Kapsch TrafficCom IVHS Janus HOTPass Interior Transponder Mounting Instructions The HOTPass interior transponder mounts on the vehicle windshield. The preferred mounting location is between the roofline and the rear view mirror post. If there is not enough room in the preferred mounting location to accommodate the HOTPass transponder, the transponder can be mounted beside the rear view mirror post. The HOTPass transponder is secured using 3M Dual Lock fasteners. HOTPass Interior Transponder Mounting Instructions 1. Select a mounting location on the front windshield. The HOTPass transponder should be mounted in., but no more that 2 in. from the roofline. The preferred mounting location is between the roofline and the rear view mirror mounting post, with a minimum of in. between the transponder and the rear view mirror post. Requirements n For reliable operation of the transponder, the vehicle must be equipped with only one transponder while passing through a toll facility. Other transponders present in or on the vehicle must be switched off or enclosed in an RF shield. n The mounting location must provide direct line-of-sight communication between the transponder and the toll facility overhead antenna. n Do not mount the HOTPass transponder on vehicles:
u with non-metallic roofs. u with windshields covered in RF-blocking material (ex. metal oxide). u with a metallic center windshield dividing post. u without center-mounted rear view mirrors. n Handheld mobile communication devices must not be located within 12 in. of the transponder. n Metal objects (except for the rear view mirror and the roof ) must not be located within 6 in. of the transponder. n HOTPass transponders cannot be used where local regulations prohibit mounting transponders on the windshield. n Apply Dual Lock fasteners in accordance with 3M document. 70-0709-4029-4. in. preferred, 2 in. maximum orientation arrow 4. Remove the protective backing from the two Dual Lock fasteners. roofline 3M Dual Lock strips
. e c i t o n t u o h t i w n o i t a r e t l transponder in. minimum rear view mirror post Preferred Mounting Location - Front View HOTPass Transponder - Rear View 2. If there is insufficient space in the preferred location, select an alternate mounting location beside the rear view mirror post:
in. preferred, 2 in. maximum roofline 5. Firmly press the HOTPass transponder against the windshield in the mounting location, ensuring the orientation arrows are pointing skyward. Maintain pressure for 15 seconds to ensure a good bond. 6. Remove the transponder by lifting any corner with sufficient force to separate the Dual Lock strips. Do not reuse the Dual Lock strips after removing them from the windshield. Obtain new strips as required. orientation arrow rear view mirror post in. min., 1 in. max Alternate Mounting Location - Front View 3. Two 3M Dual Lock on the back of the HOTPass transponder are used to mount the transponder to the windshield. Prepare the mounting location in accordance with 3M document 70-0709-4029-4. Kapsch Group The Kapsch Group and its entities Kapsch TrafficCom, Kapsch CarrierCom and Kapsch BusinessCom are specialised in the future-oriented market segments of Intelligent Transportation Systems (ITS) and Information and Communication Technology (ICT). Kapsch. Always one step ahead. Kapsch TrafficCom IVHS | 6020 Ambler Drive | Mississauga, Ontario L4W 2P1 | CANADA | Phone +1 905 624 3020 | Fax +1 905 625 6197 54 S. Commerce Way, Suite 100 | Bethlehem, PA 18017 | Phone +1 610 419 1479 | Fax +1 610 419 1489 E-Mail ktc.ca.info@kapsch.net | ktc.us.info@kapsch.net | www.kapsch.net a o t t c e b u S j
. d e v r e s e r s t h g i r l l A
. S H V I m o C c i f f a r T h c s p a K 1 A v e R 2 2 0
0 5 8 1 0 8