LCD 563LE Users Guide Benutzerh2iidbuch Manuel dutilisation Guida Utente Guia del Usuario Manual do preprietario Handleiding Please read this manual carefully before operating your set Retain it for future reference. Reeord model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. wmenapess at FCC Warning Class B Computing Device |
Information to the User This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential tostal-
lation. This equipment generates, uses, and can radiate radio frequency energy and, if not instalicd and used in accordance with the instructions, may Cause harmful interference to radio communications. However, there is no guarantce that interference will not occur in a particular installation. If this equipment does cause interference to radio of television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving anteona.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the deaier or an experienced radio/TV technician for help and for additional suggestions. The user may find the following booklet prepared by the Federal Communica-
tions Commission helpful: How to Identify and Resolve Radio-TV intertercnce Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4. FCC Warning The user 1s cautioned that changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded cables must be used. Introduction The FLATRON LCD 563LE Flat Panel Monitor has an active matrix TFT
(Thin-Film Transistor) LCD (Liquid Crystal Display). This monitor is designed for use in small working areas or for those who need more working space on the desk. a ce a Oo ra ir Features Tie FLATRON LCD 563LE is 4 15.0-inch (15.0 inches viewable) intelhgent roicropro-cessor based monitor. a Wigtally controlled auto-scanning is done with the rracioprocessor tu Honzontal sean frequencies between 31 and 61kHz, and vertical scan frequenciss oetween 56 and /5Hz. 2 (he microprocessor-based digital controls allow you to adjust conveniently a atrals. by using the OSD (On Screen GIs play). Lp to 1024x768, and has a wide viewing anaie of #7 a
{+55 dearees vertical. shipped wath 14 factory pre-proqrani to rmernory modes. a cho aed olay capapiity ? Supported by your sy tert alte pronto ters (Po) 2 function *
Gomohant with: thie follovweng regulated specihuathoms
* Ser detailed information, please roter fo the Reference Guide crovidiet o Connecting the Monitor On the back of the monitor are two plug-in connections; one for the AC power cord, and the other for the signal cable from the video card.
@ Power off both the monitor and PC,
@ Connect the 15 pin VGA connector of the supplied signal cable to the output VGA video connector on the PC and the matching input connector on the rear of the monitor. The connectors will rnate only one way. If you cannot attach the cable easily, turn the connector upside dawn and try again When mated, tighten the thumbscrews to secure the connection.
@ Locate the appropriate MAC to VGA adapter block at your local computer store. This adapter changes the high density 3 raw 15 pin VGA connector to the correct 15 pin 2 row connection to mate with your MAC. Attach the other end of the signal cable to the side of the dlock wit GS rows. Connect the attached adapter block/siqnal cable to tne video output on your MAC. Connect the plug from the AC-DC adapter into tie cormector on the display unit. @ Connect one end of the AC power cord into the AC. DC a dapter.@
Plug the other end into 4 properly groundec dt three prong AC outiet. oO
@ Power on the PC, then the monitor.
@ |i you see the NO SIGNAL message, check the signal cable and connectors.
@ After using the system, power off the monitor, then the PC. IBM PC MACINTOSH pee TTT SSS om aH Signal Cable Power Cord
@ *NOTE : If you.see the OUT OF AC-DC adapter RANGE message, check to:make sure your system is set to one of the factory preset modes. (see page A8):
Location and Function of Controls Front View Power Indicator Power Button AUTO/SET Button va/4> Buttons VESA wall! mounting Rear View Connected to another object
(stand type and wall-mounted type - optional) Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores O-e-B NOTE : This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad. Control Panel Function Front Panel Controls Va/<4> Buttons Power Button AUTOISET Button Power (DPMS) Indicator __Control ee ee ee Functi foe 3h ne saleable eI YEH ose OSD Button Use this button to enter and from the on
(caametnannial . screen display (OSD). cae va/<4> Buttons Use these buttons to choose or adjust items in 8 the on screen display.
<Shortcut Keys>
. + Brightness and Contrast can be adjusted directly without Th 100 entering the On Screen Display (OSD) system. Touch Oc O10 the W/a/4/) buttons to adjust the settings and then ye the OSD button to save all changes. The Brightness
= and Contrast functions are also available in the On Screen Display (OSD) menu. Use this button to enter a selection in the on screen display.
* AUTO adjustment function Touch the AUTO/SET button before using OSD menu. This button is for the automatic adjustment of the screen position, clock and phase. Note: Some signal from some graphics boards may not function property. If the results are unsatisfactory, adjust your monitors Position, Clock and Phase manually.
= Power (DPMS) This indicator lights up green when the Indicator monitor operates normally. If the monitor is in DPM (Energy Saving) mode (stand-by/
suspend/power off), this indicator color changes to amber. Power Button Use this button to turn the monitor on or off. On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE RS ee Allow the monitor to stabilize for at leas nutes before making image adjustment. ho make adjustments in the On Screen Display, follow these steps. AUTO/SET a
Vv A < >
Ly L_g_ yocess a control, use the wa Buttons. Wher the icon you vail becomes highlighted, press the AUTO/SET Button. Lise The wWa/<4b Buttons to adjust the tern to the desired level oust the changes by pressing the AUTO/SET Button. 1 Press the OSD Button, then the main ineniu of the OSD anpears Exit te OSD by Pressing the OSD Button On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items that are shown on the Menu. OSD Adjust Description CRED = inne GREEN Initiitt:
BLUE tit. PRESET RED GREEN BLUE a Brightness Used to adjust the brightness of the screen. Contrast Adjust the display to the contrast desired. 9300K/ 6500K To appear the displays color temperature.
* 9300K: Slightly bluish white.
* 6500K:Slightly reddish white. To set your own color levels. To set your own color levels. To set your own color levels. Vertical Position To move image up and down, Horizontal Position To move picture image left and right. On Screen Display(OSD) Selection and Adjustment CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. LANGUAGE To choose the language in which the control names are displayed. LANGUAGE F ENGLISH OSD POSTION +[m]
PSEDTIME "> 0H | OSDPOSITION To adjust position of the OSD window
; 1024x768/70Hz * on the screen.
"PRESET MODE ELAPSED TIME To display the use time of monitor Video Memory Modes The monitor has 30 memory locations for display modes, 14 of which are factory preset to popular video modes. Display Modes (Resolution) Display Modes (Resolution) 1 VGA 2 VGA 3. VGA 4 MAC 5 VESA 6 VESA 7? VESA 8 VESA 9 VESA 10 VESA 11 MAC 12 VESA 13. VESA 14. VESA Note: [his CO montor has beer pre-adyusted to the video mode of 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 Ve 1074x768 @/5H 2. User Modes Modes io 30 are empty and can accept new video data. If the monitor dete 4 new video mode that has not been present before or is not one of the preset modes, it stores the new mode automatically in one of the empty modes Startiria with mode 15, Ihyou use up the 16 blanik rmodes and stil have more new video modes, the Horizontal Freq.(kHz) 31.47 31.47 31.47 35.00 37.86 37.50 35.16 37.88 48.08 46.88 49.72 48.36 56.48 60.02 Vertical Freq.(Hz) 70 70 60 67 73 75 56 60 72 15 15 60 70 75 monitor replaces the information in the user modes starting with mode 15 4 Troubleshooting Check the following before calling for service. Display Position is incorrect. a Push the AUTO/SET Button. a if the results are unsatisfactory, adjust the image position using the H position and position icon in the on screen display. On the screen background, vertical bars or stripes are visible. a Push the AUTO/SET Button. a ff the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK Icon in the on screen display. Any horizontal noise appearing in any image or characters are not clearly portraid. a Push the AUTO/SET Button. m if the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. NO SIGNAL message. a [he signal cable is net connected, or is loose. Check and secure the connection, OUT OF RANGE message appears. Picture is blank. w [he frequency of the signal frorn the video card 's outside the operating range of the moniter, Horizontal Frequency: 31kHz-61kHz Vertical Frequency: 56Hz-75Hz
(use the giaphics board's ublity software to change he requency setting (Reer to the manual for draphies board)
*You can change *he setup to the supported resolution using the Safe Mode (Press the FB key during booting "he system). The power LED is illuminated amber. w [he monitor is in its display power management mode. a [here ts no active signal coming from the PC. a [he signal cable is not fastened securely. mw Check the computer power and graphics adapter configuration. The monitor doesn't enter the power saving off mode (Amber). a Computer video signal is not VESA DPMS standard. Ether the PC or the video controller card 1s not using the VESA DPMS power management function. o Specifications Displa Type 15 Ginch GE. Ten) Flat Panel Active matrx. FT LCD, yp sn natrix ul Ant-Glare coating Viewable Size 15.0inch (38. ler) Pixel pitch 0.297 x 0.297 mmr Truecolor FLATRON LCO)563LE - 16 milhon color Sync Input Horizontal Freq. 31 -61KHz (Automatic) _ ee Vertical Freq. 56 - 75Hz (Automatic) Input Form LVDSbit) _ Signal Input 15 pin Sub Connector Video Input Display Area 304 x OP Brn / 12.0 x 9.0inch Input Form Separate, ROB Analog, 0./l4p-p/f5ohm, Positive Resolution VESA 1024 x /68/ 75Hz max :
Power Normal GW Consumption Stand-by/Suspend < SVV - :
Power Off SOV :
Dimensions Width 38.92 orn / 15.95 inches Height S625 en/1424inches Depth ss. 24 em / 7.18 inches a Power Input... DC 12V 34
\c Input AC 100 240V 50-60HZz 1.2A~0.64 AC-DC Adapter :
* Output Temperature 10 tT to35 C Humidity 10% to 80 % mon-Condensing Storage Condition Temperature = -20 to 60C Humidity 5% to 95 % nonCondensing d ae Printed in Kort 3828TUL193P {S 0009) P/NO