W2Y WIFI Module User manual

PRODUCT SPECIFICATION Version 1.0 WIFI Module Model Number: W2YM2510

(MT7603UN) Custom Approval Section Custom Name Department Approval Date DESIGN CHECK APPROVAL 2018/10/23 2018/10/23 2018/10/23 HUIZHOU GAOSHENGDA TECHNOLOGY CO., LTD 75 HUA YU RD., NO.75, ZHONGKAI HIGH-TECH DEVELOPMENT AREA, HUIZHOU, CHINA TEL07522096628 E-mail lims@gaosd.com PRODUCTS SPECIFICATION W2YM2510 Revision Document revision history Date Approved by Remarks Version 1.0 2018-10-23 Draft PAGE 2 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 1. General Description W2YM2510 is to specify the product requirements for 802.11b/g/n USB Module. This Card is based on MTK MT7603UN chipset that complied with IEEE 802.11n,and it is also backward complied with IEEE 802.11b/g standard from 2.4~2.5GHz.It can be used to provide up to 54Mbps for IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11b/g/n USB Module offers absolute interoperability with different vendors 802.11b/g/n Access Points through the wireless LAN. 2. Features Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate. Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate. Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate. Operation at 2.4~2.5GHz frequency band to meet worldwide regulations Supports WEP,802.1x,WPA and WPA2 enhanced security Friendly user configuration and diagnostic utilities Drivers support Windows 2000,Windows 7 and XP, Linux , Android High speed USB 2.0 interface ROHS compliant PAGE 3 OF 10 Version 1.0 PRODUCTS SPECIFICATION 3. Application Diagrams W2YM2510 3.2.1.2 3.1.1 IEEE 802.11b Section 3.2.1.1 3.1 General Requirements Feature Standard Radio and Modulation Schemes Operating Frequency Channel Numbers Data Rate 3.2.1.4 3.2.1.5 3.2.1.6 Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 3.2.1.3 3.2.1.7 3.2.1.8 Detailed Description IEEE 802.11b DQPSK , DBPSK and CCK with DSSS 2400 2483.5MHz ISM band 13 channels for Worldwide at most 11Mbps CSMA/CA with ACK Typical RF Output Power at each RF chain, and at room Temp 25 172 dBm at 11Mbps Typical Sensitivity at each RF chain. @Frame (1000-byte PDUs) Error Rate<8% at room Temp 25

-83 dBm for 11Mbps PAGE 4 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 Detailed Description IEEE 802.11g QPSK , BPSK , 16QAM ,64QAM with OFDM 2400 2483.5MHz ISM band 13 channels for Worldwide at most 54Mbps CSMA/CA with ACK Typical RF Output Power at each RF chain, at room Temp. 25 132 dBm at 54Mbps Typical Sensitivity at each RF chain. @Frame (1000-byte PDUs) Error Rate<10% at room Temp 25

-71 dBm at 54Mbps 3.1.2 IEEE 802.11g Section 3.2.2.1 3.2.2.2 Feature Standard Radio and Modulation Type Operating Frequency Channel Numbers Data Rate 3.2.2.3 3.2.2.4 3.2.2.5 3.2.2.6 Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 3.2.2.7 3.2.2.8 3.1.3 IEEE 802.11n Section 3.2.3.1 3.2.3.2 Feature Standard Radio and Modulation Type Operating Frequency Data Rate 3.2.3.3 3.2.3.4 3.2.3.5 Media Access Protocol 3.2.3.6 Transmitter Output Power at Antenna Connector 3.2.3.7 Receiver Sensitivity at Antenna Connector Detailed Description IEEE 802.11n BPSK , QPSK , 16QAM ,64QAM with OFDM 2400 ~ 2483.5MHz for ISM band at most 300 Mbps CSMA/CA with ACK Typical RF Output Power at each RF chain, and at room Temp. 25 2.4GHz Band/HT40 132dBm at MCS7 2.4GHz Band/HT20 152dBm at MCS7 Typical Sensitivity at each RF chain. @Frame(1000-byte PDUs)Error Rate=10% and at room Temp. 25 2.4GHz Band/HT20

-68dBm at MCS7 2.4GHz Band/HT40

-66dBm at MCS7 PAGE 5 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 4. Electrical and Thermal Characteristics 4.1 Temperature Limit Ratings Parameter Storage Temperature Ambient Operating Temperature Junction Temperature 4.2 General Section 4.2.1 4.2.2 4.2.3 4.2.4 Feature Antenna Type Operating Voltage Current Consumption USB Minimum Maximum

-40 0 0

+80 60 125 Units Detailed Description PIFA antenna 5V10%

450 mA at continuous transmit mode High Speed USB2.0 Interface 4.3 Software Driver Security Windows , Linux , Android 64/128-bits WEP, WPA, WPA2 4.4EEPROM Information Reg Domain Vendor ID Product ID Worldwide 2.4G Read from registryControl by driver Offset 0x39 for 2.4G:0xFF 0x0E8D 0x7603 PAGE 6 OF 10 Version 1.0 PRODUCTS SPECIFICATION 5. Mechanical Characteristics 5.1 Mechanical Requirements 4.4.1 4.4.2 4.4.3 Feature Length Width Height Detailed Description 70mm 45mm 1.6mm(PCB) 5.2 Mechanical Dimensions W2YM2510 PAGE 7 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 Size error range:

DIM

(MM) 0-5 5-10 10-50 Tolerance

(MM) 0.15 0.20 0.30 5.3 Pin Description Pin Definit 1 VCC 2 VCC 3 4 GND D-

5 NC 6 D+

ion

(5V)

(5V) 7 WL_Host_Wake

(Internal pull-up 10K Ohm) 8 GND 9 NC 10 Reset

(Internal pull-up 10K Ohm) PAGE 8 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 Appendix : Connector PAGE 9 OF 10 Version 1.0 PRODUCTS SPECIFICATION W2YM2510 mode PAGE 10 OF 10 Version 1.0 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If power exceeds the limit and the distanceOver 20cm distance in actual use between the device and user is compliant with the requirement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular be installed in TV device. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID: 2AC23-W2Y Or Contains FCC ID: 2AC23-W2Y when the module is installed inside another device, the user manual of this device must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and user. 2) The transmitter module may not be co-located with any other transmitter or antenna. Module Antenna Type: Integral Antenna, ANT Gain: 2dBi IC Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Le prsent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement CE Statement Herby, Hui Zhou Gaoshengda Technology Co., LTD declares that this WIFI ModuleW2YM2510 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states. Use the WIFI Module in the environment with the temperature between 0 and 60 Operation Frequency: 2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20)) 2422MHz~2462MHz (802.11n(HT40)) Max output power: WIFI: 0.0697W ManufacturerHui Zhou Gaoshengda Technology Co., LTD AddressNO.75 Zhongkai Development Area, Huizhou, Guangdong, China Tel: +86-0752-209669 Fax: +86-0752-2096698 E-mail: guanh@gaosd.cn