submitted | available | document details (if available) | source link |
---|---|---|---|
April 07 2016 | July 07 2016 | 产品规格书 zy Microsoft® Office Word 2007 |
various | User Manual | Users Manual | 994.31 KiB | April 07 2016 / July 07 2016 |
PRODUCT SPECIFICATION Version 1.3 IEEE 802.11 a/b/g/n/ac 2T/2R Dual Band Module Model Number: WC0DR2611 HUIZHOU GAOSHENGDA TECHNOLOGY CO.,LTD HUA YU RD., NO.75, ZHONGKAI HIGH-TECH DEVELOPMENT AREA, HUIZHOU, CHINA TEL07522096698 PRODUCTS SPECIFICATION WC0DR2611 Document revision history Revision Date Approved by Remarks Version 1.0 2016-05-25 Version 1.1 2016-05-26 Version 1.2 2016-05-31 Version 1.3 2016-06-07 Draft 1 Connector :change 6PIN to 5PIN 2 ADD Mechanical Dimensions:
Module A ,Module B 1 Modify Mechanical Dimensions 2 Modify ANT2 SPEC 3 Modify Connector SPEC 4 Modify ANT2 SPEC PAGE 2 OF 12 Version 1.3 PRODUCTS SPECIFICATION 1.2 General Requirements 1.2.1 IEEE 802.11b Section Feature 1.2.1.1 1.2.1.2 1.2.1.3 Standard Radio and Modulation Schemes Operating Frequency 1.2.1.4 Channel Numbers 1.2.1.5 1.2.1.6 Data Rate Media Access Protocol 1.2.1.7 Transmitter Output Power at Antenna Connector 1.2.1.8 Receiver Sensitivity at Antenna Connector 1.2.2 IEEE 802.11g Section Feature 1.2.2.1 1.2.2.2 1.2.2.3 Standard Radio and Modulation Type Operating Frequency 1.2.2.4 Channel Numbers 1.2.2.5 1.2.2.6 1.2.2.7 1.2.2.8 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector WC0DR2611 Detailed Description IEEE 802.11b DQPSK , DBPSK , DSSS , and CCK 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11,5.5,2,and 1Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain,Data Rate and at room Temp. 25
+19 dBm at 1Mbps
+18 dBm at 2Mbps
+17 dBm at 5.5Mbps
+16 dBm at 11Mbps Typical Sensitivity at Which Frame(1000-byte PDUs)Error Rate=8%
-88 dBm at 1Mbps
-82 dBm for 11Mbps Detailed Description IEEE 802.11g QPSK , BPSK , 16QAM ,64QAM with OFDM 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25
+18dBm at 6Mbps
+14dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25
-86 dBm at 6Mbps
-73 dBm at 54Mbps PAGE 3 OF 12 Version 1.3 PRODUCTS SPECIFICATION 1.2.3 IEEE 802.11a Section 1.2.3.1 Feature Standard Radio and Modulation Type 1.2.1.2 1.2.3.3 Operating Frequency 1.2.3.4 Channel Numbers 1.2.3.5 1.2.3.6 1.2.3.7 1.2.3.8 Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 1.2.4 IEEE 802.11n Section 1.2.4.1 Feature Standard 1.2.2.2 1.2.4.3 Radio and Modulation Type Operating Frequency 1.2.4.4 Data Rate WC0DR2611 Detailed Description IEEE 802.11a QPSK , BPSK , 16QAM ,64QAM with OFDM 5.15~5.25GHz and 5.725~5.825GHz for US and Canada 5.15~5.25GHz for Japan 5.15~5.25GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25
+18 dBm at 6Mbps
+14 dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25
-86 dBm at 6Mbps
-74 dBm at 54Mbps Detailed Description IEEE 802.11n BPSK , QPSK , 16QAM ,64QAM with OFDM 2.4GHz band:2400 ~ 2483.5MHz 5150~5250MHz, 5725~5850MHz MCS GI=800ns GI=400ns 20MHz 40MH 20MHz 40MHz 8 9 10 11 12 13 14 15 13 26 39 52 78 104 117 130 27 54 81 108 162 216 243 270 14.4 28.9 43.3 57.8 86.7 115.6 130 144.4 30 60 90 120 180 240 170 300 1.2.4.5 Media Access Protocol CSMA/CA with ACK 1.2.4.6 Transmitter Output Power at Antenna Connector Typical RF Output Power (tolerance2dB) at each RF chain,Data Rate and at roomTemp. 25 2.4GHz Band/HT20 18 dBm at MCS8 12 dBm at MCS15 PAGE 4 OF 12 2.4GHz Band/HT40 18 dBm at MCS8 12 dBm at MCS15 Version 1.3 PRODUCTS SPECIFICATION 5GHz Band/HT20 18 dBm at MCS8 12 dBm at MCS15 5GHz Band/HT40 WC0DR2611 18 dBm at MCS8 12 dBm at MCS15 Typical Sensitivity at each RF chain at Which Frame (1000-byte PDUs) Error Rate=10% and at room Temp. 25 2.4GHz Band/HT20
-86 dBm at MCS8 2.4GHz Band/HT40
-83 dBm at MCS8
-70 dBm at MCS15
-66 dBm at MCS15 1.2.4.7 Receiver Sensitivity at Antenna Connector 5GHz Band/HT20 5GHz Band/HT40
-86 dBm at MCS8
-83 dBm at MCS8
-71 dBm at MCS15
-67 dBm at MCS15 1.2.5 IEEE 802.11ac Section 1.2.5.1 Feature Standard Radio and Modulation Type 1.2.5.2 1.2.5.3 Operating Frequency 1.2.5.4 Channel Numbers 1.2.5.5 1.2.5.6 Data Rate Media Access Protocol 1.2.5.7 Transmitter Output Power at Antenna Connector 1.2.5.8 Receiver Sensitivity at Antenna Connector Detailed Description IEEE 802.11ac QPSK , BPSK , 16QAM ,64QAM,256QAM with OFDM 5.15~5.25GHz and 5.725~5.825GHz for US and Canada 5.15~5.25GHz for Japan 5.15~5.25GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China at most 866.7 Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at roomTemp. 25 HT80 18 dBm at MCS0 12 dBm at MCS8 11 dBm at MCS9 Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25 5GHz Band / HT80
-58 dBm at MCS9 PAGE 5 OF 12 Version 1.3 PRODUCTS SPECIFICATION 2. Electrical and Thermal Characteristics 2.1 Temperature Limit Ratings WC0DR2611 Minimum Maximum
-40 0 0
+80 60 125 Units Detailed Description Operating Voltage Current Consumption Form Factor and Interface High Speed USB2.0 Interface ANT1: Metal antenna ANT2: IPEX connector 5V10%
900mA Parameter Storage Temperature Ambient Operating Temperature Junction Temperature 2.2 General Section 2.2.1 Feature Antenna Type 2.2.2 2.2.3 2.2.4 2.3 Software Driver Windows XP/ WinCE/ Vista,/ Win7, Linux, MAC Security 64/128-bits WEP, WPA, WPA2 2.4 Mechanical Requirements 2.4.1 2.2.2 2.4.3 Feature Length Width High Detailed Description 45mm 25mm 7.0mm(PCB:1mm) PAGE 6 OF 12 Version 1.3 WC0DR2611 PRODUCTS SPECIFICATION 3. Connector Definition 5-Pin 1.25 mm connectorHorizontal Type Pin Symbol POWER_EN 1 2 GND 3 D+
4 D-
5 VCC5V 4 Mechanical Dimensions
*TOLERANCES ARE +/-0.5mm UNLESS OTHERWISE SPECIFIED
*UNIT:mm PAGE 7 OF 12 Version 1.3 ANT1ANT2 PRODUCTS SPECIFICATION Appendix 1 : SMT connector GH-5AWB-GF WC0DR2611 This is the N pin connector which is in common use.You can select 5pin according to your requirement. PAGE 8 OF 12 Version 1.3 PRODUCTS SPECIFICATION Appendix 2 : Antenna on board spec WC0DR2611 PAGE 9 OF 12 Version 1.3 PRODUCTS SPECIFICATION WC0DR2611 Appendix 3 : Antenna off board spec PAGE 10 OF 12 Version 1.3 PRODUCTS SPECIFICATION WC0DR2611 PAGE 11 OF 12 Version 1.3 IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent is otropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location:
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste,ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with Industry Canada RSS-102 for radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance cm between the radiator and your body. 20 20 The user manual for local area network devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:
(i) the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth shall be clearly indicated. Le guide d'utilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment
:
(I) l'appareil pour fonctionner dans la bande 5150-5250 MHz est rserv une utilisation intrieure pour rduire le potentiel d'interfrences nuisibles la co-
canal avec les systmes mobiles par satellite;
(Iii) pour les appareils avec antenne (s) dtachable, le gain d'antenne maximal autoris pour les appareils la bande 5725-5850 MHz doit tre telle que l'quipement satisfait encore la pire limites spcifies pour le point--point et non point--point de l'opration, le cas chant; et
(Iv) l'angle d'inclinaison du pire (s) ncessaire pour rester conforme la pire masque d'lvation condition nonce doit tre clairement indiqu. Host Product Labelling Requirements:
This transmitter module is authorization only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final en product must be labeled in a visible area with the following Contains IC: 12290A-WC0DR2611
"Contains FCC ID: 2AC23-WC0DR2611 d Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must not be collocated or operating in conjunction with any other antenna or transmitter.
This product uses the FCC Data API but is not endorsed or certified by the FCC