DESCRIPTION SET UP GPS TRACKER KRG GPS tracker is designed to send geolocalized alerts. GPS tracker is a fully supervised low-current detector including an advanced Sigfox protocol. To activate the GPS Tracker, press the button during 1 to 2 seconds. LED will blink as described below. 1. Red LED on the tracker flashing every 1 second. 2. Green or red (depending on the configuration) LED lights on during 5 seconds. 3. The configuration is set up. When the device restarts after a hardware or software reset or when it is plugged to be recharged after a shutdown due to empty battery, it will follow steps described before. SEND AN ALERT BATTERY CHARGE DIMENSIONS To send an alert, push button during 1 to 2 seconds. 1. Green LED will flash every second during 1 minute. 2. Green LED lights on during 3 seconds to indicate an alert is sent. To cancel the alert, push the button in the following 30 seconds during 10 seconds without interruption. Green LED will stop flashing to inidicate alert has been well canceled. 59 mm indicate To low
(<20%), battery red LED will flash every 10 seconds. 59,1 mm 21,6 mm 1. Put the GPS tracker into the cradle to charge it. 2. Green LED will start flashing every 3 secondes. 3. When the green LED stops flashing and is continously turned on, the device is fully charged (around 2h). SPECIFICATIONS Sigfox Zone RCZ1 (Europe) RF Specification Sigfox Class 0 Product Size 59,1mm(L) x 59mm(W) x 21,6mm(H) Button LED One big button for emergency usage Dual color LED Green and Red Connector 1. One MicroUSB connector for battery 2. One cradle to charge easily the tracker charging IP65 IP Rating Battery Rechargable lithium. Battery 3.8V 630mAh Battery life
> 18 months Operation temperature
- 10 / +50c, 0-90% RH non-condensing Storage temperature
- 20 / +70c, 0-90% RH non-condensing Geolocation Geolocation can not be fully guaranteed in the following conditions : indoor, in trafic. Federal Communication Commission Interference Statement Regulatory Notices:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies the
(2) following this device must accept any interference received, including interference that may cause undesired operation. 15 device interference, conditions:
of may Operation to and harmful subject Rules. cause with FCC Part This two not the
(1) is IMPORTANT NOTE:
Radiation Exposure Statement:
The product with comply an uncontrolled environment and are safe for intended operation as described in this manual. as The possible is available. reduction set far function the output be device if lower be such can if exposure can the exposure portable achieved product further power forth body limit from kept user the the set for US RF RF or as to This transmitter must antenna or transmitter. other not be co-located or operating in conjunction with any Industry Canada statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) Lappareil ne doit pas produire de brouillage;
(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. Dclaration d'exposition aux radiations: