submitted | available | document details (if available) | source link |
---|---|---|---|
May 20 2018 | May 20 2018 |
various | User Manual | Users Manual | 325.52 KiB | May 20 2018 |
PRODUCTS USERMANUAL WC3XM2001 WIFI Module IEEE 802.11b/g/n/a/ac 2T/2R Model Number: WC3XM2001 Product Description The WC3XM2001 is a high-gain and low power consumption wifi module . It fully complies with rich wireless connectivity at high IEEE 802.11b/g/a/ac feature
/
Interface Standard WIFI Module Model Product Name 802.11b/g/n /a/ac WC3XM2001 Data Transfer Rate Product Features Product Specification Complies with IEEE 802.11g;
802.11b; 802.11n ; 802.11a ;802.11ac standard for 2.4GHz and5GHz Wireless LAN. TWO Transmit and TWO Receive path(2T2R) Supports Ad-Hoc/Infrastructure modes Works with all existing network nfrastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. Compatible with IEEE 802.11ac IEEE 802.11n and standards,delivers reliable,cost-effective,throughput from an extended distance.When 3.3V, USB bus and GND were connected,This module is working. date rate. Operating SystemsWindows XP 32/64,2000,Windows 7,Vista 32/64,Linux,Macintosh Low power consumption. Easy to install and configure. standard to provide wireless 866.7Mbps Operating Temperature Storage Temperature Modulation Method Operating Voltage Operation Range Frequency Band Operation Mode Transmit Power OS Support 3.3V10%
< 18dBm Humidity Security Ad hoc, Infrastructure 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,9 0,120 and maximum of 300Mbps QPSK , BPSK , CCK(802.11b) QPSK , BPSK , 16QAM ,64QAM with OFDM
(802.11g) BPSK , QPSK , 16QAM ,64QAM with OFDM(802.11n) QPSK , BPSK , 16QAM ,64QAM with OFDM
(802.11a) QPSK , BPSK , 16QAM ,64QAM,256QAM with OFDM(802.11ac) 2.4GHz: CH 1~CH13 for FCC 5GHz: 5150~5250MHz, 5725~5850MHz Up to 300 meters in open space Windows XP 32/64,2000,Windows 7,Vista 32/64,Linux,Macintosh WEP, TKIP, AES, WPA, WPA2
-10 ~ 70C ambient temperature
-55 ~ 125C ambient temperature 5 to 90 % maximum (non-condensing) PAGE 1 OF 3 Version 1.0 PRODUCTS USERMANUAL WC3XM2001 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. The devices must be installed and used in strict accordance with the manufacturers instructions as described in the user documentation that comes with the product. Modular could be only used in mobile or fix device, and could not be used in any portable device. The module must be installed in TV set. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Regulation information
(1) This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
(2) This compliance to FCC radiation exposure limits for an uncontrolled environment, and minimum of 20cm separation between antenna and body.
(3) The device is going to be operated in 5150~5250MHz frequency range. It is restricted indoor environment only.
(4) Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module.
(5) The end product must carry a label stating Contains FCC ID: 2AC23-WC3XM2001 or shall use e-labeling. PAGE 2 OF 3 Version 1.0 PRODUCTS USERMANUAL Canadian ISED Statement WC3XM2001 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. The device shall automatically discontinue transmission in cases of absence of information to transmit, or operational failure. Then it will scan the available radio signals. If this signal is connected before, it will be automatically connected, otherwise manual connections will be necessary. A host product shall use a physical label stating Contains IC: 12290A-WC3XM2001 or shall use e-labeling This radio transmitter (IC: 12290A-WC3XM2001) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device Antenna type Antenna gain 2412MHz to 2462MHz: Max gain: 2.18dBi 5150 MHz to 5250 MHz: Max gain: 3.63 dBi PIFA Antenna 5250 MHz to 5350 MHz: Max gain: 3.63 dBi 5470 MHz to 5725 MHz: Max gain: 3.63 dBi 5725 MHz to 5850 MHz: Max gain: 3.63 dBi ISED Radiation Exposure Statement This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 7.9 inches (20 cm) between the radiator
& your body. PAGE 3 OF 3 Version 1.0 PRODUCTS USERMANUAL Dclaration ISED canadienne WC3XM2001 Cet appareil est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interfrences, et (2) cet appareil doit accepter toute interfrence, y compris les interfrences pouvant provoquer un fonctionnement indsirable de l'appareil. Tout changement ou modification non expressment approuv par la partie responsable de la conformit peut annuler l'autorit de l'utilisateur utiliser l'quipement. Le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal. L'appareil doit automatiquement interrompre la transmission en cas d'absence d'informations transmettre, ou de panne oprationnelle. Ensuite, il va scanner les signaux radio disponibles. Si ce signal est connect auparavant, il sera automatiquement connect, sinon des connexions manuelles seront ncessaires. Un produit hte doit utiliser une tiquette physique indiquant "Contient IC: 12290A-WC3XM2001" ou doit utiliser un tiquetage lectronique. Cet metteur radio (IC: 12290A-WC3XM2001) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous avec le gain maximal admissible indiqu. Les types d'antennes non inclus dans cette liste, dont le gain est suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Type d'antenne le gain d'antenne 2412MHz 2462MHz: gain maximum: 2,18dBi 5150 MHz 5250 MHz: Gain maximum: 3,63 dBi pifa antenne 5250 MHz 5350 MHz: Gain maximum: 3,63 dBi 5470 MHz 5725 MHz: Gain maximum: 3,63 dBi 5725 MHz 5850 MHz: Gain maximum: 3,63 dBi Dclaration d'exposition aux rayonnements ISED:
Cet quipement est conforme aux limites d'exposition aux radiations RF IC dfinies pour un environnement non contrl. Cet metteur ne doit pas tre situ au mme endroit ou fonctionner conjointement avec une autre antenne ou metteur. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm (7,9 pouces) entre le radiateur et votre corps. PAGE 4 OF 3 Version 1.0
This product uses the FCC Data API but is not endorsed or certified by the FCC