function push button, for system reset
(during power on) and LED control (during normal operation). To reset LS-100 to manufacturing defaults the button has to be held down (for several seconds) while the unit is powered on. During normal operation, the button can be used to toggle LED mode between normal (default after power on) and all off. Figure 3 LS-100 Rear Installing the Device Figure 6 Routing the USB Cable Service to all Aruba Networks products should be performed by trained service personnel only. N O T E The LS-100 device can be either plugged into an AC power outlet or mounted on a wall (powered via USB). Plugging LS-100 into an AC Power Outlet 1.
(Optional) You can keep your LS-100 device secure with the security kit. a. Align the triangle mark on the AC outlet security kit with the same triangle mark on the back panel of the LS-100. Console Port b. Rotate the security kit 180 degrees. Figure 4 Installing Security Kit 2. Attach the wall mount bracket to the wall. a. Use the wall mount bracket as the template to mark the two mounting points on the wall. Package Contents LS-100 wireless location sensor AC Power Plug USB Power Cable (Type A to type Micro-B connectors) 1m length AC Outlet Security Kit Wall Mount Bracket Release Key Aruba SW License Agreement (EULA) Installation guide (this document) Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. N O T E LS-100 Hardware Overview Figure 1 LS-100 Front Console Port The serial console port allows you to connect the device to a serial terminal or a laptop for direct local management. This port located at the rear of the LS-100 is a 4-pin connector covered by a dust cover. An optional serial adapter cable (AP-CBL-SER) is available for use with the LS-100 and is sold separately. Hot-plug operation is not recommended for the console port. System LED Before You Begin 2. Slide the AC power plug to the tracks at the back panel of the LS-100 until the plug locks into place. Figure 5 Installing AC Power Plug LED Table 1 LED Meanings LED System Status LED Color/State Off Red Red - Flashing Green - Flashing Green - Steady Amber - Flashing Amber - Steady Meaning Device powered off Error condition Device booting, not ready Device ready, not connected to network, configured Device ready, connected to network, configured Device ready, not connected to network, not configured Device ready, connected to network, not configured Figure 2 LS-100 Bottom Reset/LED Button Power Button USB USB Interface The LS-100 implements a Micro-B type USB interface for DC powering. Power Button The power button allows you to enable/disable DC power to all circuits (AC power may remain active at all times). FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide for details on restrictions. Produit rseau local radio basse puissance operant dans la bande frquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les details des restrictions. Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlglich Einschrnkungen finden Sie im ArubaOS User Guide. Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle restrizioni. To meet regulatory restrictions, the device must be professionally installed.
!
!
!
Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Examples of sources that degrade RF performance include:
Cement and brick Objects that contain water Metal Microwave ovens Wireless phones and headsets 3. After plugging the LS-100 into an AC power outlet, you can use a screw to secure the security kit to the wall.
!
Avoid hitting a live wire when drilling into a wall to secure the security kit. Mounting LS-100 on a Wall (Powered via USB) 1. Route the USB cable through the bottom opening of the wall mount bracket. b. Use a drill to create two holes on the two markings you created in the previous step. Install any necessary wall anchors. Wall anchors are not included in the package. d. Align the screw holes in the wall mount bracket with the previously installed anchors or demarcated screw points. Insert the screws to secure the wall mount bracket. Screws are not included in the package. c. e. Figure 7 Attaching the Wall Mount Bracket to a Wall 3. Align the tracks at the back panel of the LS-100 with the wall mount bracket. Push the LS-100 against the wall mount bracket and downward until the LS-100 locks into place. Figure 8 Attaching LS-100 to the Wall Mount Bracket LS-100 IG Rev 01.fm Page 2 Wednesday, December 17, 2014 11:11 AM Removing the LS-100 from the Wall Mount Bracket 1. To remove the LS-100 device from the wall mount bracket, begin by inserting the release key into the holes. 2. Use the release key to depress the tab on the LS-100 and push the device up. Figure 9 Removing LS-100 from the Wall Mount Bracket Verifying Post-Installation Connectivity The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Product Specifications Electrical Power Consumption:
DC (USB): not exceeding 2.25W AC: not exceeding 5W Supported Input AC Voltage Range: 90V to 265V Supported Input AC Frequency range: 47Hz to 63Hz Environmental Operating Temperature: 0C to 50C (32F to 122F) For additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com. Proper Disposal of Aruba Equipment For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com. Waste of Electrical and Electronic Equipment Aruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). European Union RoHS Aruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7
(Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the RoHS label shown at the left indicating conformance to this Directive. China RoHS 10 Aruba products also comply with China environmental declaration requirements and are labeled with the EFUP 10 label shown at the left. Safety and Regulatory Compliance Aruba Networks provides a multi-language document that contains country-
specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model Names The following regulatory model name apply to the LS-100:
LS-100: LSIN0100 FCC This device is electronically labeled. To view the FCC ID:
1. Log into the controller WebUI. 2. Navigate to Maintenance > Controller > About.
!
!
RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF Radiation Exposure Statement: When operated in the 5.15 to 5.25 GHz and 5.47 to 5.725 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-
channel Mobile Satellite Systems. FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
!
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturers instructions, may cause interference harmful to radio communications. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-
003 of Industry Canada. Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. EU Regulatory Conformance This product is CE marked according to the provisions of the R &
TTE Directive (1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0103 device model is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC -CE(!) The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the following location: http://support.arubanetworks.com Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices. Canadian Statement Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. LS-100 Wireless Location Sensor Installation Guide Contacting Aruba Networks Web Support Main Site Support Site Airheads Social Forums and Knowledge Base North American Telephone International Telephones Software Licensing Site Wireless Security Incident Response Team (WSIRT) Support Email Addresses Americas, APAC and EMEA WSIRT Email Please email details of any security problem found in an Aruba product. http://www.arubanetworks.com https://support.arubanetworks.com community.arubanetworks.com 1-800-943-4526 (Toll Free) 1-408-754-1200 arubanetworks.com/support-services/aruba-support-
program/contact-support/
licensing.arubanetworks.com/login.php arubanetworks.com/support/wsirt.php support@arubanetworks.com sirt@arubanetworks.com Copyright 2014 Aruba Networks, Inc. AirWave, Aruba Networks, Aruba Mobility Management System, Bluescanner, For Wireless That Works, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners. Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. Warranty This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty terms and conditions. www.arubanetworks.com 1344 Crossman Avenue Sunnyvale, California 94089 Phone: 408.227.45000511739-01 Fax 408.227.4550 LS-100 Wireless Location Sensor | Installation Guide Part Number 0511739-01 | December 2014