GSM0508IG001 Expedite L10-G Integration Guide Version: 1.00 Wednesday, May 07, 2014 General TERMS OF USE OF NEW MATERIALS - PLEASE READ CAREFULLY From time to time, Novatel Wireless, in its sole discretion, may make available for download on its website (www.novatelwireless.com), or may transmit via mail or email, updates or upgrades to, or new releases of, the firmware, software or documentation for its products
(collectively,
'New Materials'). Use of such New Materials is subject to the terms and conditions set forth below, and may be subject to additional terms and conditions as set forth in Novatel Wireless's Technical Support Policy (posted on its website) and/or any written agreement between the user and Novatel Wireless. All New Materials are provided AS IS. Novatel Wireless makes no warranty or representation with respect to the merchantability, suitability, functionality, accuracy or completeness of any such New Materials. The user of such New Materials assumes all risk (known or unknown) of such use. Novatel Wireless reserves all rights in such New Materials. The user shall have only a revocable and limited license to use such New Materials in connection with the products for which they are intended. Distribution or modification of any New Materials without Novatel Wireless's consent is strictly prohibited. IN NO EVENT WILL NOVATELWIRELESS BE RESPONSIBLE FOR ANY INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES AS A RESULT OF THE USE OF ANY NEW MATERIALS. NOVATELWIRELESS 'S MAXIMUM LIABILITY FOR ANY CLAIM BASED ON THE NEW MATERIALS SHALL NOT EXCEED FIFTY U.S. DOLLARS ($50). Version Verification Please ensure you have the latest version of this document by downloading it from www.novatelwireless.com i novatelwireless.com Copyright 2014 Novatel Wireless. All rights reserved. Complying with all applicable copyright laws is the responsibility of the user. Without limiting the rights under copyright, no part of this document may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), or for any purpose, without the express written permission of Novatel Wireless. Novatel Wireless and the Novatel Wireless logo are either registered trademarks or trademarks of Novatel Wireless, Inc. in the United States. 251 Renner Pkwy, Suite 200 Richardson, TX 75080 USA Phone: (972) 633-4400 Fax: (972) 633-4444 Email: info@nvtl.com www.novatelwireless.com ii novatelwireless.com Warranty Information This warranty applies to (a) products sold directly by Novatel Wireless, unless a different warranty is specified in a written agreement between Novatel Wireless and the purchaser;
and (b) products sold to end users through a distributor authorized by Novatel Wireless, but only where the authorized distributor does not provide a separate warranty on such products, and Novatel Wireless has agreed to provide this warranty to such end users. If you purchased the product from an authorized distributor, please check whether this warranty from Novatel Wireless or a separate warranty from the distributor applies to your purchase. This warranty does not apply to any (i) accessories or batteries for the products; or (ii) demonstration samples or prototypes of the products. Unless otherwise provided in a written agreement between Novatel Wireless and the purchaser, all such accessories, batteries, samples or prototypes are provided by Novatel Wireless AS IS without any warranty of any kind. Novatel Wireless warrants to the original purchaser of the product from Novatel Wireless or its authorized distributor (as applicable) that, for a period of one (1) year from the date of shipment of the product from Novatel Wireless, the product hardware will be substantially free from defects in material or workmanship under normal operation, and the product firmware will perform substantially in accordance with the product documentation provided by Novatel Wireless. Novatel Wireless does not warrant that (a) the product hardware or firmware will meet the purchaser's requirements; (b) the operation of the product hardware or firmware will be uninterrupted or error-free; or (c) the product, when integrated in, or combined with, other products or software not supplied by Novatel Wireless, will continue to perform substantially in accordance with the product documentation. This limited warranty is for the benefit of the original purchaser, and is not transferable. During the warranty period, Novatel Wireless, at its expense and in its sole discretion, will repair the product, or replace the product with a corresponding or equivalent product, if it is determined to have a covered defect, provided that the purchaser first notifies Novatel Wireless (directly or through its authorized distributor from which the product was purchased) of any such defect, furnishes Novatel Wireless with a proof of purchase (if required), requests and obtains a return merchandize authorization (RMA) number from Novatel Wireless, and returns the product under that RMA to Novatel Wireless (or, at Novatel Wireless option, to its authorized distributor), with the shipping charges being prepaid by purchaser. If, upon reasonable examination of the returned product, Novatel Wireless does not substantiate the defect claimed by purchaser, or determines that the defect is not covered under this limited warranty, Novatel Wireless will not be required to repair or replace the product, but may instead reship the product to the purchaser (or, at Novatel Wireless'
option, to its authorized distributor where the product can be made available to purchaser), in which case the purchaser shall be responsible for paying Novatel Wireless' cost for reshipping the product to purchaser (or to Novatel Wireless' authorized distributor), and Novatel Wireless' usual charges for unpacking, testing, and repacking the product for reshipment to iii novatelwireless.com purchaser (or to Novatel Wireless' authorized distributor).Purchaser shall bear the risk of loss or damage in transit to any product returned by purchaser to Novatel Wireless, or any returned product not found to be defective or covered under this warranty, and reshipped by Novatel Wireless to purchaser (or to Novatel Wireless' authorized distributor). In the event Novatel Wireless repairs or replaces a defective product covered by this limited warranty, the repaired or replacement product will be covered under this limited warranty for the remainder of the original warranty period on the defective product, or a period of ninety (90) days, whichever is longer. If Novatel Wireless is unable to repair or replace a defective product covered by this limited warranty, Novatel Wireless will provide to purchaser a credit or a refund (at Novatel Wireless' option) of the original purchase price (excluding taxes and shipping charges). Any returned and replaced product, or any product for which Novatel Wireless has furnished a credit or a refund, becomes the property of Novatel Wireless. Novatel Wireless shall not have any obligation to provide any firmware bug fixes, upgrades or new releases except as may be necessary to correct any covered defect of which purchaser notifies Novatel Wireless in writing during the warranty period. Novatel Wireless, from time to time and in its sole discretion, may make available for download on its website
(www.novatelwireless.com), or may provide via email, certain firmware bug fixes, upgrades or new releases for the product. Download and use of any such bug fixes, upgrades or new releases is subject to all of the applicable terms and conditions of Novatel Wireless' technical support policy as posted and updated on its website. Novatel Wireless shall have no obligation under this limited warranty for (a) normal wear and tear; (b) the cost of procurement of substitute products; or (c) any defect that is (i) discovered by purchaser during the warranty period but for which purchaser does not request an RMA number from Novatel Wireless, as required above, until after the end of the warranty period, (ii) caused by any accident, misuse, abuse, improper installation, handling or testing, or unauthorized repair or modification of the product, (iii) caused by use of any materials not supplied by Novatel Wireless, or by use of the product other than in accordance with its documentation, or (iv) the result of electrostatic discharge, electrical surge, fire, flood or similar causes. The purchaser (or its customers, as applicable) shall be solely responsible for the proper configuration, testing and verification of the Novatel Wireless product prior to deployment in the field, and for ensuring that any end user product or system into which the Novatel Wireless product is integrated or incorporated operates as intended and meets the requirements of purchaser (or its customers). Novatel Wireless shall have no responsibility whatsoever for the integration, configuration, testing, verification, installation, upgrade, support or maintenance of any such end user product or system, or for any liabilities, damages, costs or expenses associated therewith. iv novatelwireless.com NOVATEL WIRELESS' SOLE RESPONSIBILITY AND PURCHASER'S SOLE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE FOR NOVATEL WIRELESS TO REPAIR OR REPLACE THE PRODUCT (OR IF REPAIR OR REPLACEMENT IS NOT POSSIBLE, PROVIDE A CREDIT OR REFUND OF THE PURCHASE PRICE) AS PROVIDED ABOVE. NOVATEL WIRELESS EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, SATISFACTORY PERFORMANCE AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL NOVATEL WIRELESS BE LIABLE FOR ANY INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING WITHOUT LIMITATION LOSS OR INTERRUPTION OF USE, DATA, REVENUES OR PROFITS) RESULTING FROM A BREACH OF THIS WARRANTY OR BASED ON ANY OTHER LEGAL THEORY, EVEN IF NOVATEL WIRELESS HAS BEEN ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES. Some jurisdictions may require a longer warranty period than specified above and, accordingly, for products sold in those jurisdictions the applicable warranty period shall be extended as required under the laws of those jurisdictions. Furthermore, some jurisdictions may not allow the disclaimer of implied warranties or the exclusion or limitation of incidental or consequential damages, so the above disclaimer, limitation or exclusion may not apply to products sold in those jurisdictions. This limited warranty gives the purchaser specific legal rights and the purchaser may have other legal rights that vary from jurisdiction to jurisdiction. This limited warranty shall be governed by the laws of the State of Texas, United States of America, without regard to conflict of laws principles. This limited warranty shall not be governed in any respect by the United Nations Convention on Contracts for the International Sale of Goods. v novatelwireless.com Regulatory Compliance FCC CERTIFICATION Novatel Wireless certifies that the Expedite L10-G GSM Radio Module complies with the RF requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E and Part 22 Subpart H of the FCC Rules and Regulations. This certification is contingent upon installation, operation and use of the Expedite L10-G module and its host product in accordance with all instructions provided to both the OEM and end user. When installed and operated in a manner consistent with the instructions provided, the Expedite L10-G module meets the maximum permissible exposure (MPE) limits for general population / uncontrolled exposure as defined in Section 1.1310 of the FCC Rules and Regulations. The Expedite L10-G module is designed for use in a variety of host units, enabling the host platform to perform wireless data communications. However, there are certain criteria relative to integrating the modem into a host platform such as a PC, laptop, handheld, monitor and control unit, etc. that must be considered to ensure continued compliance with FCC compliance requirements. Important Information for Canada/USA OEM Integrators This section provides guidance for using the Expedite L10-G in host devices through the FCC Permissive Change process. When utilizing the permissive change process, Novatel Wireless, the grantee, is responsible for all integrations and must be consulted on all regulatory matters involving the Expedite L10-G. for mobile 1 The Expedite L10- G module is granted with FCC/IC modular approval applications, and may be installed as a standalone2 transmitter in final products meeting the following conditions. If the following conditions are followed, it may be used in final products without additional FCC/IC certification. Otherwise, additional FCC/IC approvals must be obtained. 1Mobile Device Definition FCC defines as a transmitting antenna located at a distance 20cm from the user. 2Standalone is defined as a single transmitter transmitting as opposed to 2 or more transmitters transmitting simultaneously. vi novatelwireless.com The antenna connected to the Expedite L10-G module must be installed to provide at least 20 cm separation from the human body at all times. The Expedite L10-G module and transmitter antennas must not be co-located with any other transmitter or antenna within a host device. The transmitter antenna used with the Expedite L10-G module must not exceed the following level:
Cellular maximum permitted antenna gain: 5.39dBi PCS band maximum permitted antenna gain: 3.31dBi To comply with the aspects of KDB996369, strict adherence to the design parameters in Section 4.1.1.3 Antenna And RF Signal Trace must be observed. Section 4.1.1.3 provides PCB RF trace design guidelines for the coplanar microstrip between the Expedite L10-G RF compression pads and the U.FL style coaxial connector. A label containing the FCC and Industry Canada IDs must be permanently affixed to the exterior of the host device into which the Expedite L10-G module is installed. The label may also be under a panel or battery pack if it is readily accessible and cannot be separated from the host device itself. The label must contain a statement similar to the following;
This device contains FCC ID: PKRNVWGSM0508 This equipment contains equipment certified under IC: 3229A-GSM0508 If any of these conditions are not met then additional information should be sought from the FCC or an FCC qualified test laboratory. If the Expedite L10-G module is intended for use in a portable1 device, the OEM integrator is responsible to design the product to comply with RF exposure, and must work with Novatel Wireless (the grantee) to satisfy FCC/IC SAR requirements. Refer to FCC OET Bulletin 65 Supplement C for information about FCC RF exposure compliance requirements for mobile and portable devices. The system user manuals and other documentation must clearly indicate operating conditions that must be observed to ensure compliance with FCC/IC RF exposure guidelines and also include appropriate caution and warning statements and information. The host device containing the Expedite L10-G module may also require compliance to FCC Part 15 Subpart B Unintentional Radiators. 1Portable Device Definition FCC defines as a transmitting antenna located at a distance 20cm from the user. vii novatelwireless.com FCC NOTICE TO USERS Novatel Wireless has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the device. See 47 CFR Sec. 15.21. The device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna. l Increase the separation between the equipment and receiver. l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. l Consult the dealer or an experienced radio/TV technician for help. If the FCCID of the module is not visible when installed in the host platform, then a permanently attached or marked label must be displayed on the host unit referring to the module. The label should contain wording such as:
Contains FCC ID: PKRNVWGSM0508 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Industry Canada IC: 3229A-GSM0508 MODEL NUMBER: GSM0508 This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. viii novatelwireless.com In order to use the Expedite L10-G module without any additional FCC certification the installation must meet the following conditions:
The system antenna(s) connected to the Expedite L10-G module must be installed to provide at least 20 cm separation from the human body during normal operation. The system antennas must not be co-located with any other transmitter or antenna. The system antenna(s) used with the Expedite L10-G module must not exceed the following level:
Cellular maximum permitted antenna gain: 5.39dBi PCS band maximum permitted antenna gain: 3.31dBi Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Afin d'utiliser le Expedite L10-G module sans aucune certification de d'Industrie Canada supplmentaire l'installation doit satisfaire aux conditions suivantes:
L'utilisation du systme connecte au module de Expedite L10-G doit tre installe pour fournir la sparation d'au moins 20 cm du corps humain pendant une opration normale. Les antennes du systme ne doivent pas tre colocaliss avec un autre metteur ou antenne. L'utilisation du systme utilise avec le module de Expedite L10-G ne doit pas dpasser les niveaux suivants:
Cellulaires le permis gain maximal est de 5.39dBi PCS groupent le gain maximal est de 3.31dBi ROHS COMPLIANCE As a part of Novatel Wireless corporate policy of environmental protection, Novatel Wireless takes every step to ensure that the Expedite L10-G modules are designed and manufactured to comply to the European Union Directive 2002/95/EC for the Restriction of Hazardous Substances (RoHS). CE (European Union Notice) If this product has telecommunications functionality, requirements of the following EU Directive:
it also complies with the essential
* R&TTE Directive 1999/5/EC ix novatelwireless.com Compliance with these directives implies conformity to harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by Novatel Wireless Inc. for this product or product family. This compliance is indicated by one of the following conformity markings placed on the product. This CE marking is valid for EU non-harmonized telecommunications products CE 0560 NCC NOTICE NCC ID: CCAF133G0170T1 x novatelwireless.com Important Safety Information The following information applies to the devices described in this manual. Always observe all standard and accepted safety precautions and guidelines when handling any electrical device. l Save this manual: it contains important safety information and operating instructions. l Do not expose the Expedite L10-G product to open flames. l Ensure that liquids do not spill onto the devices. l Do not attempt to disassemble the product: Doing so will void the warranty. This product does not contain consumer-serviceable components. The Enabler Expedite L10-G module may not be used in an environment where radio frequency equipment is prohibited or restricted in its use. This includes aircraft, airports, hospitals, and other sensitive electronic areas. Do not operate RF devices in an environment that may be susceptible to radio interference resulting in danger, specifically;
l Areas where prohibited by the law. l Follow any special rules and regulations and obey all signs and notices. Always turn off the host device when instructed to do so, or when you suspect that it may cause interference or danger. l Where explosive atmospheres may be present. l Do not operate your modem in any area where a potentially explosive atmosphere may exist. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Be aware of and comply with all signs and instructions. l Users are advised not to operate the modem while they are at a refueling point or service station. l Users are reminded to observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas), chemical plants or where blasting operations are in progress. l Areas with a potentially explosive atmosphere are often but not always clearly marked. l Potential locations can include gas stations, below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle engine. l Near Medical and life support equipment. l Do not operate your modem in any area where medical equipment, or life support equipment may be located, or near any equipment that may be susceptible to any form of radio interference. In such areas, the host communications device must be turned off. The modem may transmit signals that could interfere with this equipment. l On an aircraft, either on the ground or airborne. l In addition to FAA requirements, many airline regulations state that you must suspend wireless operations before boarding an airplane. Please ensure that the host device is turned off prior to boarding an aircraft in order to comply with these regulations. The modem can transmit signals that could interfere with various onboard systems and controls. xi novatelwireless.com l While operating a vehicle l The driver or operator of any vehicle should not operate a wireless data device. Doing so will detract from the driver or operator's control and operation of that vehicle. In some countries, operating such communication devices while in control of a vehicle is an offense. Disclaimer The information and instructions contained within this publication comply with all FCC, GCF, PTCRB, R&TTE, IMEI and other applicable codes that are in effect at the time of publication. Novatel Wireless disclaims all responsibility for any act or omissions, or for breach of law, code or regulation, including local or state codes, performed by a third party. Novatel Wireless strongly recommends that all installations, hookups, transmissions, etc., be performed by persons who are experienced in the fields of radio frequency technologies. Novatel Wireless acknowledges that the installation, setup and transmission guidelines contained within this publication are guidelines, and that each installation may have variables outside of the guidelines contained herein. Said variables must be taken into consideration when installing or using the product, and Novatel Wireless shall not be responsible for installations or transmissions that fall outside of the parameters set forth in this publication. Novatel Wireless shall not be liable for consequential or incidental damages, injury to any person or property, anticipated or lost profits, loss of time, or other losses incurred by Customer or any third party in connection with the installation of the Products or Customer's failure to comply with the information and instructions contained herein. xii novatelwireless.com Table of Contents 1 Introduction Technical Specifications General Radio Technology Speech Features Supplementary Services USB/UART Features SMS Features SIM-Based Features Customized Features Multiple Configurations Customer Tool Design Package Power Environmental Packet Data Transfer Regulatory Reference Documents Typical Usage Contacting Novatel Wireless 2 Module Power Operating Power Typical Input Current 3 Interfaces I/O Connector Pin Assignments 1 3 3 3 3 3 3 3 3 4 4 4 5 5 5 5 5 6 7 7 8 9 9 10 11 xiii novatelwireless.com Analog Audio Interface Speaker Microphone Microphone Type Support Headset Specific Absorption Rate (SAR) Guidelines SAR Compliance 3 Tune Up Procedures Tune Up Procedure 14 14 15 15 15 16 18 18 19 20 xiv novatelwireless.com 1 Introduction Technical Specifications Typical Usage Contacting Novatel Wireless 1 novatelwireless.com The Expedite L10-G 2G data modem is a small wireless data modem providing 2G wireless data connectivity for portable and hand held computers, point-of-sale devices, and other machine-to-machine applications. It is a compact, wireless OEM module that uses the Global System for Mobile Communications
(GSM) international communications standard to provide two-way wireless capabilities. The Expedite L10-G module is a fully approved GSM device, enabling application-specific, two-
way communication and control. The small size of the Expedite L10-G module allows it to integrate easily into the application and packaging. Figure 1-1 Expedite L10-G Module 2 novatelwireless.com Technical Specifications General Name:
Model:
Radio Technology Quad-band EDGE/GSM/GPRS:
Class:
Modulation Coding Schemes:
Mode of Operation:
Speech Features Expedite L10-G GSM0508-40 850/900/1800/1900 MHz Supports class 8, 10 and 12 (The default GPRS class is 8) CS-1 to CS-4 Class B (attaches to both GSM and GPRS at the same time) Speech Codec:
Speech Interface:
AMR HR FR EFR Analog/PCM Supplementary Services Speech Codec:
Number identification Call Offering Call Completion Multi-Party USSD USB/UART Features USB 1.1:
USB VID/PID:
UART1 (2-wire):
UART2 (4 wire):
For download image only. MTKs VID/PID as 0E8D/0003, Only for download mode. For download image and debug port CMUX Support SMS Features SMS over GPRS:
Concatenated SMS:
SMS Cell Broadcast:
SMS Immediate Notification:
SIM-Based Features Mobile Originated and Mobile Terminated Yes, up to 10 messages Supported by AT commands Supported by AT commands SIM Personalization Locks:
SIM Application Toolkit:
SIM Lock/Network lock , Supports restricting SIM/USIM card Supported by AT commands 3 novatelwireless.com Customized Features Notification for incoming call and SMS: Provide one GPIO pin for notification Host wake-up modem event:
Modem AT command ready event:
CMUX:
Boot up ready message:
Monitor modem power on/off status:
Provide one interrupt pin to wake-up modem Provide one GPIO pin to notify host that AT command is ready Supports CMUX feature Shows AT Command Interpreter Ready as boot up ready Provide a resistor VEXT28 to monitor the power on/off status of modem For verifying the RF power in customer product. AT command to adjust the band, chan-
nel and output max power:
Multiple Configurations AT command to switch speech inter-
face (Analog/PCM):
AT command to change UART2s baud rate:
AT command to change GPRS class:
AT command to change UART2 flow control:
AT command to read the operator data (MCC/MNC):
AT command to read the network lock password:
1. Supports to switch speech interface between PCM and analog. 1. Supports baud rate up to 921,600 bps 2. The default baud rate of UART2 is 115,200 bps 1. Supports class 8, 10 and 12 2. The default GPRS class is 8 1. Supports to change the UART2s flow control as None, HW flow control and SW flow control 2. The default flow control is none flow control 1. Read Network Lock Data 1. Read Network Lock Password Customer Tool Debug tool:
Catcher tool user guide:
Flash tool:
Flash tool user guide:
Tx Power Adjust tool:
IMEI re-write tool:
Catcher tool execution package Supports Windows XP, Windows Vista and Windows 7 Catcher_Tool_user_guide-v0.1-2013.05.31.pdf Flash tool execution package Supports Windows XP, Windows Vista and Windows 7 Flash_Tool_user_guide-v0.1-2013.05.31.pdf USI_TX_Power_Adjust_Tool-V0.1-20130829.pdf IMEI_API_Introduction-V0.1-20130923.pdf 4 novatelwireless.com Design Package Upgrade agent introduction:
Compare between BROM Lite and Flash Tool:
CMUX sample code (Linux):
CMUX introduction:
UART flow control introduction:
AT Command set:
Audio parameter adjustment:
The user guide of AT command to adjust the band, channel and output max power:
Power Electrical Power:
Peak currents and average power dissipation:
Environmental 1. BROM_Lite_Introduction-v0.2-20130709.pdf 2. System Information to build the BROM lite tool-v0.1-2013.07.09.pdf BROM_Lite_vs_Flash_Tool-V0.1-2013.06.10.pdf smmux-alpha-2.tar.gz 1. CMUX_introduction-v0.1-2013.05.31.pdf 2. pppd.7z UART_Flow_Control-v0.1-2013.05.31.pdf Expedite L10-G_AT_Command_Set_v0.8.6_20131008.doc Expedite L10-G_Audio_Parameter_Adjustment-V0.3-2013.08.22.pdf AT_ERFTX-V0.1-20130924.pdf 3.3 to 4.35 Vdc (vbat) Supply Vripple must be less than 200 mV across all frequencies Refer to the Operating Power table in the Technical Specifications for peak currents and average power dissipation for various modes of oper-
ation. Compliant Operating Temperature:
Operating Temperature:
Storage Temperature:
Humidity:
Emissions:
-20 C to 60 C
-30 C to 70 C
-40 C to 85 C Up to 95% non condensing FCC 47 CFR Parts 2,15,22 & 24 Packet Data Transfer Protocol:
Short Message Services:
Regulatory Agency approvals:
Text, MO/MT FCC Certification Industry Canada PTCRB CE GCF 5 novatelwireless.com Reference Documents CNN0401xAT001 - HS 3002 AT Command Reference CNN0401xTG001 - HS 3002 Transition Guide ENF0000SD001 - HDK Guide CNN0401AN001 - Using Digital Audio on the HS 3002 6 novatelwireless.com Typical Usage The following applications can use the Expedite L10-G module for transmitting/receiving data/voice:
l Automated Meter Reading (AMR) l Point of Sale Applications (POS) l E-mail and Internet access l Automated Vehicle Location (AVL) l Machine to Machine communication (M2M) l Telematics l Telemetry l Wireless Security l Smart Phones l Telemedicine Contacting Novatel Wireless For technical support and customer service dealing with the modem itself, contact the company where you purchased the product. If you purchased the product directly from Novatel Wireless, visit the Support page on the Novatel Wireless web site:
www.novatelwireless.com 7 novatelwireless.com 2 Module Power Operating Power 8 novatelwireless.com Operating Power The Expedite L10-G module requires an in/out voltage of 3.3V to 4.35V. The supply ripple must be less than 200 mV across all frequencies. Typical Input Current Typical Results @ 3.8 V 25 deg C, with 1 F at connector input on VBAT and RF terminated into a 50 resistive load. Traffic Data Rate: Full Band Mode GSM850 PCL=5, TX=32.5dBm PCL=19, TX=5dBm EGSM PCL=5, TX=32.5dBm PCL=19, TX=5dBm PCL=0, TX=29.5dBm PCL=15, TX=0dBm PCL=0, TX=29.5dBm PCL=15, TX=0dBm Sleep with Paging Multi-frames=5 Sleep Shutdown DCS PCS Both Both Both Avg
(mA) Peak
(mA) Notes 211 59.8 231 59.6 142 57.3 149 57.9
<1
< 0.9 0.25 1810
-
2040
-
1140
-
1190
-
90
-
0.3 GPRS, 1TX GPRS, 1TX GPRS, 1TX GPRS, 1TX Modem registered; peak during network activity For minimum current draw in shut down mode, we recommend you shut down the modem by either sending AT$OFF (AT$OFFDLY must be >0) or by send-
ing a pulse on PON line (pin 35), and then setting the ON/OFF line (pin 37) low to remove power from the device. 9 novatelwireless.com 3 Interfaces I/O Connector Pin Assignments Analog audio interface Specific Absorption Rate (SAR) Guidelines 10 novatelwireless.com Figure 3-1 Pin 1 Reference, 68-Pin I/O Connector I/O Connector Pin Assignments The following table shows the pin assignments for the input/output connector. Pin 01 02 03 04 05 06 07 Function Description Notes GND DAIPCMIN Reserve Pin DAISYNC Reserve Pin Reserve Pin VSIM1 Ground PCM data in Reserved for debug PCM sync Reserved for debug Reserved for debug LDO - VSIM output.Provide 1.8/3.0V to SIM card. 2.8V 2.8V 1.8/3.0V 11 novatelwireless.com Pin 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Function Description Notes PWR_KEY GPIO/INT1 ACCDET AP_READY_INT U2RTS NOTIFY_AP U2CTS U2RXD U2TXD GND EAR_EINT 2G_ANT JTAG_EN GND VEXT28 VBAT VBAT GND U1TXD U1RXD GPIO2 LED_B GPIO1 SPK_OUTN SPK_OUTP MP3_OUT_L MP3_OUT_R GND Power Key to enable MT6260 internal PMU General Purpose I/O,For cus-
tomize./INT1 Headset Microphone detect INTFor Host/AP to wake up Expedite L10-G module. UART2 Request to send Notification for incoming call and SMS UART2 Clear to send UART2 Serial Data Output UART2 Serial data input Ground Headset Detect The signal of RF antenna input/out-
put. JTAG Strap Pin, pull high 1K to 2.8V to enable JTAG f Ground 2.8 V out Reference for external level translation Power Pins Power Pins Ground UART1 Serial data input UART1 Serial Data Output General Purpose I/O,For customize. LED control General Purpose I/O,For customize. speaker amplifier (-) (Analog) speaker amplifier (+) (Analog) headset amplifier Left headset amplifier Right Ground 1.8V~2.8V 2.8V 2.8V 1.8V 2.8V 1.8V 2.8V 2.8V 2.8V 2.8V 2.8V 2.8V Min: 3.3V, Typ: 3.8V, Max: 4.35V Min: 3.3V, Typ: 3.8V, Max: 4.35V 2.8V 2.8V 1.8V Output, VBAT_VA(KPLED) 1.8V VBAT VBAT 2.8V 2.8V 12 novatelwireless.com Pin 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Function Description Notes SDA28/GPIO SDA28/GPIO MIC1_IN-
MIC1_IN+
MIC0_IN-
MIC0_IN+
MICBIAS0 VBUS VBAT VBAT VBAT ADCIN1 Reserve Pin GPIO3 AT_READY Reserve Pin Reserve Pin USB_DM Reserve Pin USB_DM GPIO/JTRST GPIO/JTMS GPIO/JTDI GND GPIO/JRTCK GPIO/JTCK GPIO/JTDO 1.8V I/O, 2.8V I/O, 2.8V I2C Serial clock/General Purpose I/O,For customize. I2C Serial data/General Purpose I/O,For customize. 2.8V Microphone input (Headset) 2.8V Microphone input (Headset) Microphone amplifier negative input 2.8V 2.8V Microphone amplifier positive input Microphone bias 2.8V POWER INPUT POWER for VUSB Min: 3.3V, Typ: 3.8V, Max: 4.35V Power Pins Power Pins Min: 3.3V, Typ: 3.8V, Max: 4.35V Min: 3.3V, Typ: 3.8V, Max: 4.35V Power Pins 10-bit A-to-D 2.8V Reserved for debug General Purpose I/O, For cus-
tomization AT command ready signal Reserved for debug Reserved for debug Universal Serial BUS Reserved for debug Universal Serial BUS General Purpose I/O,For cus-
tomize./JTAG Test Reset General Purpose I/O,For cus-
tomize./JTAG Test Mode Select General Purpose I/O,For cus-
tomize./JTAG Test Data In Ground General Purpose I/O,For cus-
tomize/JTAG Return TCK General Purpose I/O,For cus-
tomize./JTAG Test Clock General Purpose I/O,For cus-
tomize./JTAG Test Data Out I/O 3.3V 1.8V 3.3V 3.3V 3.3V 3.3V 3.3V I/O 13 novatelwireless.com Pin 63 64 65 66 67 68 Function Description Notes SIM1_DATA SIM1_CLK SIM1_RST DAIPCMOUT DAICLK DAIRST SIM data I/O SIM clock SIM reset PCM data out PCM clock PCM RST VSIM1 VSIM1 VSIM1 I/O, 2.8V I/O, 2.8V I/O, 2.8V Table 3-1 I/O Connector Pin Assignments Analog Audio Interface The Expedite L10-G module provides analog audio interface, include speaker, microphone, and headset. Speaker Pin No. Pin name Description 29 31 SPK_OUTN SPK_OUTP speaker amplifier (-) (Analog) speaker amplifier (+) (Analog) Speaker functional specification Symbol IDC SINAD RLOAD CLOAD ICN XT Vout Parameter Min. Typ. Max. Unit Current consumption Signal to noise and distortion ratio Input level: -40 dBm0 Input level: 0 dBm0 Output resistor load (differential) Output capacitor load Idle channel noise of transmit path L-R channel cross talk Full Scale output voltage SPK_OUT 29 16 4 69 32 0.7 mA dB dB pF dBm0 dBm0 Vrms 250
-67
-66 Expedite L10-G integrate class-AB audio AMP, the following table is the maximum output power:
Maximum output power Test Condition SPK_OUTN 3.3V, 8 ohm THD+N=1%
4.2V, 8 ohm THD+N=10%
3.3V, 8 ohm THD+N=10%
Speaker reference circuit 0.87W 0.53W 1.08W 0.65W 14 novatelwireless.com Microphone Pin No. Pin name Description 40 41 42 43 44 MIC1_IN-
MIC1_IN+
MIC0_IN MIC0_IN+
MICBIAS0 Microphone input (Headset) Microphone input (Headset) Microphone amplifier negative input Microphone amplifier positive input Microphone bias MicBias output Mic Bias Output Typ. Max Unit MICBIAS0 MICBIAS0 current draw 1.9 2.2 2 V mA Microphone functional specification Symbol IDC SINAD RIN ICN Vout Parameter Min. Typ. Max. Unit Current consumption for one channel Signal to noise and distortion ratio Input level: -40 dBm0 Input level: 0 dBm0 Input impedance (differential) Idle channel noise Full Scale output voltage MIC0 29 13 1.5 69 20 1 27
-67 mA dB dB K dBm0 Vrms Microphone Type Support Expedite L10-Gcan support ECM microphone and MEMS microphone. ECM Microphone reference circuit 15 novatelwireless.com MEMS Microphone reference circuit Headset Pin No. Pin name Description 9 14 36 37 ACCDET EAR_EINT Headset Microphone Detect Headset Detect (Internal PU, no need external PU circuit) MP3_OUT_L MP3_OUT_R headset amplifier Left headset amplifier Right 16 novatelwireless.com Pin No. Pin name Description 40 41 MIC1_IN-
MIC1_IN+
Microphone input (Headset) Microphone input (Headset) Earphone functional specification Symbol Parameter Min. Typ. Max. Unit FCK Fs IDC PSNR DR VOUT THD RLOAD CLOAD XT Clock frequency Sample rate Current consumption Peak signal to noise ratio Dynamic range Full Scale output voltage MP3_OUT Total harmonic distortion 10mW at 64 load Output resistor load Output capacitor load L-R channel cross talk Headset reference circuit 32 64 70 6.5 44.1 4 88 88 0.78 48
-70 250 MHz KHz mA dB dB Vrms dB pF dB 17 novatelwireless.com Specific Absorption Rate (SAR) Guidelines Portable RF exposure evaluation must be completed on host devices that provide 20.0 cm of separation distance between the transmitter antenna and the end user. Portable Device Definition The FCC defines a Portable Device as a device having a transmitting antenna located at a distance 20cm from the user. Mobile Device Definition The FCC defines a Mobile Device as a device having a transmitting antenna located at a distance 20cm from the user. SAR Compliance European and US certification bodies require that you test Specific Absorption Rate (SAR). SAR is a measure of energy absorbed by organic tissue over a specific time. The factors that affect SAR readings are:
l output power l frequency of the radiation l proximity to antenna l antenna counterpoise l duty cycle Early in the physical design stage of the UE, the antenna and the mechanical engineering design teams must collaborate on the design to ensure that they can meet the SAR requirements. Carefully reading and understanding the FCC requirements can help designers choose the antenna type, the antenna location, and the industrial design of the UE. The placement and characteristics of the main antenna are the most critical factors affecting SAR performance. 18 novatelwireless.com 3 Tune Up Procedures Tune Up Procedure 19 novatelwireless.com Tune Up Procedure During manufacturing each device will be individually calibrated. Measurement is performed in a fully calibrated environment using an CMW500 base station simulator. The measurement procedure is outlined below:
Measurement Procedure:
1. Set the device to operational voltage and on a predefined channel in a special test mode. 2. The actual output power is measured at several power levels. 3. The gain factors of each individual device are adjusted until the target value is met. The appropriate gain control settings for each output power level are stored in each device individually (for each power level). The user has no possibility to change these settings later on. 4. The maximum gains of each individual device are adjusted and measured until the target value is met. The production target power with tolerance compiles with the maximum power in test report. Maximum Target Power for Production Unit (dBm) Mode GSM 850 GSM 900 GSM 1800 GSM 1900 GPRS 8 (1 Uplink) CS1 32.5 (+0.5/-0.7dB) 32.5 (+0.5/-0.7dB) 29.5 (+0.5/-0.7dB) 29.5 (+0.5/-0.7dB) GPRS 10 (2 Uplink) CS1 30 (+0.5/-0.7dB) 30 (+0.5/-0.7dB) 27 (+0.5/-0.7dB) 27 (+0.5/-0.7dB) GPRS 11 (3 Uplink) CS1 28.2 (+0.5/-0.7dB) 28.2 (+0.5/-0.7dB) 25.2 (+0.5/-0.7dB) 25.2 (+0.5/-0.7dB) GPRS 12 (4 Uplink) CS1 27 (+0.5/-0.7dB) 27 (+0.5/-0.7dB) 24 (+0.5/-0.7dB) 24 (+0.5/-0.7dB) 20 novatelwireless.com