FCC ID: VEPUBC-CO1 BarkWise

Included In Your Package BarkWise bark control device Nylon dog collar Remote control Please use a CE or EN 60950 approved adapter for charging. The adapter output should be DC 5.5V, 0.5A. Before getting started Getting Started What is ultrasonic sound?

Ultrasonic sound frequencies are outside the range of human hearing. However, dogs can hear ultrasonic sound which is attention grabbing and irritating to dogs. Ultrasonic sound has been used for over a century to safely and humanely train dogs. 1. Charging the BarkWise The BarkWise comes with a charger. Simply plug this into the collar and plug the adapter into an outlet. The blue LED light will indicate that BarkWise is charging. The red LED flashes when BarkWise needs charging (charge time is approx. 2hrs). How does vibration work?

BarkWise vibrates in response to your dogs barking. This cre-

ates a slight annoyance and takes the dogs focus off of barking. How long will training take?

Bad habits are sometimes hard to break. While some dogs may take longer, most will start taking to the training within two weeks. What size of dogs can BarkWise be used on?

There are currently no restrictions for what size of dogs the BarkWise can be used. However, the collar strap can fit dogs with a neck size of 6 up to 24. Is BarkWise safe?

Absolutely. Unlike other training collars such as shock, BarkWise uses safe and humane technology to curb your dogs barking. How BarkWise works BarkWise detects barking with an internal microphone and responds by emitting combinations of ultrasonic or audible sound and vibration. The combinations create an irritating sensation that disrupts barking. After a short training period, your dog will begin associating his barking with this annoyance and learn to be quiet. Its completely safe and humane bark control. 2. Turn the BarkWise on /off The power button is located on the top of the unit. Power it ON by pressing and holding the button for 3 seconds. The unit will beep 3X with a flashing blue light. BarkWise is now activated. Power OFF by pressing and holding the button for 3 seconds. It will beep 1 time and the red light will flash. Blue LED Red LED Power Button 3. LED lights Blue LED Indicator: primary indicator light that is emitted at various operational settings of the unit, e.g. vibration, ultrasonic, and audible. Red LED Indictor: enabled during the power OFF stage of the unit BarkWise Instruction Manual 4. Remote control Press the button to activate BarkWise (a blue LED light will indicate the button is pressed). This will activate the unit based on your control panel settings. Use the remote control up to 75 feet away. 5. Control panel 1 2 3 4 7. Fit BarkWise on your dog 1. Make sure your dog is standing and is calm. 2. Place BarkWise underneath your dogs neck and ensure the vibration prongs are touching his skin. 3. Adjust the collar so that it is snug but not restricting. You should be able to place 1 finger comfortably between the nylon strap and your dogs neck. 4. Slip the loose end of the collar under the attached loop. 4. After wearing the collar for a short time period, recheck to see if its fitting properly. Continue to do this periodically as your dog becomes more comfortable with BarkWise. 6. If the collar length is too long, mark the trim length with a pen, then remove the collar. Cut the excess and carefully seal the frayed end with a flame. Fit the collar to your dogs neck and tuck in the strap using the provided loop. Were Here to Help Toll Free: 1-800-657-8214 Outside US: 1-541-245-4488 Website: www.ultimatebarkcontrol.com Email: customerservice@goodlifellc.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den comprom-

ettre le fonctionnement. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Caution Changes or Modications not expressly approved by the party responsible could void the users authority to operate this device. Warning Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. This product need power supply by adapter that can meet LPS. The maximum operating temperature is 45C. 1 2 3 4 Bark sensitivity slider Allows you to adjust BarkWise sensitivity to barking. This ranges from low to high. REM (Remote Only or Mic) Choose between having Barkwise activate when your dog barks (UP) or only by pushing the button on the included remote (DOWN). AUD (Audible / Ultrasonic Mode) Use either Ultrasonic mode (UP) or Audible mode (DOWN) for training your dog. Audible mode is useful for hearing the device activate to your dogs bark, letting you know that the bark sensitivity slider is set correctly. VIB (Vibration / No Vibration) Select BarkWise to vibrate (DOWN) or not vibrate (UP) in response to barking. 6. Testing Turn the sensitivity dial all the way up and power the unit ON. Clap your hands to mimic the sound of barking. Depending on what setting the unit is on, a flashing blue light will let you know the unit is working. 2014 Good Life, Inc. DESIGNED IN OREGON MADE IN CHINA BarkWise Instruction Manual

Flat A, 7/F., Mai On Ind. Bldg., 17-21 Kung Yip Street, Kwai Chung, Hong Kong. K-mark Industrial Limited. DATE :2014-4-03 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Hank Yan of Global United Technology Services Co., Ltd. 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District Shenzhen Guangdong to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with K-mark Industrial Limited. and Flat A, 7/F., Mai On Ind. Bldg., 17-21 Kung Yip Street, Kwai Chung, Hong Kong. Dated this Agency agreement expiration date:

By:

Day of 4/03/2014 Richard Tam 4/03/2015

Signature Project Manager Title:

On behalf of :

Telephone:

K-mark Industrial Limited. 852 2741 3165 Printed