CMN-851 Installation Manual Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION 1. Compliance statement and notification
<FCC / IC>
Declaration of Conformity Product Name: WLAN Module Model Number: CMN-851 This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of this device. RF exposure compliance:
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequencyRFExposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequencyRFExposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation MPE. But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from persons bodyexcluding extremities: hands, wrists, feet and ankles.
< FCC >
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 1/9 instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an AC outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. In according with 47 CFR Part15.407 (e) U-NII devices operating in 5.15-5.25GHz frequency bands are restricted to indoor operations only. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: CKECMN851
< IC >
Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. 2/9 This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). This device has been certified for use in Canada. Status of the listing in the Industry Canadas REL (Radio Equipment List) can be found at the following web address:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Additional Canadian information on RF exposure also can be found at the following web address:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Canada, avis d'Industry Canada (IC) Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement. Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mobiles (les antennes se situent moins de 20 cm du corps d'une personne). Ce priphrique est homologu pour l'utilisation au Canada. Pour consulter l'entre correspondant lappareil dans la liste d'quipement radio (REL - Radio Equipment List) d'Industry Canada rendez-vous sur:
http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Pour des informations supplmentaires concernant l'exposition aux RF au Canada rendez-vous sur :
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Information to Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains IC: 768B-CMN851 3/9 This radio transmitter IC: 768B-CMN851 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 TAIYO YUDEN AH 104N2450D1 Chip Antenna 2.1dBi in 2.4GHz 2.4dBi in 5GHz Note: The Cable (I-pex type) connects WLAN module and Chip antenna.
<R&TTE>
CE Marking:
Please describe the following sentences to the label or the user manual of the product in each language in the sales country:
Hereby, Japan Radio CO., Ltd. declares that this CMN-851 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. 4/9 2. Hardware Specification 2.1 Radio Specification ITEM Communication Standard Access Control Frequency Band and Operating Channels Table 2-1 Radio Specification Descriptions IEEE802.11b/g/n IEEE802.11a/n CSMA/CA U.S.A24122462MHz 11 channels111 Canada24122462MHz 11 channels111 Europe24122472MHz 13 channels113 Japan24122472MHz 13 channels113 U.S.A5180-5320MHz 5500 5700MHz 19 channels Canada5180-5320MHz 5500 5700MHz 19 channels Europe5180-5320MHz 5500 5700MHz 19 channels Japan5180-5320MHz 5500 5700MHz 19 channels 20MHz OFDM 802.11b1,2,5.5,11Mbps 802.11g6,9,12,18,24,36 Channel Space Modulation Data Rates Supported 5MHz DSSS / OFDM 802.11b1,2,5.5,11Mbps 802.11g6,9,12,18,24,36 Antenna Connectors
,48,54Mbps
,48,54Mbps 802.11nHT20/40, MCS015 U.FL or equivalent, 2pcs. 802.11nHT20/40, MCS015 2.2 Power Supply Table 2-2 Power Supply PARAMETER Supply Voltage (Vcc) Operating Current MIN 3.13
TYP 3.3 0.74 MAX UNIT 3.47 0.93 V A COMMENTS Supply regulated voltage Condition: Vcc=3.3V 5/9 2.3 Host Interface 2.3.1 Electrical Interface PCI-express mini-card Rev1.1 2.3.2 Host Interface connector pin layout Fig.1 Host Interface Connector pin layout 2.3.3 Pin assignment and signal descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Signal name Signal type Descriptions
#WAKE 3.3Vaux COEX1 GND COEX2 1.5V CLKREQ#
UIM PWR GND UIM_DATA REFCLK-
UIM_CLK REFCLK+
UIM_RESET GND UIM_VPP Reserved UIM_C8) GND Reserved UIM_C4) W_DISABLE#
GND RESET#
PERn0 3.3Vaux PERp0 OD I/O I/O OD I I IH/OH IH O O
-PCIe service a function-initiated wake up event request
-Open Drain Output NC PCIE reference clock request NC NC PCIE differential reference clock(100MHz) NC PCIE differential reference clock (100MHz) NC NC NC NC PCIE reset PCIE Differential transmit PCIE Differential transmit 6/9 Pin No. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Signal name Signal type Descriptions GND GND
+1.5V GND SMB_CLK PETn0 SMB_DATA PETp0 GND GND USB D-
GND USB D+
3.3Vaux GND 3.3Vaux LED_WWAN#
GND LED_WLAN#
Reserved LED_WPAN#
Reserved
+1.5V Reserved GND Reserved 3.3Vaux I IH/OH GND NC GND NC PCIE Differential receive NC PCIE Differential receive GND NC NC GND NC GND NC NC NC NC NC NC GND NC Signal type Description Input Output Open Drain Pull up I O OD H 2.4 Environmental Conditions ITEM Operating Temperature Operating Humidity MIN 0 20 TYP MAX UNIT degC
%Rh Non condensing
+50 95 COMMENTS 7/9 2.5 Mechanical Specification Size
: 30(W)x26.8(D)x4.75(H)mm Weight : Approx. 5g Label Fig.2- Outline Drawing 8/9 3. Installation
(1) Please insert the module in the host side connector firmly. insert the module
(2) Please connect the antenna cables with ANT-A and ANT-B 9/9