Bluetooth Module : MB8811C1
[top] [bottom]
This MB8811C1 Module is compatible with Bluetooth specification version 4.0. MB8811C1 is a fully integrated RF, baseband controller etc. SPECIFICATION Main Chips Standards Frequency Band Tx Power CSR8811 Bluetooth 4.0+BLE 2402 ~ 2480 MHz 7mW Rx Sensitivity
< -70dBm (BER 0.1%) Distance
< 10m (open space) Power Voltage 3.3V Dimension 18.631.2 3.4 mm Operation temperature : -10 ~ +70 GFSK, 8DPSK, FHSS k/4 DQPSK Environmental Range Modulation mode Communication method Pin define(TOP PIN MAP) No Pin Name I/O Description 1 2 3 4 5 6,7,8,12 9 10 11 CTS VDD TXD RTS RXD GND SDA SCL RESET I I O O I
Bluetooth UART Clear to Send.Active-low clear. Positive Input for the internal regulator (3.0 ~ 3.6V) Bluetooth UART Serial Output. Bluetooth UART Request to Send. Active-low request. Bluetooth UART Serial Input. Ground. I/O I2C interface DATA O I I2C interface Clock Reset if low. Input debounced so must be low for >5ms to cause a reset 1. VDD2.RESET3.RTS4.CTS5.TXD6.GND7.RXD8.GND9. SCL10. SDA Pin define(BOTTOM PIN MAP) No Pin Name I/O Description 1 2 3 4 5 6,7,8,12 9 10 11 CTS VDD TXD RTS RXD GND SDA SCL RESET Bluetooth UART Clear to Send.Active-low clear. Positive Input for the internal regulator (3.0 ~ 3.6V) I I O Bluetooth UART Serial Output. O Bluetooth UART Request to Send. Active-low request. Bluetooth UART Serial Input. I
- Ground. I/O O I I2C interface DATA I2C interface Clock Reset if low. Input debounced so must be low for >5ms to cause a reset 2. VDD11.RESET4. RTS1. CTS3. TXD5. RXD6. GND10. SCL9. SDA8. GND7. GND12. GND Dimension Mark Dimension Mark Dimension Mark Dimension Mark Dimension Mark Dimension A B C 18.600.3 31.200.3 9.700.3 D E F 3.900.2 8.400.2 2.00.3 G H I 2.00.2 1.90.2 0.80.1 J K L 6.40.2 4.90.2 2.60.2 M N O 3.40.2 5.00.2 5.10.2
(Unit : mm) Electrical Characteristics Conditions : VDD = 3.3V, Ta = 25 , unless otherwise noted. Absolute Maximum Ratings Parameter Power Supply Voltage : VDD Storage Temperature Recommended Operating Conditions Min
-0.4V
-40 Max 3.6V 85 Unit DCV Parameter Power Supply Voltage Operation Temperature Current consumption Min 3.0V
-10 Max 3.6V 70 Unit DCV Parameter Connection Type Avg Peak Unit Page scan, Time interval = 1.28s Inquiry and Page scan, Time interval = 1.28s ACL No data transfer ACL data transfer Input/Output Characteristics Parameter VIL Input Voltage Low VIH Input Voltage High VOL Output Voltage Low VOH Output Voltage High
Master Master 2 2 10 32 3 mA mA mA mA Min
-0.4 Max 0.8 0.7*VDD VDD+0.4
VDD-0.2 0.2
Unit V V V V General Performance Parameter Condition Min Typ Max Unit Frequency Range Normal 2402
2480 MHz Transmitter Performance Parameter Condition Min Typ Max Unit Transmit Power Power density 20dB bandwidth Adjacent channel power
(F0 = 2441MHz) Out-band Spurious Emission Modulation Characteristic Initial Carrier Frequency Tolerance Carrier Frequency Drift Receiver Performance Normal Normal Normal F=F0 2MHz F=F0 3MHz F=F0 4MHz 30MHz ~ 1GHz 1GHz ~ 12.75GHz 1.8GHz ~ 1.9GHz 5.1GHz ~ 5.3GHz F1avg F2max F2avg / F1avg DH1 packet DH5 packet
-6 0
140 115 80
-75
-25
8 20 dBm dBm 1000 KHz
-20
-40
-40
-36
-30
-47
-47 175
75 25 dBm dBm dBm dBm dBm dBm dBm KHz KHz
KHz KHz Parameter Condition Min Type Max Unit Sensitivity at 0.1% BER Single slot (DH1 packet) Sensitivity at 0.1% BER Multi slot (DH5 packet) Maximum received signal at 0.1% BER Maximum level of intermodulation interferers f1-f2 = 5 MHz, Pwanted= -64 dBm
-70
-70
-20
-39
dBm dBm dBm dBm MB8811C1 Test Manual 1) RF Test Utility 2) First time, CSR Bluesuite program must be installed. you can use BTCli.exe and enter DUT(Device Under Test) mode. So RF equipment can inquiry and test. (reference document.)
* reference document : MB8811C1_JIG_Bluetest3 setting manual.pdf 3) RF Test method RF Test tool is BlueTest.exe at CSR bluesuite program. You can see detail explanation from reference document.
* reference document : BlueTest Instruction Manual.pdf Conformity Assessment Display Company name: MCSLogic Model : MCS Bluetooth Smart Device Module (MB8811C1) Manufacture Year : 2014. Manufacturer / Manufacture Country : MCSLogic / Korea Operation of the radio equipment may cause propagation interference, and so the life-saving services could not be STATEMENT and Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. French:
Cet appareil radio est conforme au CNR-210 dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 19-1, Cheongho-ri Jinwi-myeon, Pyeongtaek-si,Gyeonggi-do, 451-713, Korea NCC NCC:XXXXXXXXXXX This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. 19-1, Cheongho-ri Jinwi-myeon, Pyeongtaek-si,Gyeonggi-do, 451-713, Korea End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: BEJ9QK-DMMB8811C1, contains IC: 2703H-DMMB8811C1. The grantee's FCC ID can be used only when all FCC/ IC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. CE Hereby declares that this WiFi module is in compliance with the essential requirements and other relevant provisions of R&TTE Directive 1999/5/EC. The standards for complying are as following:
ETSI EN 301 489-1 V1.9.2: 2011-09 ETSI EN 301 489-17 V2.2.1: 2012-09 ETSI EN 300 328 V1.8.1:2012-06 EN 62311: 2008 EN 60950-1: 2006 +A11:2009+A1:2010+A12:2011+A2:2013 This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device is intended for home and office use in all EU countries