all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
users manual | Users Manual | 1.63 MiB | December 06 2007 | |||
1 | Block Diagram | December 06 2007 | ||||||
1 | External Photos | December 06 2007 | ||||||
1 | Internal Photos | December 06 2007 | ||||||
1 | ID Label/Location Info | December 06 2007 | ||||||
1 | Test Report | December 06 2007 | ||||||
1 | Test Report | December 06 2007 | ||||||
1 | Test Setup Photos | December 06 2007 |
1 | users manual | Users Manual | 1.63 MiB | December 06 2007 |
Test Report No.: GETEC-E3-07-045 FCC Class B Certification APPENDIX H
: USERS MANUAL EUT Type: 24 LCD Monitor FCC ID: BEJL245WHS Users Guide L245WH Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the product and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential eletrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement. Do not Open the Display. There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly. To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house. Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this display. During a lightning storm or when the display is to be left unattended for an extended period of time, unplug it from the wall outlet. A1 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently. Do not press the LCD screen with your finger for a long time as this may cause some afterimages. Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel. On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. On Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. A2 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand base or Removing the stand base 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Align the hooks on the Stand Body with the matching slots in the Stand Base. 3. Insert the hooks into slots. Hook Stand Base Slot Warning :
The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. A3 Connecting the Display 4. Attach the monitor to the Stand Base by turning the screw to the right. Screw : Turn the screw by using the screw handle. 5. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 6. Take the screw out by turning to the left to separate the monitor and Stand Base. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5~20 Swivel :350 Height Range : maximum 3.94 inch (100.0mm) 100.0mm
* Please be sure to remove the Locking pin to adjust the height. Notice You do not need to replace the Locking pin after it is removed, to adjust its height. Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Slightly wipe stained spot on the exterior only with the cleansing cloths for the product exterior if there is stain or fingerprint on surface of the exterior. Do not wipe roughly when removing stain. Please be cautious of that excessive power may cause scratch or discoloration. A5 Name and function of the Parts Rear View AC-IN DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB I O D U A T U O 2 1 9 8 7 6 1 3 5 6 7 8 9 1 2 3 4 5 AC-IN Connector : Connect the Power Cord DC-OUT Jack 2 HDMI/DVI Signal Connector COMPONENT Input Terminal 4 D-SUB Analogue Signal Connector Kensington Security Slot USB UP stream Port(1EA) USB DOWN stream Port(2EA) Audio out Jack(Headset/Earphone/connecting terminal of the Speaker)
: You can use the AUDIO-OUT Jack by connecting earphones or a headset when using the HDMI configuration..
*AUDIO-OUT is only available with the HDMI input.
(You cannot use it with D-SUB or any other component.) The Left Rear of the Monitor I O D U A T U O 2 1 UB AUDIO OUT A6 Connecting to External Devices When Connecting to your PC To adjust height of your monitor, unlock the stand lock on top of the stand. 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the 3. Connect the power cord into a proper power outlet that is easily accessible and close connection. 1 to the display. 2 I O D U A T U O 2 1 Varies according to model. DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB 2 Power Cord 1 Signal Cable Wall-outlet type NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. PC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Press button on the front switch panel to turn the power on. 5. Press the INPUT button at the front side of the monitor. MAC INPUT OK/AUTO When connecting with a HDMI/DVI signal input cable. Select HDMI : HDMI/DVI digital signal. When connecting with a D-Sub signal cable. Select RGB : D-Sub analogue signal. INPUT RGB HDMI Component A B Note How to connect to two computers. Connect the signal cables (HDMI/DVI and D-Sub) to each computer. Press the INPUT button at the front side of the monitor. Directly connect to a grounded power outlet on the wall or a power bar with a ground wire. A7 Connecting to External Devices When Watching DVD/Video/HDTV When connecting with a Component cable 1. Connect the Component cables and RCA to Stereo cables properly. Connect the terminals to the sockets of the same color. 2. Connect the power cord. Speaker AUDIO IN DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB I O D U A T U O 2 1 PBPB PB PRPR PR Monitor RCA-Stereo cable
(not included) Component Cable
(not included) DVD/VIDEO/HDTV 3. Press the INPUT button at the front side of the monitor. INPUT OK/AUTO A When connecting with a Component cable. Select Component. PBPB PB PRPR PR DVD/VIDEO/HDTV INPUT RGB HDMI Component A8 Connecting to External Devices When Watching DVD/Video/HDTV When connecting with a HDMI/DVI cable 1. Connect the HDMI/DVI cables and RCA to Stereo cables properly. I O D U A T U O 2 1 DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB HDMI/DVI cable RCA-Stereo cable
(not included) Speaker
(not included) DVD/VIDEO/HDTV 2. Press the INPUT button at the front side of the monitor. INPUT OK/AUTO A When connecting with a HDMI/DVI cable. Select HDMI. INPUT RGB HDMI Component A9 Connecting to External Devices Connecting the USB(Universal Serial Bus) Cable
"USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a single USB port; and you can hot plug (attach them while the computer is running) or unplug them while maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUS-
powered USB hub, allowing up to 2 other USB devices to be attached it. 1. Connect the upstream port of the display to the downstream port of the USB compliant 2. Connect the USB compliant peripherals to the downstream ports of the display. PC or another hub using the USB cable. (Computer must have a USB port) I O D U A T U O 2 1 MI/DVI COMPONENT Y PB PR D-SUB USB downstream Port connect the cables from USB compliant peripherals-such as keyboard, mouse, etc USB upstream Port To USB downstream port of the USB compliant PC or another hub cable 3. The monitors USB terminal supports USB 2.0 and High Speed cables. High Speed Full Speed Low Speed Data Rate 480Mbps 12Mbps 1.5Mbps Power 2.5W 2.5W 2.5W Consumption
(Max,each Port) (Max,each Port) (Max,each Port) NOTE To activate the USB hub function, the display must be connected to a USB compliant PC(OS) or another hub with the USB cable(enclosed). When connecting the USB cable, check that the shape of the connector at the cable side matches the shape at the connecting side. Even if the display is in a power saving mode, USB compliant devices will function when they are connected the USB ports(both the upstream and downstream) of the display. A10 Connecting to External Devices To arrange the cables 1. After connecting the cables neatly, arrange the cables to the Cable Holder as shown in the following figure. I O D U A T U O 2 1 AUDIO-OUT To connect HDMI, make sure that the audio cables are plugged in as show in the diagram. DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB Cable Holder
*The length of the cable which connects the monitors AUDIO-OUT and the speakers AUDIO-IN can be too long. It is used to connect the components at the appropriate distance when the AUDIO-IN terminal and the speaker are connected to the PC. Notice Be cautious to avoid the bumping the speaker against its head when removing a cable. A11 Control Panel Functions Front Panel Controls INPUT Button Select the input signal. INPUT RGB Component HDMI/DVI OK/AUTO
: 15-pin D-SUB analogue signal
: DTV SET-TOP BOX,Video,DVD
: HDMI/DVI digital signal DTV SET-TOP BOX,Video,DVD INPUT RGB HDMI Component MENU Button Controls locked Controls unlocked Use this button to enter or exit the On Screen Display. Controls locked/Controls unlocked This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU+ Button for several seconds. The message "Controls locked" should appear. You can unlock the OSD controls at any time by pushing the MENU+ Button for several seconds. The message
"Controls unlocked" should appear. A12 Control Panel Functions Use this button to select an icon or adjust the setting in the OSD screen. Button Button Use this button to directly control brightness and contrast of the PC signal (RGB, HDMI/DVI). Button Sub screen
(Picture In Picture) Button The size of the sub-screen can be changed to fit your needs Button is pressed. Main screen OK/AUTO Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the OK/AUTO button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is
- 24 inch monitor : 1920 x 1200@60Hz Auto in progress For optimal display change resolution to 1920x1200 Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. A13 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps:
Pops up the menu screen Move where you want to adjust Select a menu icon Move where you want to adjust Select a menu icon Adjust the status Save adjustment Exit from the menu screen. 1 2 3 4 5 6 Press the MENU Button, then the main menu of the OSD appears. To access a control, use the Buttons. When the icon you want becomes highlighted, press the OK/AUTO Button. Use the Buttons to adjust the item to the desired level. Accept the changes by pressing the OK/AUTO Button. Exit the OSD by pressing the MENU Button. A14 On Screen Display(OSD) Selection and Adjustment OSD (On Screen Display) menu Icon Function Description Adjusting Screen Colour. PICTURE SPECIAL SCREEN PIP/DW PIP/DW Selecting the options. Screen Adjustment. Adjusting PIP/DW Mode (Multiple Screen) Functions. NOTE OSD(On Screen Display) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation. A15 On Screen Display(OSD) Selection and Adjustment Adjusting Screen Colour EZ Video HDMI, Component input The EZ Video function automatically adjusts the screen image quality depending on the AV usage environment. Dynamic : Select this option to display with a sharp image. Standard : The most general and natural screen display status. Mild : Select this option to display with a mild image. Game : Select this option to enjoy dynamic image when playing a game. User : Select this option to use the user-defined settings. Brightness To adjust the brightness of the screen. Contrast To adjust the contrast of the screen. Color To adjust the color to desired level. Sharpness To adjust the clearness of the screen. ACC HDMI, Component input Selecting a factory setting colour set. Warm : Slightly reddish white. Normal : Slightly bluish white. Cool : Slightly purplish white. NOTE If the EZ video setting in the Picture menu is set to Dynamic, Standard, Mild or Game the subsequent menus will be automatically set. A16 On Screen Display(OSD) Selection and Adjustment Adjusting Screen Colour CSM EZ Video CSM User PC only 6500K/9300K/sRGB Selecting a factory setting colour set. 6500K: Slightly reddish white. 9300K: Slightly bluish white. sRGB : Set the screen color to fit the SRGB standard color User : Select this option to use the user-defined settings. EZ Video Brightness Contrast Red Green Blue 50 50 50 50 50 User Brightness To adjust the brightness of the screen. Contrast To adjust the contrast of the screen. Red / Green / Blue Set your own colour levels. A17 On Screen Display(OSD) Selection and Adjustment Selecting the options Input Child Lock Language Power Indicator Transparency Reset DDC-CI Input Input Child Lock Language Power Indicator Transparency Reset DDC-CI If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button. Child lock This feature can prevent unauthorized viewing. In order to lock the OSD screen adjustment, set the Child lock tab to the 'On'
position. In order to unlock it, do the following :
*Press and hold the MENU+ Button for several seconds. The message
"Controls locked" should appear. Language To choose the language in which the control names are displayed. Power Indicator Use this function to set the power indicator on the front side of the product to On or Off. Transparency To adjust the transparency of the OSD menu screen. Reset DDC-CI Use this function to reset the product to the factory default. However, language selection will not be initialized. DDC/CI(Display Data Channel Command Interface) is communication protocol for communications between PC and monitor. DDC/CI makes it possible to adjust and setup detailed functions on PC instead of the monitor OSD. Monitor can be adjusted with PC by connecting communication between PC and monitor when DDC/CI is ON, and monitor cannot be adjusted with PC because communication between PC and monitor is disconnected when DDC/CI is OFF. A18 On Screen Display(OSD) Selection and Adjustment Screen Adjustment SCREEN ARC Auto-configure Clock Phase Position HDMI ARC To select the image size of the screen.
<HDMI(Video), Component input only>
<HDMI(PC), RGB input only>
SCREEN SCREEN Full Original ARC Auto-configure Clock Phase Position HDMI Full ARC Auto-configure Clock Phase Position HDMI Auto-
Configure Clock Phase Position Full Original Full 1:1 This function is suitable for analogue signal input only. This button is for the automatic adjustment of the screen Position, Clock and Phase. This function is suitable for analogue signal input only. To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. This function is suitable for analogue signal input only. To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. SCREEN ARC Auto-configure Clock Phase Position HDMI H-Position V-Position This function is suitable for analogue signal input only. To adjust position of the screen.
/PIP button to display the sub-
Press the menu for position. Left Right Up Down Moving the screen position horizontally. Moving the screen position vertically. HDMI Video: Used when it is connected with DVD or SET-TOP BOX through HDMI. PC : Used when it is connected with PC through HDMI. NOTE When the Interlace Signal is inputted at the RGB source input level, the Auto-Configure, Clock, Phase and Position menu can't be used. A19 On Screen Display(OSD) Selection and Adjustment Adjusting PIP/DW Mode (Multiple Screen) Functions
(To adjust the sub screen) On/Off PIP Input Position Off PIP DW On/Off PIP After selecting PIP in the PIP/DW On/Off menu, the following menu items can be adjusted. DW After selecting DW in the PIP/DW On/Off menu, the following menu items can be adjusted. PIP Input To select an input signal for PIP/DW. Position To adjust the position of PIP screen. On/Off PIP Input Position Position NOTE When the Interlace signal, such as the Set-top Box, is inputted at the RGB and HDMI source input level, the following will be shown.
(1) If Interlace Signal is inputted in RGB, PIP/DW cannot be used.
(2) If Interlace Signal is inputted in HDMI, PIP/DW cannot be used.
(3) When Component is selected as the main screen for PIP/DW. If the sub-screen is an Interlace Signal inputted RGB or HDMI, the screen will be displayed but the contents will not be displayed. A20 Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the display connected?
Check and see if the power cord is connected properly to the power outlet. Is the power on and the power indicator blue or green?
Is the power indicator amber?
Do you see an "OUT OF RANGE" message on the screen?
Do you see a "CHECK SIGNAL CABLE"
message on the screen?
Adjust the brightness and the contrast. If the display is in power saving mode, move the mouse or press any key on the keyboard to activate the screen. Turn on the PC. This message appear when the signal from the PC
(video card) is out of the diplay's horizontal or vertical frequency range. See the 'Specifications'
section of this manual and configure the display again. This message appears when the signal cable between your PC and the display is not connected. Check the signal cable and try again. Do you see a "Controls locked" message on the screen?
Do you see Controls locked when you push MENU button?
You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU+
button for several seconds: the message Controls unlocked will appear. A21 Troubleshooting Display image is incorrect Display Position is incorrect. Press the OK/AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. On the screen background, vertical bars or stripes are visible. Press the OK/AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. Any horizontal noise appearing in any image or characters are not clearly portrayed. The screen color is mono or abnormal. The screen blinks. Press the OK/AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits
(true color). Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. Make sure the video card is properly inserted in the slot. Set the color setting higher than 24 bits (true color) at Control Panel - Settings. Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Make sure the power voltage is high enough, It has to be higher than AC100-240V 50/60Hz. A22 Troubleshooting Have you installed the display driver?
Have you installed the display driver?
Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lge.com. Do you see an
"Unrecognized monitor, Plug&Play (VESA DDC) monitor found"
message?
Make sure to check if the video card supports Plug&Play function. The audio function does not work. No sound?
See if the audio cable is connected properly. Adjust the volume. See if the sound is set properly. Sound is too low. Adjust the volume. A23 Specifications Display Sync Input 24 inches (61.3 cm) Flat Panel Active matrix-TFT LCD Anti-glare coating 24 inches viewable 0.270 mm pixel pitch Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Resolution Plug&Play Power Consumption
(without USB) Dimensions
&Weight Tilt/Swivel Range Power Input Environmental Conditions Analog : 30 - 83 kHz (Automatic) Digital : 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate TTL, Positive/Negative Composite TTL, Positive/Negative SOG (Sync On Green), Digital(HDCP) 15 pin D-Sub Connector HDMI/DVI connector(Digital), Component RGB Analog (0.7 Vp-p/ 75 ohm), Digital Analog : VESA 1920 x 1200 @60Hz Digital : VESA 1920 x 1200 @60Hz VESA 1920 x 1200 @60Hz Input Form Max Recommend DDC 2B 0n Mode Sleep Mode Off Mode
85 W(Typ.) 3 W 2 W With Stand Without Stand 56.00 cm / 22.05 inches 56.00 cm / 22.05 inches 44.45 cm / 17.50 inches(Min) 37.70 cm / 14.65 inches 54.45 cm / 21.44 inches(Max) 27.02 cm / 10.64 inches 8.40 cm / 3.31 inches 9.6 kg (21.1 lbs) Width Height Depth Net Tilt Swivel range 350 Height range 100 mm / 3.94 inches
-5~20 AC 100-240V~ 50/60Hz 1.2A Operating Conditions Temperature 10C to 35 C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20C to 60 C Humidity 5 % to 90 % non-Condensing A24 Specifications Stand Base Power cord USB Attached ( ), Detached ( O ) Wall-outlet type or PC-outlet type Standard USB 2.0, Self-Power Data Rate Max 480 Mbps Power Consumption Max 2.5W x 2 NOTE Information in this document is subject to change without notice. A25 Specifications Horizontal Freq. (kHz) Vertical Freq. (Hz) PC INPUT Preset Modes (Resolution) Display Modes
(Resolution) 1 2 3 4 5 6 7 8 9 10 640 x 480 640 x 480 720 x 480 720 x 400 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 768 31.47 31.47 37.50 31.47 37.88 46.88 49.72 48.36 60.02 68.68 11 12 13 14 15 16
*17 70.08 60.32 70.09 59.94 75.03 75.06 74.55 75 75 60 Display Modes
(Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1280 x 768 1280 x 1024 1280 x 1024 1600 x 1200 1600 x 1200 1680 x 1050 1920 x 1200 61.80 63.98 79.98 75.00 75.00 65.29 74.04 65.96 60.02 75.02 60 60 60.45 59.95
* Recommend Mode HDMI Video INPUT Component Video INPUT Display Modes
(Resolution) 480i 1 576i 2 480p 3 576p 4 720p 5 6 720p 7 1080i 8 1080i 9 1080p 10 1080p Indicator MODE On Mode Sleep Mode Off Mode Horizontal Freq. (kHz) Vertical Freq. (Hz) 15.75 15.62 31.50 31.25 37.50 45.00 28.12 33.75 56.25 67.50 60.00 50.00 60.00 50.00 50.00 60.00 50.00 60.00 50.00 60.00 Display Modes
(Resolution) 480i 1 576i 2 480p 3 576p 4 720p 5 6 720p 7 1080i 8 1080i Horizontal Freq. (kHz) Vertical Freq. (Hz) 15.75 15.62 31.50 31.25 37.50 45.00 28.12 33.75 60.00 50.00 60.00 50.00 50.00 60.00 50.00 60.00 LED Color Blue Amber Off A26 Specifications HDMI Type Pin Assignment No.1 No.19 No.2 No.18 Type A pin Signal Name Wire Type A pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 T. M. D. S. Data2+
T. M. D. S. Data2 Shield T. M. D. S. Data2-
T. M. D. S. Data1+
T. M. D. S. Data1 Shield T. M. D. S. Data1-
T. M. D. S. Data0+
T. M. D. S. Data0 Shield T. M. D. S. Data0-
T. M. D. S. Clock+
T. M. D. S. Clock Shield T. M. D. S. Clock-
CEC Reserved(In cable but N.C. on device) SCL SDA DDC/CEC Ground
+5V Power Hot Plug Detect A B A A B A A B A A B A C C C C D 5V C T. M. D. S. (Transition Minimized Differential Signaling) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 USB Connector Pin Assignment UP stream Down stream 2 1 3 4 1 2 3 4
#1:VCC #2 : Data -
#3:Data + #4 : GND Series B connector Series A connector Female Connector View A27 How to Install the VESA Standard wall mounting This monitor meets VESA-compliant mounting interface pad specifications. 1. After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage. I O D U A T U O 2 1 DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB I O D U A T U O 2 1 DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB I O D U A T U O 2 1 DC-OUT HDMI/DVI COMPONENT Y PB PR D-SUB 2. Separate the head and the stand with the use of a screwdriver. 3. Set up the VESA standard Stand Base. VESA wall mounting Connected to another object (stand type and wall-mounted type. This monitor accepts a VESA-compliant mounting interface pad.-
This has to be purchased separately if required.) For further information, refer to the VESA Wall Mounting Instruction Guide. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores. A28 Digitally yours Regulatory information Regulatory information Regulatory Information cont. FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) Products with the CE Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :
EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 60950
; Radio Frequency Interference
; Electromagnetic Immunity
; Power Line Harmonics
; Voltage Fluctuations
; Product Safety NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO95 (TCO95 applied model only) Congratulations!
You have just purchased a TCO95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. 01 Regulatory Information cont. Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem as far as computers and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic- and climatic-
influencing emissions, radioactive waste, etc.), it is vital to conserve energy. Electronic equipment in offices consumes as enormous amount of energy, since it is often routinely left running continuously. What does the environmenal labelling involve?
This product meets the requirements for the TCO95 scheme, which provides for international environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturckyddsfreningen (The Swedish Society for Nature Conservation), and NUTEK (The National Board for Industrial and Technical Development in Sweden), and SEMKO AB (an international certification agency). The requirements cover a wide range of issues:
environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern, among other things, restriction on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs
(freons), and chlorinated solvents. The product must be prepared for recycling, and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the 02 computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability. The following is a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:
TCO Development Unit Linnegatan 14, S-11494 Stockholm, Sweden FAX +46-8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO95 approved and labelled products may also be obtained on the Internet using the address: http://www.tco-info.com/
TCO95 is a co-operative project between:
NUTEK SEMKO Nrings- och teknikutvecklingsverket Naturskydds freningen Environmental requirements Brominated flame retardants are present in printed circuit boards, cabling, casings, and housings, and are added to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame-retardant substances. These are related to another group of environmental toxins, PCBs, and are suspected of giving rise to similar harm, including reproductive damage in fish-
eating birds and mammals. Flame retardants have been found in human blood, and researchers fear that they can disturb fetus development. Bio-accumulative1 TCO95 demands require that plastic components weighing more than 25 grams must not contain flame retardants with organically bound chlorine or bromine. Lead can be found in picture tubes, display screens, solder, and capacitors. Lead damages the nervous system and in higher doses causes lead poisoning. The Regulatory Information cont. relevant bio-accumulative TCO95 requirement permits the inclusion of lead, as no replacement has yet been developed. Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium. The color-
generating layers of display screens must not contain any cadmium. Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO95 requirement states that batteries may not contain more than 25 ppm of mercury and that no mercury is present in any of the electrical or electronic components concerned with the display unit. CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacture of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the atmosphere, causing increased reception on Earth of ultra-violet light with consequent increased risks of skin cancer (malignant melanoma). The relevant TCO95 requirement: Neither CFCs nor HCFCs may be used during the manufacture of the product or its packaging. 1 Bio-accumulative means that the substance accumulates within living organisms. Shipping Package The packaging material can be recycled, or you can save it to return the monitor to a service center for repair or disposal. CFC Compounds in Distribution Packaging Cushioning material used for shipping finished monitors are not manufactured with nor do they contain any CFC compounds. Design for Disassembly/Recycling These monitors have been designed for easy end-of-life disassembly and recycling. Fasteners are generally of the same type for efficient disassembly. Components made of different materials can be easily separated and plastics have been identified using intermational symbols to aid in recycling. Monitor Disposal WARNING If you need to dispose of a monitor, ask a qualified service representative for the proper procedure. Improper disposal could result in personal injury from implosion. TCO'99 (TCO'99 applied model only) Congratulations!
You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. What does labelling involve?
The product meets the requirements for the TCO99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). 03 TCO99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Mercury**
Mercury is sometimes found in batteries, relays and switches. TCO99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. TCO99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________
* Bio-accumulative is defined as substances which accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. Regulatory Information cont. Approval requirements cover a wide range of issues:
ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Developments website http://www.tcodevelopment.com or may be ordered from:
TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30%
by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes when not disposed of in accordance with strict standards for disposal. 04 Regulatory Information cont. TCO03 (TCO03 applied model only) with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www.tcodevelopment.com English Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our green policies. http://www.lge.com/experience/social_commitment/enviro ment.jsp Congratulations!
The display you have just purchased carries the TCO03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO03 Display requirements:
Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started 05 Regulatory Information cont. Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkndete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklrung fr eine sauberere Umwelt). Seitdem dient dieses Ideal als fhrendes Prinzip des Unternehmens. Diese Erklrung war die Basis fr die Durchfhrung von umweltfreundlichen Aktivitten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die berlegungen mit einbezogen wurden. Wir frdern Aktivitten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schdlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Informationen zum Thema Recycling Dieser Monitor enthlt Teile, die umweltschdlich sein knnen. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er auer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rcknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schdliche Substanzen und Schwermetalle werden durch umweltvertrgliche Verfahren behandelt. Falls Sie mehr ber unser Recyclingprogramm erfahren mchten, wenden Sie sich bitte an Ihren lokalen LG-
Hndler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einflieen lassen. Zustzliche Informationen ber unsere grne Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/experience/social_commitment/enviro ment.jsp Franais Information sur la protection de lenvironnement LGE. a publi sa 'Dclaration en faveur dun 06 environnement plus propre' en 1994 et celle-ci est reste, depuis lors, un principe directeur de notre entreprise. Cette dclaration a servi de base notre rflexion et nous a permis de prendre en compte la fois les aspects conomiques et sociaux de nos activits, tout en respectant lenvironnement. Nous encourageons les activits en faveur de la prservation de lenvironnement et cest dans cet esprit que nous dveloppons nos produits : nous rduisons au minimum les matires dangereuses qui entrent dans leur composition et lon ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui prsentent un risque pour lenvironnement. Il est donc important que celui-ci soit recycl aprs usage. LGE. traite les moniteurs en fin de cycle conformment une mthode de recyclage respectueuse de lenvironnement. Nous reprenons nos produits et les recyclons dans plusieurs sites rpartis dans le monde entier. De nombreux composants sont rutiliss et recycls, et les matires dangereuses, ainsi que les mtaux lourds, sont traits selon un procd cologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un lun de nos reprsentants. Nous voulons agir pour un monde plus propre et croyons au rle de notre entreprise dans lamlioration de lenvironnement. Pour plus de renseignements sur notre politique verte, rendez visite notre site :
http://www.lge.com/experience/social_commitment/enviro ment.jsp Italiano Informazioni per la tutela dellambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente pi pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attivit a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali. Regulatory Information cont. Noi della LG, promuoviamo attivit a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dellambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non presente il cadmio. Informazioni per il riciclaggio Il monitor pu presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dellambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo pi pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica verde. http://www.lge.com/experience/social_commitment/enviro ment.jsp Espanl Informacin para la conservacin medioambiental LGE. present la 'Declaracin para un entorno ms limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaracin es la base que nos ha permitido llevar a cabo tareas que respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, econmicos y medioambientales. Promocionamos actividades orientadas a la conservacin del medio ambiente y desarrollamos nuestros productos especficamente para que se ajusten a la filosofa que protege el entorno. Reducimos al mximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. Informacin para el reciclaje Este monitor puede contener piezas que entraen riesgos medioambientales. Es importante reciclar este monitor despus de su utilizacin. LGE. trata todos los monitores usados siguiendo un mtodo de reciclaje que no daa al entorno. Contamos con diversos sistemas de recuperacin y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dainas y los metales pesados se tratan siguiendo un mtodo que no perjudique al medio ambiente. Si desea obtener ms informacin acerca del programa de reciclaje, pngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Basamos nuestra visin y nuestras polticas en un mundo ms limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolucin como empresa. Visite nuestra pgina Web para obtener ms informacin sobre nuestras polticas ecolgicas. http://www.lge.com/experience/social_commitment/enviro ment.jsp Portugus Informaes relacionadas preservao ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declarao da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde ento como um princpio administrativo de orientao. A Declarao a base que nos tem permitido realizar atividades favorveis ao ambiente com considerao atenta aos aspectos econmicos, ambientais e sociais. Promovemos atividades de preservao ambiental e desenvolvemos nossos produtos para englobar especificamente o conceito de favorvel ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, no h cdmio em nossos monitores. 07 Regulatory Information cont. Informaes relacionadas reciclagem Este monitor pode conter peas que podem representar riscos ao ambiente. importante que ele seja reciclado aps o uso. A LGE. cuida de todos os monitores descartados atravs de um mtodo de reciclagem agradvel ao ambiente. H vrios sistemas de devoluo e reciclagem atualmente em operao no mundo. Muitas peas sero reutilizadas e recicladas e as substncias nocivas e os metais pesados passaro por tratamento atravs de um mtodo favorvel ao ambiente. Para obter mais informaes sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa viso e nossas polticas relacionadas a um mundo mais limpo selecionando a questo do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informaes sobre nossas polticas de meio ambiente. http://www.lge.com/experience/social_commitment/enviro ment.jsp Nederlands Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze 08 monitor aan het einde van zijn levensduur wordt gerecycled. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LG-
vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/experience/social_commitment/enviro ment.jsp Russian 1994 LGE
' LG ',
. LG LG . LG
. http://www.lge.co.kr/about/digitallg/environment/environment.jsp EPA (U.S.A only) (EPA applied model only) ENERGYSATR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) Regulatory Information cont. K LGE
. LG.
http://www.lge.com/experience/social_commitment/enviro ment.jsp LG 1994 'LG '
. LG
. LG
. 09
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-06-12 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-06-12
|
||||
1 | Applicant's complete, legal business name |
LG Electronics USA
|
||||
1 | FCC Registration Number (FRN) |
0023476120
|
||||
1 | Physical Address |
1000 Sylvan Avenue
|
||||
1 |
Englewood Cliffs, New Jersey 07632
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
BEJ
|
||||
1 | Equipment Product Code |
L245WHS
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
K****** H****
|
||||
1 | Title |
Director, Standards & Compliance
|
||||
1 | Telephone Number |
201-4********
|
||||
1 | Fax Number |
201-8********
|
||||
1 |
k******@lge.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 24" LCD Monitor | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
GUMI UNIVERSITY EMC CENTER
|
||||
1 | Name |
T****** P******
|
||||
1 | Telephone Number |
82-54********
|
||||
1 | Fax Number |
82-54********
|
||||
1 |
t******@gumi.ac.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC