SP-HF2800BT MODE VOL+
VOL-
Quick InstallationGuide Copyright 2019 KYE SYSTEMS CORP. Genius web : www.geniusnet.com OEM/ODM : www.kyecom.com KYE Systems Corp.
#492, Sec. 5, Chongxin Rd., Sanchong Dist., New Taipei City 24160, Taiwan Tel: 886-2-2995-6645 Fax: 886-2-2995-6649 Email:sim@geniusnet.com.tw Email:csd@geniusnet.com.tw (Tech. Support) http://www.geniusnet.com KYE International Corp. (USA & Canada) 12675 Colony Street, Chino, CA 91710, USA Tel: 1-626-226-2678 Tel: 1-800-756-4115 (Toll Free Line) Fax: 1-626-226-2679 http://www.geniusnetusa.com http://www.geniuseshop.com FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. MODE VOL+
VOL-
English English English English 1.1 Panel Button Function 1.2 Remote Button Function LED Display LED shows Bluetooth icon and blinks Description LED shows next track Function Icon Press for next track Status Next track 2.0 LED Display Description Speaker Status Power on LED Status LED shows Bluetooth icon and blinks All display shut off LED shows Bluetooth symbol LED shows LINE symbol LED shows USB symbol LED shows Bluetooth working status Display LINE symbol Display USB symbol LED shuts off Power off Pairing finished LINE USB 3.0 Function Q & A Searched Device Part Number Is there sound notification?
Is voice notification available?
Will the device enter pairing mode after it fails booting re-connecting?
Will the device enter pairing mode after disconnection?
IS USB drive always primarily played?
4.0 Operation Process 1. Connect power plug and audio line. And set up the speaker system. SP-HF2800BT One beep when TWS is paired NA Yes. USB drive will be primarily operated when connected. Yes Yes track; Press the button on panel or remote to play the next track. User can short press the VOL+ on panel or remote to increase volume; long press the VOL+ to increase volume continuously. And short press the VOL- on panel or remote to decrease volume; long press the VOL- to decrease volume continuously. 3. The PAIR and TWS buttons on remote are only workable under Bluetooth status. 4. TWS Operation Function Under Bluetooth status without any device paired, press the power button on remote or long press the MODE button on speaker panel to turn on the speaker. For the other speaker, run the same process. Long press on panel or short press TWS button on remote, the main speaker will beep. Then the two speakers will star pairing. After pairing is finished, the two LEDs on two speakers will become constantly blue. Then user can open Bluetooth device to run search mode and pair with SP-HF2800BT. After the pairing is done, it is ready to play music. 2. To turn on the speaker, you can either press the power button on remote or long press the MODE button on speaker panel. After it is turned on, the LED screen becomes blue and blinks; now it is ready to run pairing. After pairing process is finished, the LED is constantly blue. Now the system is ready to play music. 5. Under power-on status, short press LINE on remote or button on panel, the LED will show constant LINE. Connect audio device with audio line, and it will ready To stop the music, press the on panel or remote. Press it again, the music to play music. To stop the music, press the on panel or remote. Press it again, would continue. Press the button on panel or remote to play the previous the music would continue. Status Function Button Operation Long press button Short press button Short press button(with USB drive connected) When USB drive is plugged in, the drive would be primary button Long press Press VOL+ to increase volume Press VOL- to decrease volume Short press play/pause button Long press play/pause button Press for precious track Description LED becomes blue and blinks LED shows LINE and play icon LED shows USB and play icon LED shows USB and play icon. It plays from 00:00. LED shuts off and stop operation. LED shows volume level, maximum is 30 LED shows volume level, minimum is 00 LED shows pause icon LED becomes blue and blinks with sound LED shows previous track Turn on Turn on Power on Line Status 1 Power on USB Status Power on USB Status Power on Turn off Increase 2 Power on Volume 3 Power on Decrease Volume Play music 4 Pause Bluetooth Status TWS 5 Power on 6 Power on Previous track Next track Function Icon Status Turn on/off Power on TWS Power on PAIR Power on Power on Power on Turn off Increase Volume Decrease Volume Pause TWS Previous track LINE USB Long press MODE button Press VOL+ to increase volume Press VOL- to decrease volume Short press play/pause button Long press play/pause button Description Press to turn on or turn off Press TWS to enter TWS paring status. Keep press for 3 seconds to disconnect paired device(effective under Bluetooth status) Press PAIR to disconnect currently paired device and enter search mode(effective under Bluetooth status) Press Bluetooth to enter Bluetooth status. Press LINE button to enter LINE input status. Press USB to enter USB status.(with USB drive connected) LED shuts off and stop operation. LED shows volume level, maximum is 30 LED shows volume level, minimum is 00 LED shows pause icon LED becomes blue and blinks with sound Press for next track LED shows next track Press for precious track LED shows previous track English English Both the and buttons are not workable under LINE status. The two buttons are only workable when under Bluetooth status or under USB drive User can short press the VOL+ on panel or remote to increase volume; long press the VOL+ to increase volume continuously. And short press the VOL- on panel or remote to decrease volume; long press the VOL- to decrease volume continuously. 8. Primary Operation operation. You can short press the VOL+ on panel or remote to increase volume;
Under any circumstance, the speaker system will enter USB play mode when a USB long press the VOL+ on panel or remote to increase volume continuously. And short press the VOL- on panel or remote to decrease volume; long press the VOL- on panel or remote to decrease volume continuously. 6. Both the and buttons are not workable under LINE status(panel and remore) 7. Under power-on status, when there is USB drive connected, short press USB on remote or MODE on panel, the LED will sows USB symbol and play music from 00:00. When the music is been played, press the on panel or remote to stop playing. Press it again, the speaker would continue playing music. Press the button on panel or remote to play the previous track; Press the button on panel or remote to play the next track. drive is connected. 9. MODE Loop:
When there is no USB drive connected, the speaker system will enter a Loop mode of Bluetooth and LINE cycle. When USB drive is connected, the Loop mode turns into a cycle of LINE-> USB->Bluetooth pattern. When the cycle goes into Bluetooth mode, if there is a device paired before, it will connect the device automatically. If there is no device paired before, the system will enter pairing mode. When the cycle goes into USB mode, the speaker will continue to play the track which was played last time.