TRDFRI ENGLISH FRANAIS ESPAOL 4 12 20 ENGLISH 4 WIRELESS ON/OFF SWITCH FUNCTIONS ON/OFF: Press to turn your control outlet on and off. Pairing: Add IKEA Smart Lighting products to your system. See instructions below. ADDING DEVICES TO YOUR WIRELESS ON/OFF SWITCH When the wireless ON/OFF switch is sold together with a control outlet (in the same package), they are already paired. To add more control outlets, just repeat the steps below:
Make sure that your control outlet is plugged in and the main power is turned on. 1 Hold the ON/OFF switch close to the control outlet you want to add (no more than 5 cm away). 2 Press and hold the pairing button for at least 10 seconds , you can find the pairing button under the rear cover. 5 3 A red light will shine steadily on the ON/
OFF switch. On your control outlet a white light will begin to dim and flash one time to indicate that it has been successfully paired. Up to 10 control outlets can be paired with 1 ON/OFF switch. Make sure to pair them one at a time. If the control outlets are close to each other, disconnect those that have already been paired from the wall outlet. FACTORY RESET YOUR DEVICE For wireless ON/OFF switch:
Press the pairing button 4 times within 5 seconds. CHANGING THE BATTERY When the wireless ON/OFF switch is used regularly and as intended, the battery will last for approximately 2 years. When its time to replace the battery, a red LED indicator will flash when you toggle the ON/OFF switch. Open the rear cover, and replace the battery with a new CR2032 battery. 6 CAUTION!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. IMPORTANT!
The wireless ON/OFF switch is for indoor use only and can be used in temperatures ranging from 0C to 40 C. Do not leave the wireless ON/OFF switch in direct sunlight or near any heat source, as it may overheat. The range between the wireless ON/OFF switch and the receiver are measured in open air. Different building materials and placement of the units can affect the wireless connectivity range. 7 CARE INSTRUCTIONS To clean the wireless ON/OFF switch wipe with a soft dry cloth. NOTE!
Never use abrasive cleaners or chemical solvents as this can damage the product. Save these instructions for future use. TECHNICAL DATA Type: E1743 wireless ON/OFF button Input: 3V, CR2032 Battery Range: 10 m in open air For indoor use only Operating frequency: 2405-2480Mhz Output power: 3 dBm Manufacturer: IKEA of Sweden AB Address: Box 702, SE-343 81 LMHULT 8 This device complies with Part 15 of the FCC Rules/Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation of the device. WARNING:
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance 9 with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 10 RF EXPOSURE INFORMATION This product is approved as a portable handheld device (not body worn) This product includes a static magnet, generating a magnetic field that might interfere with the normal operation of pacemakers, defibrillators, or other medical devices. Maintain a safe distance of separation between your medical device and this device. Stop using this device and consult your physician or medical device manufacturer if you believe that it is interfering with your medical device. License rights and limitations NO RIGHTS OR LICENSES, EXPRESS NO RIGHTS OR LICENSES, EXPRESS OR IMPLIED, ARE GRANTED TO USE THIRD-PARTY DEVICES IN COMBINATION WITH THESE PRODUCTS IN A WIRELESS MESH NETWORK, OR TO USE THIRD-
PARTY SERVICES TO ACCESS, MONITOR OR CONTROL THESE PRODUCTS IN A WIRELESS MESH NEWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK. 11 For use pursuant to U.S. Patent Nos.:
US 6,914,893 US 7,697,492 US 8,964,708 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store. FRANAIS 12 FONCTIONNALITS ON/OFF SANS FIL ON/OFF : appuyer pour allumer et teindre votre variateur dintensit. Appariement : ajoutez des produits de la gamme clairage connect IKEA votre systme. Voir instructions ci-
dessous. AJOUTER DES DISPOSITIFS LINTERRUPTEUR SANS FIL Si linterrupteur ON/OFF sans fil est vendu avec un variateur dintensit (dans la mme bote), les deux produits sont dj apparis. Pour ajouter des variateurs dintensit, rptez les tapes ci-dessous :
Assurez-vous que votre variateur dintensit soit branch et que le courant soit allum. 1 Placez linterrupteur ON/OFF prs du variateur dintensit que vous souhaitez ajouter (5 cm de distance maximum). 2 Maintenez le bouton dappariement enfonc pendant au moins 10 secondes. 13 Celui-ci se trouve sous le couvercle arrire. 3 Vous devriez voir une lumire rouge sallumer sur linterrupteur ON/OFF. Sur votre variateur dintensit, vous devriez voir une lumire blanche clignoter une fois pour indiquer que les deux dispositifs ont t apparis correctement. Vous pouvez apparier jusqu 10 variateurs dintensit chaque interrupteur ON/OFF. Veillez les apparier lun aprs lautre. Si les variateurs dintensit sont proches les uns des autres, dconnectez ceux qui ont dj t apparis de la prise murale. RINITIALISER LE DISPOSITIF Pour teindre/allumer distance :
appuyer sur le bouton dappariement 4 fois en 5 secondes. REMPLACEMENT DE LA PILE Si linterrupteur ON/OFF sans fil est utilis rgulirement et normalement, la pile durera environ 2 ans. Si la pile doit tre change, un voyant LED rouge clignotera lorsque linterrupteur sera activ/desactiv. 14 Ouvrir la faade pour accder la pile et la remplacer par une pile CR2032 neuve. ATTENTION !
Risque dexplosion si la pile est remplace par un type de pile incompatible. Les piles usages doivent tre mises au rebut selon les instructions. IMPORTANT !
Linterrupteur ON/OFF sans fil est conu pour un usage interne et rsiste aux temprature allant de 0C 40C. Ne pas placer linterrupteur ON/
OFF sans fil la lumire du soleil ou proximit dune source de chaleur. Risque de surchauffe. Lcart mesur entre linterrupteur ON/OFF sans fil et le rcepteur est mesur en champ libre. La porte de la connexion peut varier en fonction des matriaux de construction environnants et du placement des diffrents lments connects. 15 INSTRUCTIONS DE NETTOYAGE Nettoyer linterrupteur sans fil avec un chiffon doux et sec. ATTENTION !
Ne pas utiliser de produits nettoyants abrasifs ou de solvants chimiques au risque dendommager le produit. Conservez ces instructions pour une utilisation ultrieure. CARACTRISTIQUES TECHNIQUES Type : interrupteur sans fil E1743 Alimentation : 3V, pile CR2032 Porte : 10 m en champ libre. Usage en intrieur uniquement Frquence de fonctionnement :
2405-2480Mhz Puissance de sortie : 3 dBm Fabricant : IKEA of Sweden AB Adresse :
Box 702, 343 81 lmhult, SUDE 16 Cet appareil est conforme la section 15 des rgles de la FCC/aux normes RSS exemptes de licence dIndustry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas causer dinterfrence nuisible et
(2) cet appareil doit accepter toutes les interfrences reues, y compris celles qui peuvent causer un fonctionnement indsirable de lappareil. ATTENTION :
Tout changement ou modification apports cet appareil sans approbation expresse de la partie responsable de la conformit peut rendre nulle la capacit de lutilisateur utiliser cet appareil. REMARQUE :
Cet appareil a t test et il est conforme aux exigences relatives aux appareils lectroniques de classe B, selon la section 15 des rgles de la FCC (Commission fdrale des communications). Ces exigences sont prvues pour fournir une protection raisonnable contre les 17 interfrences nuisibles dans le cas dune installation domestique. Cet appareil gnre, utilise et peut mettre de lnergie sous forme de frquences radio. Si lappareil nest pas install ou utilis conformment aux instructions, il peut provoquer des interfrences perturbant les communications radio. Il est cependant impossible de garantir labsence totale dinterfrences dune installation donne. Si cet appareil produit des interfrences nuisibles la rception radio/tlvision, ce qui peut-tre dtermin en mettant successivement lappareil sous tension et hors tension, nous conseillons lutilisateur dessayer de remdier ce problme en suivant lune des procdures suivantes :
Rorienter ou dplacer lantenne de Augmenter la distance entre lappareil rception. et le rcepteur. Brancher lappareil une prise place sur un circuit diffrent de celui auquel le rcepteur est raccord. Contacter votre revendeur ou tout technicien radio/TV qualifi pour obtenir de laide. 18 RENSEIGNEMENTS SUR LEXPOSITION AUX RADIOFRQUENCES Ce produit a t approuv comme appareil tenir en main (et non pas porter sur soi). Cet appareil contient un aimant gnrant un champ magntique qui pourrait nuire au fonctionnement normal des stimulateurs cardiaques, des dfibrillateurs ou dautres appareils mdicaux. Maintenez une distance scuritaire entre lappareil mdical et ce produit. Si vous croyez que cet article IKEA modifie le fonctionnement de votre appareil, cessez de lutiliser et consultez votre mdecin ou le fabricant de votre appareil mdical. 19 Le pictogramme de la poubelle barre indique que le produit doit faire lobjet dun tri. Il doit tre recycl conformment la rglementation environnementale locale en matire de dchets. En triant les produits portant ce pictogramme, vous contribuez rduire le volume des dchets incinrs ou enfouis, et diminuer tout impact ngatif sur la sant humaine et lenvironnement. Pour plus dinformation, merci de contacter votre magasin IKEA. ESPAOL 20 FUNCIONES DEL INTERRUPTOR INALMBRICO ON/OFF: presiona para encender y apagar el interruptor de control. Acoplamiento: aade productos de Iluminacin Inteligente IKEA al sistema. A continuacin puedes ver las instrucciones. PARA AADIR DISPOSITIVOS Si el interruptor ON/OFF inalmbrico se vende con un dispositivo de control en la misma caja, estarn ya acoplados. Para aadir dispositivos de control, repite los pasos que aparecen a continuacin:
Asegrate de que el dispositivo de control est instalado y encendido. 1 Sita el interruptor ON/OFF cerca del dispositivo de control que quieras asociar, (5 cm de distancia como mximo). 2 Mantn presionado el botn de acoplamiento al menos. Una luz LED roja debera encenderse en el interruptor ON/OFF. durante 10 segundos 21 En el dispositivo de control deberas ver luz blanca papadear una vez para indicar que los dos dispositivos se han acoplado correctamente. 3 La fuente luminosa parpadear una vez para indicar que los dos elementos se han asociado correctamente. Puedes asociar hasta 10 dispositivos de control a cada interruptor ON/OFF. Asocia los dispositivos uno detrs de otro. Si los dispositivos estn cerca unos de otros, desconecta del interruptor principal los que ya estn acoplados. REINICIAR EL DISPOSITIVO Para el interruptor ON/OFF:
Presiona el botn de acoplamiento 4 veces durante 5 segundos. PARA CAMBIAR LA PILA Si el interruptor inalmbrico ON/OFF se utiliza con regularidad y de forma normal, la pila durar unos 2 aos. Cuando la plia se deba cambiar, parpadear un piloto rojo LED cuando el interruptor se active/desactive. 22 Abre la tapa posterior y reemplaza la pila por una CR2032 nueva. ATENCIN!
Riesgo de explosin si se reemplaza la pila por un tipo incompatible. Las pilas usadas se deben eliminar segn las instrucciones. IMPORTANTE!
El interruptor ON/OFF ha sido diseado para uso en el interior y resiste temperaturas entre 0C y 40C. No sites el interruptor directamente bajo la luz del sol ni cerca de fuentes de calor, porque podra recalentarse. El espectro entre el interruptor ON/
OFF y el receptor se mide al aire libre. El alcance de la conexin puede variar segn los materiales de construccin del entorno y de la ubicacin de los distintos elementos conectados. 23 LIMPIEZA Limpiar el interruptor ON/OFF con un pao seco. ATENCIN!
No utilices productos de limpieza abrasivos o disolventes qumicos, porque podras daar el producto. Guarda estas instrucciones para consultarlas ms adelante. DATOS TCNICOS Tipo: interruptor ON/OFF inalmbrico E1743. Entrada: 3V, pila CR2032. Alcance: 10 m al aire libre. Para uso solo en el interior. Frecuencia de funcionamiento:
2.405-2.480MHz. Potencia de salida: 3 dBm. Fabricante: IKEA of Sweden AB. Direccin:
Box 702, SE-343 81 LMHULT. 24 Este aparato cumple la parte 15 de las reglas de la FCC/de las normas RSS exentas de licencia de Industry Canad. Su funcionamiento est sometido a las dos condiciones siguientes:
(1) este aparato no debe causar interferencias dainas y
(2) este aparato debe aceptar todas las interferencias recibidas, incluidas las que pueden causar el funcionamiento indeseado del aparato. ATENCIN:
Cualquier cambio o modificacin que se realice en este aparato sin la aprobacin expresa de la parte responsable de la conformidad puede anular la capacidad del usuario para utilizar el aparato. NOTA:
Este equipo ha sido probado para comprobar que cumple los lmites establecidos en los dispositivos digitales de Clase B, segn el apartado 15 del reglamento FCC. Estos lmites se han establecido para proporcionar una proteccin razonable contra las 25 interferencias perjudiciales en una instalacin domstica. Este equipo genera, usa e irradia energa de radiofrecuencia, y si no se instala y se usa de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones por radio. Sin embargo no existe garanta de que no se produzcan interferencias en una instalacin en concreto. Si el equipo produjera interferencias perjudiciales en la recepcin de radio o TV, lo que se puede comprobar encendiendo y apagando el equipo, recomendamos al usuario que intente corregir dichas interferencias adoptando una o ms de las siguientes medidas:
Reorientar o recolocar la antena receptora. el receptor. Aumentar la distancia entre el equipo y Conectar el equipo a un enchufe o circuito distinto al que est conectado el receptor. Solicitar ayuda al vendedor o a un tcnico cualificado de radio/TV. 26 INFORMACIN SOBRE LA EXPOSICIN A RF Este producto ha sido aprobado para utilizarse como un aparato porttil (no se debe llevar pegado al cuerpo) Este producto incluye un imn esttico, lo que genera un campo magntico que puede interferir con la operacin normal de marcapasos, desfibriladores y otros aparatos mdicos. Mantn una distancia segura entre tu aparato mdico y este aparato. Deja de usar este aparato y ponte en contacto con tu mdico o con el fabricante del aparato mdico si piensas que est interfiriendo con tu aparato mdico. 27 La imagen del cubo de basura tachado indica que el producto no debe formar parte de los residuos habituales del hogar. Se debe reciclar segn la normativa local medioambiental de eliminacin de residuos. Cuando separas los productos que llevan esta imagen, contribuyes a reducir el volumen de residuos que se incineran o se envan a vertederos y minimizas el impacto negativo sobre la salud y el medio ambiente. Para ms informacin, ponte en contacto con tu tienda IKEA. Inter IKEA Systems B.V. 2018 AA-2104032-1