FCC ID: 2AYGT-33-02 Geni Thermal Imaging Monocular

ILR-1200-2 INFIRAY LASER RANGEFINDER Specication Model Type ILR-1200-2 Inray Laser Rangender Measuring Range, m 5-1200 Accuracy, m 1 @100 Laser Wavelength, nm 900-908 Interface Battery Type C (Charge / Discharge) One replaceable 18650 battery Maximum Battery Life Used as an LRF only: 20h When used as an LRF and a power bank at the same time, it can increase the battery life of MATE by 4h IP Grade IP67 Applicable Product MATE series Dimensions, mm 886253 Weight, g 240 Components and Controls 2 6 4 1 3 1. Battery compartment cover 5 7 8 2. Laser indicator 3. Rangender lens 4. Power button 5. LED indicator 6. Type-C interface 7. Vertical direction regulation knob 8. Horizontal direction regulation knob Product Description ILR-1200-2 is a laser rangender (LRF) used with the MATE series. In addition to that, it can function as a power bank to charge MATE through the Type C cable. The LRF itself can also be charged using the power adapter and data cable of MATE. Installation with Mate The LRF is equipped with a mount which can install the LRF on the picatinny rail on the right side of MATE. Linkage with Mate Linking ILR-1200-2 to MATE for the rst time:

l Put ILR-1200-2 and MATE close to each other. l Power on MATE and briey press the Power button (4) of the ILR-1200-2 Five times consecutively to turn on the LRF. l Wait for 10s and the linkage between ILR-1200-2 and MATE will be automatically connected. l The distance value appears on the display of MATE, indicating that the linkage is successful. Note:

The LRF and MATE shall be linked within 90s after MATE is started. If the linkage is not completed within the specied time, restart MATE and repeat the steps above. Non rst time connection:

l After successful linkage once, when using the LRF again, just press the Power button (4) on the LRF, and it will complete the automatic connection between the LRF and MATE . Usage with Mate l After successful connection, press and hold the Up button on MATE for 6s can turn on/off the laser indicator on the LRF. l It is automatic and continuous ranging without any operation. l After using, press and hold the Power button (4) of the LRF for 3s to turn off the LRF, during which the LED indicator (5) will blink 3 times. Note:

When LRF is linked with Mate, the range notication function on Mate will be not available. Laser Calibration When the target position pointed by the laser indicator is not consistent with the reticle center, this function can be used to calibrate the cursor position. l Select a target 100m away, aim the reticle center of the day scope at the target, and x the position of the day scope. l Turn on the laser indicator with a long press of the Up button of MATE. l Adjust the vertical direction regulation knob (7) (leftward and rightward) and the horizontal direction regulation knob (8)

(upward and downward) until the targets directed by the laser indicator and reticle center are consistent to complete the laser calibration. l It is recommended to perform the calibration at night, because the laser indicator is more obvious in the dark. Safety Precautions l If the battery is stored for a long time, it should be partially charged. The battery can neither be fully charged nor fully discharged. l Do not charge the battery immediately after it is brought from a cold environment to a warm environment. Wait 30-40 minutes for the battery to warm up. l Do not leave the battery unattended while charging. l Charge at a temperature of 0C ~ +45C, otherwise, the battery life will be signicantly reduced. l Do not leave the battery connected to a charging device for more than 24 hours after it is fully charged. l Do not expose the battery pack to high temperature or open ames. l Connections are not recommended for external devices that consume more power than allowed. l Battery short circuit protection is provided, but any situation that may lead to a short circuit should be avoided. l Do not disassemble or squeeze the battery. l When the battery is used below zero, its capacity will decrease, which is normal. l Do not use the battery at temperatures higher than those shown in the table, or else the battery life may be reduced. l Please keep the battery out of the reach of children. CAUTION LASER 3R P<5mW, 650nm EN 60825-1:2014/A11:2021 Legal and Regulatory Information Wireless transmitter module frequency range:

WLAN: 2.412-2.472GHz (For EU) Wireless transmitter module power < 20dBm (only for EU) Hereby, IRay Technology Co., Ltd. declares that the radio equipment type ILR-1200-2 is in compliance with the Directives 2014/53/EU, 2011/65/EU and RER 2017 (SI 2017/1206). The full text of the EU&UK declaration of conformity is available at:

www.inrayoutdoor.com. User information on the disposal of electrical and electronic devices (private households) 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. Regulatory information USA FCC ID: 2AYGT-33-02 Labeling requirements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information to the user Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IRay Technology Co., Ltd. Add.: 11th Guiyang Street, YEDA, Yantai, P.R. China Tel: 0086-400-998-3088 Email: infirayoutdoor@infiray.com Web: www.infirayoutdoor.com

Date: 03-21-2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: 2AYGT-33-02 Dear Sir or Madam,

[IRay Technology Co., Ltd.] certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing covered equipment. If you have any questions, please contact us. Sincerely, Contact name: Peng Zhang Company name: IRay Technology Co., Ltd Address: 11Guiyang Street, YANTAI Economic and Technological Development Area, Yantai, ShandongP.R.China E-mail: peng.zhang@raytrontek.com Tel: 0086-0535-3410600

To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 03-21-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AYGT-33-02 IRay Technology Co., Ltd. certifies that, as of the date of the filing of the application, Visir lnc. is our designated U.S. agent for service of process for the above referenced FCC ID. IRay Technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Visir lnc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: Visir Inc. Address: 700 International Pkwy Ste 102, Richardson, TX 75081 Contact Person: Tao Huang Tel.: (510)366-2707 Email: thuang@visirinc.com FRN: 0032684243 Sincerely,

[Insert U.S. agent company name]

(U.S. agent company name printed name)

(U.S. agent company name signature) Visir Inc. Tao Huang

[Insert applicant name]

(Applicant printed name)

(Applicant signature) IRay Technology Co., Ltd. Peng Zhang Rev 1/26/2023

IRay Technology Co., Ltd. Date (2023-03-30) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request FCC ID: 2AYGT-33-02 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, IRay Technology Co., Ltd. hereby requests permanent confidential treatment of information accompanying this application as outlined below:

SCH&PCB layout BOM Block Diagrams Operation Description IRay Technology Co., Ltd. also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of (can list up to 180) days:

Internal Photos External Photos User Manual Test Set-up Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name: Peng Zhang Title: Quality Supervisor