User Manual PRODUCT NAME : Bluetooth Class1 ROM Module MODEL NAME : WB1BH5
(00)-0073 REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 Table of Contents User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
1 / 11 No. Description 1 1 2 3 4 5 5 6 7 8 9 Features Features Block Diagram Certification condition Storage Conditions O Operating Conditions Interface Specification Pin Description Outline Drawing Packing Information ti C diti Page 2 2 2 3 5 5 5 6 8 9 10 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 1. Features User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
2 / 11 WB1BH5 is the small size and low power module for Bluetooth 4.0. WB1BH5 is based on TI CC2564B. Bluetooth 4.0 / Class I Size : 34mm x 19mm x 3.1 mm Internal PCB Printed Antenna UART with maximum rate of 4 Mbps interface Digital PCM-I2S codec interface Supports drivers for Windows 7, Vista, XP, 2000 and Linux Application : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Block Diagram 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
3 / 11 3. Certification condition FCC approval The satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID : BEJ9QK-DMWB1BH5 p This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators and following statements shall be included to host user manual 1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) This module may not be co-located with any other transmitters or antennas. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC authorizations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. i i f l i Thi t ll ti id ti This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful i t interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver. C
- Connect the equipment into an outlet on a circuit different from it diff t f di di d t t t t f t th i that to which the receiver is connected. t i tl t i
- Consult the dealer or an experienced radio/ TV technician for help. CE approval Hereby, LG declares that this device is compliance with the essential requirements and other relevant 1999/5/EC provisions of directive 1999/5/EC. f di ti i i 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
4 / 11 IC approval t ti t t itif d'
il d i The host device must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 2703H-DMWB1BH5 ffi h L di Le dispositif d'accueil doivent tre tiquets pour afficher le numro de certification d'Industrie Canada du module. Contient module metteur IC : 2703H-DMWB1BH5 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. d'I d t i C d d tifi d ti l Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opration est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interfrences, et (2) cet appareil doit accepter toute interfrence, y compris les interfrences quipeuvent causer un mauvais fonctionnement de l'appareil. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. y p pp Cet appareil est conforme aux limites d'exposition aux rayonnements d'Industrie Canada pour un environnement non contrl. Cet appareil doit tre install et utilis distance minimum de 20cm entre l'lment rayonnant de cet appareil et l'utilisateur. REMARQUE : LE FABRICANT N'EST PAS RESPONSABLE DES INTERFRENCES RADIOLECTRIQUES CAUSES PAR DES MODIFICATIONS NON AUTORISES APPORTES CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDE L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL p 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
5 / 11 4. Storage Conditions Parameter Storage Temperature Storage Temperature Storage Humidity (@ 40) Min
-10 10
-
Max
+80 80 90 Unit
%
Caution : The specifications above the Table define levels at which permanent damage to the device can occur Function operation is not guaranteed under these conditions to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40 and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. 5. Operating Conditions Parameter Min Typ Ambient Temperature Operating Humidity (40) 0
-
-
-
Supply Voltage 3.15 3.3 Max
+70 85 3.45 Unit
%
Vdc 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
6 / 11 6. Interface Specification 1) UART Figure 11-1 shows the UART timing diagram. Table 11-1 lists the UART timing characteristics Figure 11 2 shows the UART data frame Table 11 2 describes characteristics. Figure 11-2 shows the UART data frame. Table 11-2 describes the symbols used in Table 11-2.
[ Figure 11-1. UART Timing ]
[ Table 11-1. UART Timing Characteristics]
[ Figure 11-2. Data Frame]
[ Table 11-2. Data Frame Key ]
2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
7 / 11 2) PCM Figure 11-3 shows the interface timing for the PCM. Table 11-3 and Table 11-4 Lists the associated master and slave parameters Lists the associated master and slave parameters.
[ Figure 11-3. PCM Interface Timing ]
[ Table 11-3. PCM Master ]
[ Table 11-4. PCM Slave ]
2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 7. Pin Description User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
8 / 11
< TOP View > < Bottom View >
1 2 2 1 Note. 1) Recommend a Module install sequence for prevent USB device failure
- Supply 3.3V power l (UART TX RX)
- Connect to data signal (UART TX, RX) C i t t d t 2) Connector: 12Pin SMD Connector A 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 8. Outline Drawing User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
9 / 11 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
10 / 11 9. Packing Information 2014 LGIT. All rights reserved. REG. DATE : 2014.10.29 REV. DATE : 2014.10.29 User Manual MODEL: WB1BH5 REV.NO : 1.0 PAGE :
11 / 11 2014 LGIT. All rights reserved.