UBIQUITY Transponder User Instructions Document A316000-828 ie TRTOSeCo MAU etre Figure 3: J-Box connections
(option) 12 Vde weee] (Option) adapter onboard computer BOER R BRR 41708 bus J1939 bus BBM ounting Instructions
| status of the transponder according to data received | Please verify the from a reader and may be a different scenario for each connector orientation.
| yellow | agency. (Your service provider should give this "
| green ; information to you in a separate instruction sheet.) 1 fr tener a ice nen ON A ti Re a a i audible tone provides a BEEP signal when required he metal band on the onnector.is:on the Block diagrams of typical application configurations Figure 1: Basic installation:
The transponder works best when mounted in the position shown in the photo above. The transponder is centered on power/serial the headliner. The LEDs are at the bottom. Do not position 42 Vde _ port the transponder or the interconnection wiring so as to adapter obstruct your normal view of the roadway. The transponder plug power/serial port wiring % typically routed in a manner that hides it in the headliner. IMPORTANT Notes:
e Incorrect mounting position of the transponder may result in failure to communicate with the reader. e The power/serial adapter must not remain on top of the Figure 2: Basic installation + onboard computer dashboard where it might overheat in the sun. Notes about using the Dual Lock strips that are power/serial fastened on the back of the transponder... 1. Thoroughly clean and dry the glass surface where the transponder is to be mounted on the inside of the windshield. 2. Carefully emove the protective backing from the Dual Lock mounting strips. power/serial 3. Ensure that the transponder is oriented as shown in adapter 9pingr" the photo above . 4. Firmly press the transponder against the windshield. 2002 MARK IV INDUSTRIES LTD. Revision A, Issue printed on 7/8/2002 3:40 PM, filename: Ubiquity tag uscr guide RevA.doc the windshield interior with the top edge about 2 inches below
~~ Photo #2: J-Bus J-Box-connectors UBIQUITY Transponder User Instructions Document A316000-828 5. Maintain firm pressure for about 15 seconds to achieve a good bond. 6. After this, the transponder may be removed from the Dual Lock strips as often as required. Always press the transponder back firmly onto the Dual Lock strips. 7. Make the connections to the transponder as shown in the power/serial port connection section on this page. Choose the drawing that suits your specific application.
| Equipment identification photos Photo #1: Basic installation power supply connectors:
transponder connector |
plugs into the transponder
- power/serial port 12\Vde adapter plug plugs into the cigarette |
lighter socket power /serial adapter Specifications Protocol compatibility 1. IAG 2. TDMA V6 3. Sandwich specification IEEE 1455 +) 4, Title 21 Power supply A 5 Vdc power tap extracted from the vehicle 12 Vdc power provides the power supply for the transponder. Life 6 year operating life measured from delivery date of transponder from the factory. Batteries are not required. Durability of the case meets SAE 1455 recommendations. Operating Temperature Range All demonstration transponder performance specifications apply over the temperature range -20C to +70 C unless otherwise specified. The power/serial adapter supplied in the transponder demonstration package is rated at 0 to +85 C. Maximum Case Temperature 115 C as per SAE J1455. The transponder case does not deform or become permanently damaged at this temperature. Storage Temperature Range The transponder can be stored safely within -40 to 85 C Humidity The transponder withstands 5 to 90% relative humidity, non-
condensing. Vibration The transponder performance does not degrade when subjected to 1.5g vibration 5 through 1000 Hz in any plane for 3 hours as per test method SAE J1211. RF Safety The transponder transmitted energy does not exceed the RF safety requirements as specified in IEEE C95.1-1991. Applicable RF Standards - -
The transponder meets FCC Parts 15 and 90 and Industry Canada RSS 137. Mounting Use the 3M Dual Lock strips supplied to mount the transponder to the inside of the vehicle window as described in the mounting instructions section above.. Metallized Windows The transponder cannot be used in vehicles equipped with either metalized windshields or metalized sunscreen appliqus. Customer Access There are no customer serviceable components inside.
{The above specifications are subject to change without notice.)
| us electronic toll collection weigh station bypass /mainline screening e CVISN applications mobile commerce Document revision RevA 4-July-02 original release 2002 MARK IV INDUSTRIES LTD. Revision A, Issue printed on 7/8/2002 3:40 PM,filename: Ubiquity tag user guide RevA.doc