WC0HR2601 WIFI Module Users manual

 

PRODUCT SPECIFICATION Version 1.0 IEEE 802.11 a/b/g/n/ac 2T/2R Band USB2.0 Module Model Number: WC0HR2601

( REALTEK RTL8812BU ) 2.4G channel 1-13 5G channel 36-48 149-165 MAC address from GSD Custom Name Department Approval DESIGN 2016.09.26 Custom Approval Section Date CHECK APPROVAL 2016.09.26 2016.09.26 HUIZHOU GAOSHENGDA TECHNOLOGY CO., LTD 75 HUA YU RD., NO.75, ZHONGKAI HIGH-TECH DEVELOPMENT AREA, HUIZHOU, CHINA TEL07522096932 E-mail gaoz@gaosd.cn PRODUCTS SPECIFICATION WC0HR2601 Document revision history Revision Date Approved by Remarks Version 1.0 2016-09-26 Draft PAGE 2 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 1. General Description This document is to specify the product requirements for 802.11a/b/g/n/ac and Bluetooth USB Module. This Card is based on REALTEK RTL8812BU chipset .It is a complete dual-band(2.4GHz and 5GHz)WIFI 2 2 MIMO MAC/PHY/Radio System-on-a-Chip. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It is also backward complied with IEEE 802.11a standard from 5.15~5.825GHz wideband and IEEE 802.11b/g standard from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11 a/b/g/n/ac USB2.0 Module offers absolute interoperability with different vendors 802.11a/b/g/n/ac. Access Points through the wireless LAN. 2. Features Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate. Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate. Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate. Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate. Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps data rate. Operation at 2.4~2.5GHz and 5.15~5.825GHz frequency band to meet worldwide regulations Provides simple legacy and 20MHz/40MHz/80MHz co-existence mechanisms to ensure backward and network compatibility. Supports infrastructure networks via Access Point and ad-hoc network via peer-to-peer communication Supports IEEE 802.11i (WPA and WPA2),WAPI,. enhanced security Friendly user configuration and diagnostic utilities Drivers support Win10,Win8,Win7,XP,Linux High speed USB 2.0 interface ROHS compliant PAGE 3 OF 10 Version 1.0 PRODUCTS SPECIFICATION 3. Application Diagrams 3.1 Functional Block Diagram WC0HR2601 3.2 General Requirements 3.2.1 IEEE 802.11b Section 3.2.1.1 3.2.1.2 3.2.1.3 3.2.1.4 3.2.1.5 3.2.1.6 3.2.1.7 3.2.1.8 Feature Standard Radio and Modulation Schemes Operating Frequency Channel Numbers Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector Detailed Description IEEE 802.11b DQPSK , DBPSK , DSSS , and CCK 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11,5.5,2,and 1Mbps CSMA/CA with ACK Typical RF Output Power (tolerance2dB) at each RF chain, Data Rate and at room Temp. 25 degree C 19 dBm at 1Mbps 16 dBm at 11Mbps Typical Sensitivity at Which Frame(1000-byte PDUs)Error Rate=8%

-88 dBm at 1Mbps

-82 dBm at 11Mbps PAGE 4 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 3.2.2 IEEE 802.11g Section Feature Standard Radio and Modulation Type Operating Frequency Channel Numbers Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 3.2.2.1 3.2.2.2 3.2.2.3 3.2.2.4 3.2.2.5 3.2.2.6 3.2.2.7 3.2.2.8 3.2.3 IEEE 802.11a Section 3.2.3.1 3.2.3.2 Feature Standard Radio and Modulation Type 3.2.3.3 Operating Frequency Channel Numbers Data Rate Media Access Protocol Transmitter Output Power at Antenna Connector Receiver Sensitivity at Antenna Connector 3.2.3.4 3.2.3.5 3.2.3.6 3.2.3.7 3.2.3.8 Detailed Description IEEE 802.11g QPSK , BPSK , 16QAM ,64QAM with OFDM 2400 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at room Temp. 25degree C

+18 dBm at 6Mbps

+14 dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25 degree C

-86 dBm at 6Mbps

-73 dBm at 54Mbps Detailed Description IEEE 802.11a QPSK , BPSK , 16QAM ,64QAM with OFDM 5.15~5.35GHz and 5.725~5.825GHz for US and Canada 5.15~5.35GHz and 5.47~5.725GHz for Japan 5.15~5.35GHz and 5.47~5.725GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at room Temp. 25degree C

+18 dBm at 6Mbps

+14dBm at 54Mbps Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25 degree C

-86 dBm at 6Mbps

-73 dBm at 54Mbps PAGE 5 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 3.2.4 IEEE 802.11n Section Detailed Description 3.2.4.1 3.2.4.2 3.2.4.3 Feature Standard Radio and Modulation Type Operating Frequency IEEE 802.11n BPSK , QPSK , 16QAM ,64QAM with OFDM 2.4GHz band:2400 ~ 2483.5MHz 5GHz and:5150 ~ 5825MHZ MCS 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 GI=800ns 20MHz 6.5 13 19.5 26 39 52 58.5 65 13 26 39 52 78 104 117 130 40MH 13.5 27 40.5 54 81 108 121.5 135 27 54 81 108 162 216 243 270 GI=400ns 20MHz 7.2 14.4 21.7 28.9 43.3 57.8 65.0 72.2 14.444 28.889 43.333 57.778 86.667 115.556 130.000 144.444 40MHz 15 30 45 60 90 120 135 150 30 60 90 120 180 240 170 300 CSMA/CA with ACK Typical RF Output Power (tolerance2dB) at each RF chain, Data Rate and at room Temp. 25 degree C 2.4GHz Band/HT40 2.4GHz Band/HT20 18 dBm at MCS0 12 dBm at MCS7 5GHz Band/HT20 18 dBm at MCS0 12 dBm at MCS7 Typical Sensitivity at each RF chain at Which Frame(1000-byte PDUs)Error Rate=10% and at room Temp.25 degree C 18 dBm at MCS0 12 dBm at MCS7 5GHz Band/HT40 18 dBm at MCS0 12 dBm at MCS7 3.2.4.4 Data Rate 3.2.4.5 Media Access Protocol 3.2.4.6 Transmitter Output Power at Antenna Connector 3.2.4.7 Receiver Sensitivity at Antenna Connector 2.4GHz Band/HT20

-86 dBm at MCS0

-70 dBm at MCS7 2.4GHz Band/HT40

-83 dBm at MCS0

-66 dBm at MCS7 5GHz Band/HT20

-86 dBm at MCS0

-71 dBm at MCS7 5GHz Band/HT40

-83 dBm at MCS0

-67 dBm at MCS7 PAGE 6 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 3.2.5 IEEE 802.11ac Section 3.2.5.1 3.2.5.2 Feature Standard Radio and Modulation Type Detailed Description IEEE 802.11ac 3.2.5.3 Operating Frequency 3.2.5.4 3.2.5.5 3.2.5.6 Channel Numbers Data Rate Media Access Protocol QPSK , BPSK , 16QAM ,64QAM,256QAM with OFDM 5.15~5.35GHz and 5.725~5.825GHz for US and Canada 5.15~5.35GHz and 5.47~5.725GHz for Japan 5.15~5.35GHz and 5.47~5.725GHz for Europe 5.725~5.825GHz for China 12 non-overlapping channels for US and Canada 8 non-overlapping channels for Japan 19 non-overlapping channels for Europe 4 non-overlapping channels for China at most 866.7 Mbps CSMA/CA with ACK Typical RF Output Power(tolerance2dB) at each RF chain, Data Rate and at room Temp. 25degree C 3.2.5.7 Transmitter Output Power at Antenna Connector HT20 18 dBm at MCS0 12 dBm at MCS7 11 dBm at MCS8 HT80 HT40 18 dBm at MCS0 12 dBm at MCS8 11 dBm at MCS9 18 dBm at MCS0 12 dBm at MCS8 11 dBm at MCS9 Typical Sensitivity at each RF chain. Frame(1000-byte PDUs)Error Rate<10% at room Temp 25 degree C 3.2.5.8 Receiver Sensitivity at Antenna Connector 5GHz Band / HT20

-64dBm at MCS8 5GHz Band / HT80

-58dBm at MCS9 5GHz Band / HT40

-61dBm at MCS9 PAGE 7 OF 10 Version 1.0 5.2.1 5.2.2 5.2.3 5.2.4 4.3 Software Driver Security PRODUCTS SPECIFICATION 4. Electrical and Thermal Characteristics 4.1 Environmental Requirements WC0HR2601 Parameter Storage Temperature Ambient Operating Temperature Junction Temperature 4.2 General Section Minimum

-40 0 0 Maximum

+80 60 125 Units Feature Antenna Type Operating Voltage Current Consumption Form Factor and Interface High Speed USB2.0 Interface Detailed Description WIFI ANT :PIFA Antenna and IPEX 3.3 V10%

1000mA Win10,Win8,Win7, XP, Linux, MAC 64/128-bits WEP, WPA, WPA2 4.4 Mechanical Dimensions 4.4.1 4.4.2 4.4.3 Feature Length Width Height Detailed Description 47mm 30mm 7.0mm(PCB 1.0mm) PAGE 8 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 5 Connector Definition 10-Pin 1.25 mm connectorHorizontal Type Pin 3 1 3 Definition 3.3V 3.3V D-

4 D+

5 GND 6 WOWn 8 7 9 RST GND NC 10 GND 6 Mechanical Dimensions Note1: The below is left-off-board ANT diagram Note2:TOLERANCES ARE +/-0.5mm UNLESS OTHERWISE SPECIFIED

* UNITE :mm PAGE 9 OF 10 Version 1.0 PRODUCTS SPECIFICATION WC0HR2601 Appendix 1 : SMT connector GH-10AWB-GF This is the N pin connector which is in common use. You can select 10 pins according to your requirement. PAGE 10 OF 10 Version 1.0 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.